2006 MERCEDES-BENZ C350 4MATIC remote control

273 Controls in detail
Useful features
Stolen Vehicle Recovery services
In the event your vehicle was stolen:
Report the incident to the police.
The police will issue a numbered
incident report.

Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is
located, the Response Center will
contact the local law enforcement and
you. The vehicle’s location will only be
provided to law enforcement.
Garage door opener*
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
Interior rear view mirror with integrated re-
mote control1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
ton
iWhen the anti-theft alarm or the
tow-away alarm stays on for more than
30 seconds, a call is initiated automat-
ically to the Response Center. See
anti-theft alarm system* (
page 93)
and tow-away alarm* (
page 95).

274 Controls in detailUseful features
Programming or reprogramming the
integrated remote control
Step 1:
Switch on the ignition (
page 33).Step 2:

If you have previously programmed an
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
- signaling the door to stop and reverse -
does not meet current U.S. federal safety
standards.
When programming a garage door opener
park the vehicle outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide, and
inhaling it can cause unconsciousness and
possible death.

275 Controls in detail
Useful features
Step 3:
Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in (5
to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping the indicator
lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
The indicator lamp1 will flash, first
slowly and then rapidly.Step 5:

After the indicator lamp1 changes
from a slow to a rapidly flashing light,
release the hand-held remote control
button and the signal transmitter but-
ton.Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.
If the indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
iThe indicator lamp1 flashes immedi-
ately the first time the signal transmit-
ter button is programmed. If this button
has already been programmed, the in-
dicator lamp will only start flashing af-
ter 20 seconds.
iIf the indicator lamp1 flashes rapidly
for about 2 seconds and then turns to a
constant light, continue with
programming steps 8 through 12 as
your garage door opener may be
equipped with the “rolling code”
feature.


277 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner. If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:

Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.
iSome garage door openers (or other
rolling code equipped devices) may re-
quire you to press, hold for 2 seconds
and release the same signal transmit-
ter button a third time to complete the
training process.


278 Controls in detailUseful features
Proceed with programming step 5 and
step 6 to complete. Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Switch on the ignition (
page 33).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the signal transmitter button, pro-
ceed with programming starting with
step 3.Operation of integrated remote control

Switch on the ignition (
page 33).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
iUpon completion of programming the
integrated remote control, make sure
you retain the hand-held remote con-
trol that came with the garage door
opener, gate operator or other device.
You may need it for use in other vehi-
cles, for future programming of an
integrated remote control, or simply for
continued use as a hand-held remote
control to operate the respective
device in other situations.


279 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on the ignition (
page 33).

Simultaneously press and hold down
the outer signal transmitter buttons2
and 4, for approximately 20 seconds,
until the indicator lamp1 flashes rap-
idly. Do not hold for longer than
30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:


Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.


Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.


While performing step 3, hold the
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes
of all three channels.
iCertain types of garage door openers
are incompatible with the integrated
remote control. If you should experi-
ence further difficulties with program-
ming the integrated remote control,
contact an authorized Mercedes-Benz
Center, or call Mercedes-Benz
Customer Assistance Center (in the
USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.

458 IndexControl system submenus 132, 134
Convenience 153
Instrument cluster 143
Lighting 149
Time/Date 145
Vehicle 152
Controller Area Network see CAN system
Coolant 301, 444
Anticorrosion/antifreeze
quantity 445
Capacities 440, 441
Checking coolant level 295, 301
Messages in display 371–373
Temperature 293
Temperature gauge 25, 128
Corner-illuminating front fog lamps* 123
Replacing bulbs 398
Cruise control 247, 450
Message in display 374
Cup holder 259, 260
Cleaning 346
Curb weight 331
Customer Assistance Center see CACD
Date display, setting 147, 148
Daytime running lamp mode 120
Setting 149
Deep water see Standing water
Defogging windshield
Automatic climate control*
(Canada only) 192
Climate control 181
Defrosting, Front
Automatic climate control*
(Canada only) 191
Climate control 181
Defrosting, Rear 175
Delayed shut-off
Exterior lamps 151
Interior lighting 152
Department of Transportation see DOT
Difficulties
While driving 56
With starting 50
Digital clock see clock
Digital speedometer 135Dimensions, vehicle 438
Direction of rotation (tires) 307
Displays
Digital speedometer 135
Maintenance service indicator 338
Messages in display 374
Multifunction display 130
Outside temperature 135
Symbol messages 369
Text messages 360
Vehicle status messages
memory 139, 358
Distance to empty (range),
Trip computer 156
Door control panel 30
Doors
Entry lamps 126
Locking/unlocking, SmartKey 98
Message in display 374
Opening from inside/outside 100,
102
Remote door unlock (Tele Aid*) 272
Unlocking, Mechanical key 389

459 Index
DOT 331
Downhill driving
Cruise control 248
Drinking and driving 283
Driving
Abroad 290
Hydroplaning 287
In winter 289
Instructions 45, 283
Problems 56
Safety systems 87
Systems 247
Through standing water 290
Driving safety systems
4MATIC 92
ABS 87
BAS 88
ESP
®
89E
Easy-entry/exit feature* 42, 153
Electrical fuses see Fuses
Electrical outlet 263
Electrical system, Technical data 437
Electronic Stability Program see ESP
®
Emergency calls
911 calls 237
Tele Aid* calls 267, 268, 271
Emergency operation
(Limp Home Mode) 169
Emergency operations
Fuel filler flap 391
Gear selector lever, Unlocking 392
Locking/unlocking the vehicle 389
Power tilt/sliding sunroof*,
Manual operation 393
Remote door unlock 272
Trunk lid, Releasing from inside 105
Trunk lid, Unlocking 390
Emergency Tensioning Device see ETDEmergency, in case of
Battery, Jump starting 415
First aid kit 350, 383
Flat tire, Changing 406
Fuses 421
Hazard warning flasher 124
Instrument cluster,
Indicator lamps 350–355
Roadside Assistance 12, 268
Towing the vehicle 417
Emission control 292
Information label 428
System warranties 10
Engine
Belt layout 429
Block heater (Canada only) 337
Brake-in recommendations 282
Cleaning 343
Compartment 297
Malfunction indicator lamp 25, 352
Maximum engine speed 430