2006 MERCEDES-BENZ C280 change time

218 Controls in detailAudio systemTips on handling CDs

Handle CDs carefully to prevent
interference during playback.


Avoid scratches, fingerprints and dust
on the CDs.


Do not write on CDs or apply any labels
or other material to them.


Clean CDs from time to time with a
commercially available cleaning cloth.
Never wipe the CD in a circular motion;
instead, wipe it in a straight line start-
ing in the center and moving outward.
Do not use solvents, anti-static sprays,
etc. for cleaning.


Replace the CD in its case after use.


Protect CDs from heat and direct
sunlight.MP3
The CD changer* can play audio CDs as
well as CDs with MP3 files.
Information on MP3 data carriersCompatible MP3 data carriers
The CD changer can read the following
data carriers in MP3 mode:


CD-DA


CD-R


CD-RW
Compatible file systems and compres-
sion methods
Use Romeo or Joliet. Depending on file for-
mat used, up to 128 characters are possi-
ble.
The following compression methods are
compatible:


MP3


WMA


WAV
iCD media, CD burning software and
CD writers are available in great vari-
ety. Due to this variety, it cannot be
guaranteed that the CD changer will be
able to play every user-written CD.
The burning process can lead to data
errors and aging of the medium may re-
sult in data loss. Therefore, the
CD changer may be restricted in its
ability to play MP3 data carriers; it may
play them with reduced sound quality,
or it m ay not b e a bl e to pl ay them a t al l.
Problems may be encountered during
playback of user-written CDs with a
storage capacity of more than 700 MB.
These CDs do not meet valid standards
as of this printing.

221 Controls in detail
Audio system
1CD
2CD changer
3CD tray
4CD magazine
Remove magazine4 and pull
CD tray3 fully out.

Place CD1 in recess of tray, label side
up.

Push tray into magazine in direction of
arrow.

Push magazine into CD changer*2 in
direction of arrow and close sliding
door.
Playing CDs
Single CD player in the audio unit

Pressi button.CD 0
will appear in the upper left-hand
corner of the display.
The CD will resume playback at the point
where it was switched off.CD changer*

Press Q button.CD and the selected magazine slot
number appear in the upper left-hand
corner of the display.
If you have not removed a CD since the last
time the CD audio source was activated,
the last CD listened to will begin to play at
the point where it was switched off.
After the last track on a CD has finished,
the next CD is automatically played.
iCDs which have been inserted
improperly or are unreadable will not
be played.

224 Controls in detailAudio systemRepeat
The track being played is repeated until the
repeat function is switched off.

Switching on repeat
Press
RPT
soft key.
RPT appears in the display.


Switching off repeat
Press
RPT
soft key again.Pause function
The CD changer mode is interrupted by an
incoming call on the telephone*
(
page 229).


Switching on pause function
Press U button.
The CD changer mode is
interrupted and
PAUSE
appears in
the display.


Switching off pause function
Press U button.
The CD changer mode is active
again.Track and time display

Press
T soft key.
The number of the track being played
and the elapsed playing time appear in
the display.

Press
T soft key again.
The total number of tracks and the total
playing time of the CD appear in the
display.

Press
T soft key.
The standard CD playback menu
appears in the display.
iWhen you start the RPT function, the
RDM function is automatically
switched off.

247 Controls in detail
Driving systems
Driving systems
The driving system of your vehicle is
described on the following pages:

Cruise control, with which the vehicle
can maintain a preset speed.
For information on the BAS, ABS, and ESP
®
driving systems, see “Driving safety sys-
tems” (
page 87).
Cruise control
Cruise control automatically maintains the
speed you set for your vehicle.
Use of cruise control is recommended for
driving at a constant speed for extended
periods of time. You can set or resume
cruise control at any speed over 20 mph
(30 km/h).
The cruise control function is operated by
means of the cruise control lever.
The cruise control lever is the uppermost
lever on the left-hand side of the steering
column (
page 22).
Warning!
G
Cruise control is a convenience system de-
signed to assist the driver during vehicle op-
eration. The driver is and must remain at all
times responsible for the vehicle speed and
for safe brake operation.
Only use cruise control if the road, traffic
and weather conditions make it advisable to
travel at a steady speed.

The use of cruise control can be danger-
ous on winding roads or in heavy traffic
because conditions do not allow safe
driving at a steady speed.


The use of cruise control can be danger-
ous on slippery roads. Rapid changes in
tire traction can result in wheel spin and
loss of control.


Deactivate cruise control when driving
in fog.
The “Resume” function should only be oper-
ated if the driver is fully aware of the previ-
ously set speed and wishes to resume this
particular preset speed.

275 Controls in detail
Useful features
Step 3:
Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in (5
to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping the indicator
lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
The indicator lamp1 will flash, first
slowly and then rapidly.Step 5:

After the indicator lamp1 changes
from a slow to a rapidly flashing light,
release the hand-held remote control
button and the signal transmitter but-
ton.Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.
If the indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
iThe indicator lamp1 flashes immedi-
ately the first time the signal transmit-
ter button is programmed. If this button
has already been programmed, the in-
dicator lamp will only start flashing af-
ter 20 seconds.
iIf the indicator lamp1 flashes rapidly
for about 2 seconds and then turns to a
constant light, continue with
programming steps 8 through 12 as
your garage door opener may be
equipped with the “rolling code”
feature.


450 Technical termsControl system
The control system is used to call up
vehicle information and to change
component settings. Information and
messages appear in the multifunction
display. The driver uses the buttons on
the multifunction steering wheel to
navigate through the system and to
adjust settings.
Cruise control
Driving convenience system that
automatically maintains the vehicle
speed set by the driver.
Curb weight
(
page 331)
DOT
(Department o
f Transportation)
(
page 331)Engine number
The number set by the manufacturer
and placed on the cylinder block to
uniquely identify each engine
produced.
Engine oil viscosity
Measurement for the inner friction
(viscosity) of the oil at different temper-
atures. The higher the temperature an
oil can tolerate without becoming thin,
or the lower the temperature it can
tolerate without becoming viscous, the
better the viscosity.
ESP
®(Electronic S
tability P
rogram)
Improves vehicle handling and
directional stability.
ETD
(E
mergency T
ensioning D
evice)
Device which deploys in certain frontal
and rear collisions exceeding the
system’s threshold to tighten the
seat belts.
->SRSFSS (Canada vehicles)
(F
lexible S
ervice S
ystem)
Maintenance service indicator in the
multifunction display that informs the
driver when the next vehicle mainte-
nance service is due. FSS evaluates
engine temperature, oil level, vehicle
speed, engine speed, distance driven
and the time elapsed since your last
maintenance service, and calls for the
next maintenance service accordingly.
GAWR
(G
ross A
xle W
eight R
ating)
(
page 331)
Gear range
Number of gears which are available to
the automatic transmission for shifting.
The automatic gear shifting process
can be adapted to specific operating
conditions using the gear selector
lever.

456 Index
Operating and display elements 200
Operating audio system 202
Operating safety 199
Radio operation 207
Telephone* operation 225
Auto-dimming mirror* 171
Automatic central locking
Activating/deactivating
(Control system) 152
Automatic climate control*
(Canada only) 186
Control panel 187
Defrosting, front 191
Rear window defroster 175
Automatic headlamp mode 119
Automatic locking when driving 107
Automatic shift program
Program mode selector switch
(Automatic transmission*) 167
Automatic time change (Standard time,
Daylight Saving time) 147Automatic transmission* 162
Accelerator position 165
Automatic shift program 167
Emergency operation
(Limp Home Mode) 169
Fluid level (ATF) 300
Gear ranges 166
Gear selector lever 162
Gear shifting malfunctions 169
Kickdown 165
Manual shifting 168
One-touch gearshifting 168
Program mode selector switch 167
Starting engine 49
B
Backrest
Driver’s multicontour seat*
(Canada only) 113
Rear seat, folding 254
Seat, manual 36
Seat, power* 38Backup lamps
Messages in display 377
Replacing bulbs 399
Bar 331
BAS 88, 449
Batteries, SmartKey
Changing 396
Checking battery condition 101
Battery, Vehicle 302, 412
Charging 414
Disconnecting and connecting 413
Jump starting 415
Removing and installing 413
Bead 331
Bi-Xenon* headlamps see headlamps
Block heater (Canada only) 337
Bolts, Spare wheel 388
Brake Assist System see BAS
Brake fluid 442
Checking 295
Message in display 370

457 Index
Brake lamps
Cleaning lenses 344
Messages in display 377
Replacing bulbs 403
Brake pads
Message in display 370
Brakes 284
Warning lamp 25, 351
Break-in period 282
Bulbs, replacing see Replacing bulbs
C
CAC 449
California retail buyers and lessees,
important notice 11
CAN system 449
Cargo area see Trunk
Cargo tie-down rings* 256
Carpets, cleaning 347
Catalytic converter 291
CD changer* 216
CD player* 137, 216
Centigrade see Temperature display
mode 142Central locking
Automatic 107, 152
From inside 107
Locking/unlocking from inside 107
Switch 107
Certification label 428
Charcoal filter
Automatic climate control*
(Canada only) 194
Children in the vehicle 74
Air bags 64
Blocking rear door window
operation 85
Indicator lamp, front passenger
air bag 80, 356
Infant and child restraint systems 74
LATCH-type child seat anchors 83
Occupant Classification System
(OCS) 77
Cigarette lighter 262
Climate control system 176
Control panel 177
Defrosting, Front 181
Rear window defroster 175Clock 25, 130
Setting time 145, 146
Cockpit 22, 449
Cockpit Management and Data System
see COMAND
Cold tire inflation pressure 331
Collapsible wheel chock 386
COMAND* 449
COMAND* see separate COMAND
operating instructions
Combination switch 52, 122
Control system 130, 450
Multifunction display 130
Multifunction steering wheel 131
Resetting to factory default 140
Control system menu 130, 450
AUDIO 136
Menus overview 133
NAV* 138
Settings 140
Standard display 135
TEL* 157
Trip computer 155
Vehicle status message
memory 138