2006 MERCEDES-BENZ C280 engine

369 Practical hints
What to do if …
Symbol messagesDisplay symbol
Display message
Possible cause/consequence
Possible solution
#
Battery Alternator
Visit workshop
The battery is no longer charging.
Possible causes:

broken poly-V-belt


alternator malfunctioning

Stop immediately and check the
poly-V-belt in a safe location or as
soon as it is safe to do so.
If it is broken:

Do not continue to drive. Otherwise
the engine will overheat due to an
inoperative water pump which may
result in damage to the engine. Notify
an authorized Mercedes-Benz Center.
If it is intact:

Drive immediately to the nearest
authorized Mercedes-Benz Center.
Low voltage
Charge battery
The battery has insufficient voltage.

Start the engine (
page 48).
Low voltage
Consumers off

The battery has insufficient voltage.

Turn off unnecessary electrical
consumers.

370 Practical hintsWhat to do if …Display symbol
Display message
Possible cause/consequence
Possible solution
;
(USA only)
!
(Canada only)
Release
Parking brake
You are driving with the parking brake
set.

Release the parking brake
(page 50).
2
Brake wear
Visit workshop
The brake pads have reached their wear
limit.

Have the brake pads replaced as soon
as possible.
;
(USA only)
3
(Canada only)
Brake fluid
Visit workshop
There is insufficient brake fluid in the
reservoir.

Risk of accident! Stop the vehicle and
notify an authorized Mercedes-Benz
Center. Do not add brake fluid! This
will not solve the problem.
Warning!
G
Driving with the message
Brake fluid
Visit workshop.
displayed can result in
an accident. Have your brake system
checked immediately. Do not add brake
fluid before checking the brake system.
Overfilling the brake fluid reservoir can re-
sult in spilling brake fluid on hot engine
parts and the brake fluid catching fire. You
can be seriously burned.
!If you find that the brake fluid in the
brake fluid reservoir has fallen to the
minimum mark or below, have the
brake system checked for brake pad
thickness and leaks.
!Brake pad thickness must be visually
checked by a qualified technician at the
intervals specified in the Maintenance
booklet.

371 Practical hints
What to do if …
Display symbol
Display message
Possible cause/consequence
Possible solution
B
Coolant
Check level
The coolant level is too low.

Add coolant (
page 301).

If you have to add coolant frequently,
have the cooling system checked by
an authorized Mercedes-Benz Center.
Warning!
G
Do not spill antifreeze on hot engine parts.
Antifreeze contains ethylene glycol which
may burn if it comes into contact with hot
engine parts. You can be seriously burned.
!Do not ignore the low engine coolant
level warning. Extended driving with
the message and symbol displayed
may cause serious engine damage not
covered by the Mercedes-Benz Limited
Warranty.
Do not drive without sufficient amount
of coolant in the cooling system. The
engine will overheat causing major
engine damage.

372 Practical hintsWhat to do if …
During severe operating conditions and
stop-and-go city traffic, the coolant tem-
perature may rise close to 248°F (120°C).
Display symbol
Display message
Possible cause/consequence
Possible solution
•
Coolant
Stop, engine off!
The coolant is too hot.

Stop the vehicle in a safe location and
turn off the engine.

Only start the engine again after the
message disappears. You could
otherwise damage the engine.
Warning!
G
Driving when your engine is badly over-
heated can cause some fluids which may
have leaked into the engine compartment to
catch fire. You could be seriously burned.
Steam from an overheated engine can cause
serious burns and can occur just by opening
the hood. Stay away from the engine if you
see or hear steam coming from it.
Turn off the engine, get out of the vehicle
and do not stand near the vehicle until the
engine has cooled down.
!The engine should not be operated with
the coolant temperature above 248°F
(120°C). Doing so may cause serious
engine damage which is not covered by
the Mercedes-Benz Limited Warranty.

373 Practical hints
What to do if …
Display symbol
Display message
Possible cause/consequence
Possible solution
•
Coolant
Stop, engine off!
The poly-V-belt could be broken.

Stop the vehicle in a safe location and
immediately turn off the engine.

Check the poly-V-belt.
If it is broken:

Do not continue to drive. Otherwise the engine will
overheat due to an inoperative water pump which
may result in damage to the engine. Notify an au-
thorized Mercedes-Benz Center.
If it is intact:

Do not continue to drive the vehicle with this mes-
sage displayed. Doing so could result in serious
engine damage that is not covered by the
Mercedes-Benz Limited Warranty.

Observe the coolant temperature gauge in the in-
strument cluster (
page 24).

Drive immediately to the nearest authorized
Mercedes-Benz Center.
Coolant
Visit workshop.
The cooling fan for the coolant is
malfunctioning.

Observe the coolant temperature gauge in the in-
strument cluster (
page 24).

Have the fan replaced as soon as possible.

375 Practical hints
What to do if …
When the message
Check oil level at
next gas station appears while the en-
gine is running and at operating tempera-
ture, the engine oil level has dropped to
approximately the minimum level.
When this occurs, the warning will first
come on intermittently and then stay on if
the oil level drops further.Visually check for oil leaks. If no obvious oil
leaks are noted, drive to the nearest
service station where the engine oil should
be topped to the required level with an
approved oil specified in the Factory
Approved Service Products pamphlet.
Display symbol
Display message
Possible cause/consequence
Suggested solution
N
Check oil level
at next gas station
The engine oil has dropped to a critical
level.

Check the engine oil level
(page 299) and add oil as required
(page 300).

If you must add engine oil frequently,
have the engine checked for possible
leaks.!The engine oil level warnings should
not be ignored. Extended driving with
the symbol displayed could result in
serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.

406 Practical hintsFlat tire
Preparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.

Turn on the hazard warning flasher
(page 124).

Turn the steering wheel so that the
front wheels are in a straight ahead
position.

Set the parking brake (
page 58).

Move the gear selector lever toP
(manual transmission: to first or
reverse gear).

Turn off the engine (
page 59).

Remove the SmartKey from the starter
switch.

Have any passenger exit the vehicle at
a safe distance from the roadway.
Mounting the Minispare wheel
Preparing the vehicle
Prepare the vehicle as described
(page 406).

Take the wheel wrench, the wheel
bolts, and the jack out of the trunk
(page 383).

Take the Minispare wheel out of the
trunk (
page 386).
Warning!
G
The dimensions of the Minispare wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare wheel
mounted. Adapt your driving style accord-
ingly.
The Minispare wheel is for temporary use
only. When driving with Minispare wheel
mounted, ensure proper tire inflation
pressure and do not exceed a vehicle speed
of 50 mph (80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the Minispare
wheel replaced with a regular road wheel.
Never operate the vehicle with more than
one Minispare wheel mounted.
Do not switch off the ESP
® when a
Minispare wheel is mounted.
iOpen doors only when conditions are
safe to do so.

408 Practical hintsFlat tireThe jack take-up brackets are located
directly behind the front wheel housings
and in front of the rear wheel housings.
1Take-up bracket
2Jack
Place jack2 on firm ground.

Position jack2 under take-up
bracket1 so that it is always vertical
(plumb-line) as seen from the side,
even if the vehicle is parked on an
incline.

Jack up the vehicle until the wheel is a
maximum of 1.2 in (3 cm) from the
ground. Never start engine while
vehicle is raised.Removing the wheel
1Alignment bolt

Unscrew upper-most wheel bolt and
remove.

Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.

Remove the remaining bolts.

Remove the wheel.
Warning!
G
The jack is intended only for lifting the
vehicle briefly for wheel changes. It is not
suited for performing maintenance work
under the vehicle.

Never start the engine when the vehicle
is raised.


Never lie down under the raised vehicle.
!Do not place wheel bolts in sand or dirt.
This could result in damage to the bolts
and wheel hub threads.