2006 MAZDA MODEL RX 8 automatic transmission

Black plate (169,1)
Signal Warning/Indicator Lights Page
Door-Ajar Warning Light 5-45
Low Washer Fluid Level Warning Light 5-45
Automatic Transmission Warning Light 5-45
Tire Pressure Monitoring System Warning Light 5-45
KEY Warning Light (Red)/KEY Indicator Light (Green) 5-47
Security Indicator Light 5-48
Headlight High-Beam Indicator Light 5-49
Shift Position Indicator Light 5-49
TCS/DSC Indicator Light 5-50
DSC OFF Indicator Light 5-50
Cruise Main Indicator Light (Amber)/Cruise Set Indicator Light (Green) 5-50
Light-On Indicator Light 5-51
Power Steering Malfunction Indicator Light 5-51
Headlight Auto-Leveling Malfunction Indicator Light 5-51
Turn Signal/Hazard Warning Indicator Lights 5-51
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-39
RX-8_8U58-EA-05J_Edition1 Page169
Thursday, August 25 2005 4:55 PM
Form No.8U58-EA-05J

Black plate (175,1)
Once the beep sound is heard, it continues
sounding even if the vehicle speed lowers
to 20 km/h (12 mph) or less until the
seatbelt is fastened or the beep sound
period (90 seconds) has passed.
qDoor-Ajar Warning Light
This warning light comes on when any
door isn't securely closed.
qLow Washer Fluid Level
Warning Lightí
This warning light indicates that little
washer fluid remains. Add fluid (page
8-19).
qAutomatic Transmission Warning
Light
This warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
The light illuminates when the
transmission has a problem.
CAUTION
If the automatic transmission warning
light illuminates, the transmission has
an electrical problem. Continuing to
drive your Mazda in this condition
could cause damage to your
transmission. Consult an Authorized
Mazda Dealer as soon as possible.
qTire Pressure Monitoring System
Warning Lightí
This warning light illuminates for a few
seconds when the ignition switch is turned
to the ON position.
Thereafter, the warning light illuminates
when tire pressure is too low in one or
more tires, and flashes when there is a
system malfunction.
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-45íSome models. RX-8_8U58-EA-05J_Edition1 Page175
Thursday, August 25 2005 4:56 PM
Form No.8U58-EA-05J

Black plate (179,1)
The light stops flashing when the ignition
switch is turned to the ON position with
the correct ignition key.
At this time, the immobilizer system is
disarmed and the light illuminates for
about 3 seconds and then goes out.
If the engine doesn't start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
qHeadlight High-Beam Indicator
Light
This light indicates one of two things:
lThe high-beam headlights are on.
lThe turn signal lever is in the flash-to-
pass position.
qShift Position Indicator Light
(Automatic Transmission)
This indicates the selected shift position
when the ignition switch is in the ON
position.
Gear position indicator
Gear position indicator
When the shift lever is in the D or M
position, the numeral for the selected gear
displays.
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
5-49
RX-8_8U58-EA-05J_Edition1 Page179
Thursday, August 25 2005 4:56 PM
Form No.8U58-EA-05J

Black plate (253,1)
NOTE
lThe tire sealant cannot be reused.
Purchase new tire sealant at an
Authorized Mazda Dealer.
lThe emergency flat tire repair kit
cannot be used in the following
cases.
Consult an Authorized Mazda
Dealer.
lThe period of effective use for the
tire sealant has expired. (The
period of effectiveness is
indicated on the bottle label.)
lThe tear or puncture exceeds
about 4 mm (0.16 in).
lThe damage has occurred to an
area of the tire other than the
tread.
lThe vehicle has been driven with
nearly no air remaining in the tire.
lThe tire has come off the wheel
rim.
lDamage to the wheel rim has
occurred.
lThe tire has two or more
punctures.
qUsing the IMS Emergency Flat
Tire Repair Kit
1. Park on a level surface off the right-of-
way and set the parking brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine.
3. Turn on the hazard warning flasher.4. Unload passengers and luggage, and
remove the emergency flat tire repair
kit.
5. Shake the tire sealant well.
CAUTION
If the bottle is shaken after the injection
hose is screwed on, tire sealant could
spray out from the injection hose. Tire
sealant contacting clothing or other
objects may be impossible to remove.
Shake the bottle before screwing on the
injection hose.
In Case of an Emergency
Flat Tire
7-7
RX-8_8U58-EA-05J_Edition1 Page253
Thursday, August 25 2005 4:58 PM
Form No.8U58-EA-05J

Black plate (259,1)
NOTE
lMake sure the jack is well lubricated
before using it.
(With Tire Pressure Monitoring
System)
lBe sure to register the tire pressure
sensor ID signal code whenever tires
or wheels are changed (page 5-30).
1. Park on a level surface off the right-of-
way and firmly set the parking brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, and tool (page 7-3).
6. Block the wheel diagonally opposite
the tire to be changed. When blocking
a wheel, place a tire block both in front
and behind the tire.
NOTE
When blocking a tire, use rocks or
wood blocks of sufficient size to hold
the tire in place.
qRemoving the Tire
1. Loosen the lug nuts by turning them
counterclockwise one turn each, but
don't remove any until the tire has been
raised off the ground.
2. Place the jack under the jacking
position closest to the tire being
changed.
Jacking position
In Case of an Emergency
Flat Tire
7-13
RX-8_8U58-EA-05J_Edition1 Page259
Thursday, August 25 2005 4:59 PM
Form No.8U58-EA-05J

Black plate (264,1)
Overheating
If the temperature gauge indicates
overheating, the vehicle loses power, or
you hear a loud knocking or pinging
noise, the engine is probably too hot.
WARNING
Electrical Fan and Engine
Inspection:
Working near the electrical cooling
fan when it is running is dangerous.
You could be hit by the fan and
seriously injured. Turn off the ignition
switch and make sure the fan is not
running before attempting to work
near the electrical cooling fan.
Cooling System Cap:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury. Don't remove the cooling
system cap when the engine and
radiator are hot.
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
NOTE
Once the engine coolant exceeds a
preset temperature, an electrical cooling
fan turns on. It will continue running
for about 10 minutes after the ignition
switch is turned to off.
If the temperature gauge indicates
overheating:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transmission in park (P), a manual
transmission in neutral.
Apply the parking brake.
3. Turn off the air conditioner.
4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don't go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.
7-18
In Case of an Emergency
Overheating
RX-8_8U58-EA-05J_Edition1 Page264
Thursday, August 25 2005 4:59 PM
Form No.8U58-EA-05J

Black plate (270,1)
8. When finished, carefully disconnect the
cables in the reverse order described in
Step 6.
NOTE
Verify that the engine cover is securely
installed.
Push-Starting
WARNING
Towing a Vehicle to Start It:
Towing a vehicle to start it is
dangerous. The vehicle being towed
could surge forward when its engine
starts, causing the two vehicles to
collide. The occupants could be
injured. Never tow a vehicle to start it.
You can't start a vehicle with an automatic
transmission by pushing it.
CAUTION
Do not push-start a vehicle that has a
manual transmission. It can damage the
emission control system.
7-24
In Case of an Emergency
Emergency Starting
RX-8_8U58-EA-05J_Edition1 Page270
Thursday, August 25 2005 4:59 PM
Form No.8U58-EA-05J

Black plate (368,1)
Specifications
qEngine
Item Model
Type Rotary engine
Displacement 654 ml × 2 (654 cc × 2, 40.0 cu in × 2)
Compression ratio 10.0
qElectrical System
Item Classification
Battery 12V-52AH/5HR
Alternator 12 V - 100 A
Starter 12 V - 2.0 kW
Spark-plug numberTrailing side N3Y1 18 110, N3H1 18 110C
*1*2
Leading side N3Y8 18 110, N3Y9 18 110, N3H5 18 110*1*2
Spark-plug gap 1.15―1.25 mm (0.046―0.049 in)
*1 Standard
*2 ex factory
CAUTION
When cleaning the iridium plugs, do not use a wire brush. The fine particulate coating on
the iridium alloy and platinum tips could be damaged.
qLubricant Quality
Lubricant Classification
Engine oil Refer to the recommended SAE viscosity numbers on page 8-12.
Manual transmission oil API Service GL-4 (SAE 75W-90)
Automatic transmission fluid JWS3309
Rear differential oilAPI Service GL-5 (SAE 90)
API Service GL-5 (SAE 80W-90)
API Service GL-5 (SAE 75W-90)
*
Brake/Clutch fluid SAE J1703 or FMVSS116 DOT-3
* Not available from Mazda
10-4
Specifications
RX-8_8U58-EA-05J_Edition1 Page368
Thursday, August 25 2005 5:0 PM
Form No.8U58-EA-05J