2006 MAZDA MODEL MPV window

Black plate (180,1)
Operating Tips
qOperating the Climate Control
System
Operate the climate control system with
the engine running.
NOTE
To prevent the battery from being
discharged, do not leave the fan control
dial on for a long period of time with
the ignition switch in the ACC position
when the engine is not running.
qClearing the Air Inlet
Clear all obstructions like leaves, snow
and ice from the hood and the air inlet in
the cowl grille to improve the system
efficiency.
qFoggy Windows
The windows may fog up easily in humid
weather. Use the climate control system to
defog the windows.
To help defog the windows, operate the
air conditioner to dehumidify the air.
NOTE
The air conditioner may be used along
with the heater to dehumidify the air.
qOutside/Recirculated Air Position
Use the outside air position in normal
conditions. The recirculated air position
should be used only when driving on
dusty roads or for quick cooling of the
interior.
qParking in Direct Sunlight
If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then run
the climate control system.
qNot Using for a Long Period
Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
qCheck the Refrigerant before the
Weather Gets Hot
Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
efficient. Consult an Authorized Mazda
Dealer for refrigerant inspection.
The air conditioner is filled with
HFC134a (R134a), a refrigerant that will
not damage the ozone layer.
If the air conditioner is low on refrigerant
or has a malfunction, consult an
Authorized Mazda Dealer.
qReplacement of the Cabin Air Filter
If your vehicle is equipped with an air
filter for the air conditioner, it is necessary
to change the filter periodically as
indicated in scheduled maintenance (page
8-3). Consult an Authorized Mazda
Dealer for replacement of the cabin air
filter.
6-2
Interior Comfort
Climate Control System
Mazda MPV_8U61-EA-05G_Edition1 Page180
Tuesday, June 21 2005 9:35 AM
Form No.8U61-EA-05G

Black plate (185,1)
WARNING
The Recirculated Air Position:
Using the
position in cold or
rainy weather will cause the windows
to fog up. Your vision will be
hampered, which could lead to a
serious accident. Do not use the
position in cold or rainy weather.
qHeating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidified heating is desired, turn
on the air conditioner.
NOTE
lIf the windshield fogs up easily, set
the mode selector dial to the
position.
lIf cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
qCooling (With Air Conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. Adjust the fan control dial and
temperature control dial to maintain
maximum comfort.
CAUTION
When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-22).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner off
(page 7-16).
Interior Comfort
Climate Control System
6-7
Mazda MPV_8U61-EA-05G_Edition1 Page185
Tuesday, June 21 2005 9:35 AM
Form No.8U61-EA-05G

Black plate (186,1)
NOTE
lWhen maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the
position,
then set the fan control dial to
position 4.
lIf warmer air is desired at floor level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
qVentilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
qWindshield Defrosting and Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position.
3. Set the fan control dial to the desired
speed.
WARNING
Foggy Windshield:
Using the
position with the
temperature control set to the cold
position will cause the outside of the
windshield to fog up. Your vision will
be hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the
position.
NOTE
lFor maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
lIf warm air is desired at the floor, set
the mode selector dial to the
position.
lIn the,orposition, the air
conditioner is automatically turned
on (however, the indicator light does
not illuminate) and the
position
is automatically selected to defrost
the windshield.
In the
orposition, the
position cannot be changed to
the
position.
qDehumidifying (With Air
Conditioner)
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector dial to the
desired position.
6-8
Interior Comfort
Climate Control System
Mazda MPV_8U61-EA-05G_Edition1 Page186
Tuesday, June 21 2005 9:35 AM
Form No.8U61-EA-05G

Black plate (282,1)
2. Separate the air cleaner housing and
remove the filter.
Air filterAir cleaner housing
3. Wipe inside the air cleaner housing
with a damp cloth.
4. Clean or replace the filter.
5. Install in the reverse order of removal.
Replace the filter according to Scheduled
Maintenance (page 8-3).
Wiper Blades
CAUTION
lHot waxes applied by automatic car
washers have been known to affect
the wiper's ability to clean windows.
lTo prevent damage to the wiper
blades, don't use gasoline, kerosene,
paint thinner, or other solvents on or
near them.
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
qReplacing Windshield Wiper Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION
To prevent damage to the wiper arms
and other components, don't try to
sweep the wiper arm by hand.
8-22
Maintenance and Care
Owner Maintenance
Mazda MPV_8U61-EA-05G_Edition1 Page282
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (284,1)
4. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
NOTE
Install the blade so that the tabs are
toward the bottom of the wiper arm.
qReplacing Rear Window Wiper
Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm
and other components, don't try to
sweep the wiper arm by hand.1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
Plastic locking clip
CAUTION
To prevent damage to the rear window
let the wiper arm down easily, don't let
it slap down on the rear window.
2. Pull down the blade rubber and slide it
out of the blade holder.
8-24
Maintenance and Care
Owner Maintenance
Mazda MPV_8U61-EA-05G_Edition1 Page284
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (301,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
1 DEFOG 40A Rear window defroster
2 BTN 60A STOP, HAZARD, ROOM, D.LOCK and DRL fuses
3 ABS 60A Antilock brake system
í, For protection of various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEAT 30A Rear heater
í, For protection of various circuits
8 IG KEY2 40A A/C, P.WINDí, MOONROOFíand R.WIP fuses
9 A/C 10A Air conditioner, For protection of various circuits
10 TAIL 15A Taillights
11 AC PWR 15A Inverter
12 HORN 15A Horn
13 FOG 15A For protection of various circuits
14 EEC 5A For protection of various circuits
15 HEAD L 15A Headlight-left
16 HEAD R 15A Headlight-right
17 HID L 20A―
Maintenance and Care
Owner Maintenance
8-41íSome models. Mazda MPV_8U61-EA-05G_Edition1 Page301
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (302,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
18 HID R 20A―
19 IG KEY1 60A METER, ENGINE and WIPER fuses
20 EGI INJ 30A For protection of various circuits
21 FUEL PUMP 20A Fuel pump
22 MAIN 120A For protection of all circuits
Fuse block (Driver's side)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
1 P.WIND 40A Power windows
í, For protection of various circuits
2 WIPER 20A Windshield wipers and washer
3 SUN ROOF 15A Moonroof
í, For protection of various circuits
4 R.WIP 10A Rear window wiper and washer
5 SEAT 20A For protection of various circuits
6 M.DEF 10A Mirror defroster
í, For protection of various circuits
7 A/C 10A Air conditioner, For protection of various circuits
8 DRL 10A For protection of various circuits
9―― ―
10 H/CLEAN 20A For protection of various circuits
11―― ―
8-42
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8U61-EA-05G_Edition1 Page302
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G

Black plate (303,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
12 HAZARD 10A Hazard warning flashers
13 ROOM 15A Overhead lights, Map lights, Luggage compartment light
14 AUX POWER 25A Accessory socket
15 CLOSER LH 20A For protection of various circuits
16 AUDIO 10A Audio system, For protection of various circuits
17 D.LOCK 30A Power door locks
í, For protection of various circuits
18 P/SEAT 30A Power seatí
19 ENGINE 10A Engine control system
20 METER 10A Instrument cluster
21 STOP 15A Brake lights
22 CLOSER RH 20A For protection of various circuits
23 ACC.DELAY 30A Power windows delay, For protection of various circuits
24 METER 15A Instrument cluster, INH switch
25 ST.SIGN 10A Starter signal
26 CIGAR 25A Lighter
27―― ―
28―― ―
Maintenance and Care
Owner Maintenance
8-43íSome models. Mazda MPV_8U61-EA-05G_Edition1 Page303
Tuesday, June 21 2005 9:38 AM
Form No.8U61-EA-05G