2006 MAZDA MODEL 6 lights

Black plate (316,1)
(Sport Wagon)
1. Remove the liftgate upper trim and
high-mount brake light component.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
License plate lights
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the lens and
remove the lens by carefully prying on
the edge of the lens.2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
qReplacing Interior Light Bulbs
Overhead light/Map lights (Withoverhead console)
1. Remove the screws.
2. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
8-50
Maintenance and Care
Owner Maintenance
Mazda6_8U66-EA-05F_Edition1 Page316
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F

Black plate (317,1)
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.
Overhead light/Map lights (Withoutoverhead console)
1. Wrap a flathead screwdriver with a soft
cloth to prevent damage to the trim and
gently insert it in the overhead light as
shown in the figure, and then remove
the overhead light unit.
2. Turn the socket and bulb assembly
counterclockwise and remove it.3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
Courtesy lights, Vanity mirror lights,and Luggage compartment light
1. Wrap a small flathead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens.
2. Disconnect the bulb by pulling it out.
Edge Courtesy lights
Maintenance and Care
Owner Maintenance
8-51
Mazda6_8U66-EA-05F_Edition1 Page317
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F

Black plate (318,1)
Vanity mirror lights
Edge (Type A)
Edge
Vanity mirror lights
(Type B)
(5-Door)Luggage compartment light
Luggage compartment light
(Sport Wagon)
Edge
3. Install the new bulb in the reverse order
of removal.
Trunk light (Sedan)
1. Press both sides of the lens cap to
remove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.
8-52
Maintenance and Care
Owner Maintenance
Mazda6_8U66-EA-05F_Edition1 Page318
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F

Black plate (319,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's sidekick-panel
If the electrical system doesn't work, first
inspect fuses on the driver's side kick-
panel.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover by sliding
the cover straight back toward you.
CAUTION
Pulling the cover off sideways may
break the retaining tabs off.3. Pull the fuse straight out with the fuse
puller provided on the fuse block
located in the engine compartment.
4. Inspect it and replace if it's blown.
NormalBlown
5. Push in a new fuse of the same
amperage rating, and make sure it fits
tightly. If it doesn't, have an Authorized
Mazda Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
WARNING
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Maintenance and Care
Owner Maintenance
8-53
Mazda6_8U66-EA-05F_Edition1 Page319
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F

Black plate (320,1)
Replacing the fuses under the hood
If the headlights or other electrical
components don't work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
oneof the same amperage rating.
Normal
Blown
NOTE
To replace the MAIN fuse, contact an
Authorized Mazda Dealer (page 8-55).
8-54
Maintenance and Care
Owner Maintenance
Mazda6_8U66-EA-05F_Edition1 Page320
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F

Black plate (321,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
1 SPARE――
2 SPARE――
3 SPARE――
4 M.DEF 7.5A Mirror defroster
í
5―― ―
6 INJ 15A Injector
7 ENG BAR10A
*1Air flow sensor, EGR control valve
15A*2
8―*1――
ENG BB*25A Cooling fan
9 HEAD LR 15A Headlight-low beam (Right)
10 HEAD LL 15A Headlight-low beam (Left)
11 HEAD HL 10A Headlight-high beam (Left)
12 HEAD HR 10A Headlight-high beam (Right)
13 ETC 7.5A Accelerator position sensor
14 HAZARD 10A Turn signal lights
15 STOP 20A Brake/Horn
Maintenance and Care
Owner Maintenance
8-55íSome models. Mazda6_8U66-EA-05F_Edition1 Page321
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F

Black plate (322,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
16 TCM15A
*1TCM
10A*2
17 ENG+B 7.5A PCM, TCM
18 FUEL PUMP 15A Fuel pump
19 IG KEY1 30A Engine control unit, Lighter
20 P.WIND 30A Power window
21―― ―
22 DRL 20A DRL
23―― ―
24 BLOWER 40A Blower motor
25 BTN 40A Overhead light, Power door lock
26 IG KEY2 40ARear wiper motor
í, Heater control unit, Windshield wiper and
washer
27 DEFOG 40A Rear window defroster
28 ABS 60A ABS
í
29AD FAN*130A Cooling fan
FAN2*2
30FA N*130A Cooling fan
FAN1*2
31 TAIL 10A Taillights, License plate lights, Parking lights
32 ILLUMI 10A Dashboard illumination
33 MAG 10A Magnet clutch
34 AUDIO 15A Audio system
35 P.SEAT 30A Power seat
í
36 OPENER 7.5A Trunk opener motorí
37―― ―
38―*1――
IG1*215A CAT SSR
39 FOG 15A Fog lightsí
40 MAIN 120A For protection of all circuits
*1 2.3-liter engine
*2 3.0-liter engine
8-56
Maintenance and Care
íSome models.
Owner Maintenance
Mazda6_8U66-EA-05F_Edition1 Page322
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F

Black plate (380,1)
qWeights
Specification Item Weight
2.3-liter engineGVWR (Gross Vehicle Weight Rating) 1,940 kg (4,279 lbs)
GAWR (Gross Axle Weight Rating)Front 1,005 kg (2,216 lbs)
Rear 936 kg (2,064 lbs)
3.0-liter engineGVWR (Gross Vehicle Weight Rating) 2,052 kg (4,526 lbs)
GAWR (Gross Axle Weight Rating)Front 1,084 kg (2,390 lbs)
Rear 968 kg (2,136 lbs)
qAir Conditioner
Gas complies with SAE J639 Maximum operating charge
HFC134a (R-134a) 0.5 kg (17.6 oz)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage ECER SAE
HeadlightsHigh beam 55 H1―
Low beamHalogen 55 H1―
Xenon
fusion35 D2S―
Front turn signal lights 27―#2357A
Parking lights 5 W5W―
Fog lights
í55 H11 H11
Side-marker lights 5 W5W―
High-mount brake lightSedan 18.4 W16W #921
5-Door/Sport Wagon 21 W21W #7440
Rear turn signal lightsSedan/5-Door 21 WY21W―
Sport Wagon 21 W21W #7440
Brake lights/Taillights 21/5 W21/5W #7443
Taillights 5
*1W21/5W #7443
Reverse lights 18.4 W16W #921
License plate lights 5 W5W―
*1 Use a 21/5W type bulb.
10-6íSome models.
Specifications
Mazda6_8U66-EA-05F_Edition1 Page380
Friday, June 3 2005 8:49 AM
Form No.8U66-EA-05F