2006 LEXUS LX470 sensor

STEERING WHEEL AND MIRRORS
196
INSIDE REAR VIEW MIRROR
16X016e
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between “AUTO”
and “DAY”.
The indicator comes on when the “AUTO” mode is selected.
“DAY” mode: The mirror surface is normal.
“AUTO” mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the “AUTO” mode. When
the inside air temperature is low, it may take a little longer
for the mirror to darken in response to the detection of
headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the driver to mishandle the vehicle
and an accident may occur resulting in death or serious
injuries.
16x658b
To ensure correct functioning of antiglare mirror sensors
located on both sides of the mirror, do not touch or cover
the sensors with your finger or a piece of cloth, etc.

STEERING WHEEL AND MIRRORS
198
NOTICE
Do not put magnets or a metal object near the inside rear
view mirror. Doing this may cause malfunction of the
compass sensor.
CALIBRATING THE COMPASS (deviation calibration)
The direction display on the compass deviates from the true
direction determined by the earth’s magnetic field. The
amount of deviation varies according to the geographic
position of the vehicle.
To adjust for this deviation, stop the vehicle and push the
button for longer than about 6 seconds until the number (1 −15)
appears on the display. Then push the button again, referring
to the following map to select the number of the zone where the
vehicle is.
16x657
 Zone number
If the direction is displayed several seconds after adjustment,
the calibration is finished.

AIR CONDITIONING
207
If manual switching of air intake is desired
20X023a
Each time you push the air intake control button, the mode
changes in order from the RECIRCULATED AIR mode to
AUTOMATIC mode to OUTSIDE AIR mode, then back to the
RECIRCULATED
AIR mode. Each indicator light shows which
mode is now selected.
1 RECIRCULATED mode If quick circulation of cooled air
is desired, select this mode.
2 EXHAUST GAS AUTOMATIC mode If the outside air
contains harmful substances like exhaust gas (i.e., when
the vehicle running just in front of your vehicle accelerates
rapidly), the system changes automatically from the
OUTSIDE AIR mode (with indicators
2
and 3 on) to
the RECIRCULATED mode (with indicators 1
and 2
on).
3 OUTSIDE AIR mode The system will take fresh outside
air into the vehicle. Turning off the air conditioning manually will cancel the
EXHAUST
GAS AUTOMATIC mode. If you select the “AUTO”
mode during fan operating, the air conditioning turns on and
the EXHAUST GAS AUTOMATIC mode will operate.
For normal use, it is best to keep the air intake control button
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.
In the following cases, the RECIRCULATED mode may
change to the OUTSIDE AIR mode automatically to prevent
interior fog.
 When the outside temperature becomes lower than 4 C
(39 F).
 When the air conditioning compressor malfunctions.
 When the air conditioning cooler refrigerant decreases.
To change the sensitivity of the sensor switching between
the RECIRCULA TED and OUTSIDE AIR in the AUTOMATIC
mode, push the air intake control button until the “AUTO”
indicator light flashes. The display changes as illustrated
below.
The sensitivity of the sensor can be adjusted only while the
vehicle has stopped.

STARTING AND DRIVING
273
While the
system is on, pushing the knob turns off the “MAIN”
indicator light and the system. If you turn the ignition off with
the system turned on, the system will be turned off
automatically.
CAUTION
If the image in the headup display (night view display)
is too bright, you cannot see the surroundings through
the windshield clearly. To avoid glare, do not make the
display brighter than necessary.
31x533c
 1 Nearinfrared floodlight (Night view projector)
2Nearinfrared camera (Night view camera)
3Headup display (Night view display)
4Automatic light control sensor
The nearinfrared floodlight (night view projector which
irradiates nearinfrared light not seen by people) located
near the fog lights irradiates the area reaching from the tip
of the low beam to high beam. The nearinfrared camera
(night view camera) located on top of the windshield
converts irradiated light into an image. This image is
shown on the headup display (night view display)
located on the bottom of the windshield.
The automatic light control sensor is on top of the passenger
side instrument panel.
Do not place anything on the instrument panel and do not affix
anything on the windshield to block this sensor.