2006 LEXUS LX470 traction control

STARTING AND DRIVING
268If the indicator light does not go off when you push out the
center differential lock button, drive straight ahead while
accelerating or decelerating, or drive in reverse.
See “(b) Shifting procedure” for further instructions.
Advice for driving on slippery roads in “L” (low speed
position) mode
If you shift the four
−wheel drive control lever to “L”, the
automatic transmission lever to “2” when you drive in steep
off −road areas, the output of the brake can be controlled
effectively by the active traction control system, which assists
the driver to control the driving power of 4 wheels.
Use the “L” position of the automatic transmission lever for
maximum power and traction when your wheels get stuck or
when you drive down a steep incline. In the following cases,
the out put of the brake can be controlled by the active traction
control system if the engine speed is under 3,000 rpm
(normally engine speed is under 3,000 rpm when the wheels
get unstuck).
 The four− wheel drive control lever in the “L” position and the
automatic transmission lever in the “L” position or the
automatic transmission lever in the “D”, “4”, “3” or “2” \
with
the transmission downshifting to the first gear
 The four− wheel drive control lever in the “L” position and the
automatic transmission lever in the “R” position
(As for the automatic transmission lever positions, see
“Automatic transmission” on page 259.)
(b) Shifting procedure
To shift between unlock and lock modes in “H”, push the
center differential lock button.
To shift between unlock and lock modes in “L”, push the
center differential lock button.
To shift between “H” and “L”, stop the vehicle, put the
transmission into “N” and move the four −wheel drive control
lever.
CAUTION
Never move the fourwheel drive control lever if wheels
are slipping. Stop the slipping or spinning before
shifting.
NOTICE
For normal driving on dry and hard surface roads,
unlock the center dif ferential. To prevent damage to the
center differential lock system, do not push the center
differential lock button when the vehicle is cornering or
when its wheels are spinning freely of f the ground. If the
indicator light does not go off when unlocking the
center differential, drive straight ahead while
accelerating or decelerating, or drive in reverse.

STARTING AND DRIVING
282
Before you lower the vehicle height with the height
select switch, check under the vehicle to make sure
that nothing to damage the vehicle or no one to be
injured is there and the underbody of the vehicle
does not touch the ground.
 After unloading, the height of a vehicl e equipped with
the active height control suspension becomes
slightly higher than the normal vehicle height. Take
sufficient care where the overhead height is
restricted.
The vehicle height cannot be raised if the vehicle load
exceeds the following limits:
 Up to 4 occupants* plus about 300 kg (661 lb.) in the normal
mode
 Up to 4 occupants* plus about 170 kg (375 lb.) in the high
mode
*About 68 kg (150 lb.) for a person
If the above load capacity is exceeded, the desired vehicle
height may not be obtained even if the height select switch is
pushed. (If the vehicle height cannot be raised in the normal
mode and the height control indicator indicates “LO”, this is
because the vehicle is loaded too heavily. Under these
conditions, drive your vehicle with due care.)
If the vehicle height cannot be raised even after unloading,
push the height select switch on the “
” side and then on the
“ ” side. If this does not work, turn off the ignition once and
then turn on. Operate the select switch again. If the vehicle height is adjusted on the slope, or with the
selector lever in a position other than “P” or “N” while the\
vehicle is stopped, you may h
ear a sound caused by the
expansion and contraction of the propeller shaft.
 Selecting the high mode:
Push the height select switch on the “ ” side when the vehicle
speed is under about 30 km/h (19 mph).
To change the normal mode to high, push the switch once.
To change the low mode to high, push the switch twice. It
takes about 30 seconds until the low mode changes to the high
mode.
 Selecting the normal mode:
To change the high mode to normal, push the height select
switch on the “
” side once.
To change the low mode to normal, push the height select
switch on the “ ” side once.
 Selecting the low mode:
Push the height select switch on the “
” side while the vehicle
is stopped.
To change the high mode to low, push the switch twice.
To change the normal mode to low, push the switch once.

STARTING AND DRIVING
288When your vehicle is loaded heavily or you are driving in an
unpaved
road, the mode
3
or 4 will be recommended. To
provide good vehicle stability, the damping effect will be harder
than for ordinary driving mode.
With the four−wheel drive control lever at “L”, the damping
effect suitable for off −road driving will be provided.ACTIVE TRACTION CONTROL
SYSTEM
31X518a
Active traction control system indicator light
The active traction control system automatically helps
control the spinning of 4 wheels which may occur when
accelerating on slippery road surfaces, by controlling the
output of the brake and engine. Thus, the system assists
driver to control the driving power of 4 wheels. When you
turn the ignition switch on, the active traction control
system always turns on automatically, and the active
traction control indicator light will come on. The indicator
light will go off after a few seconds.
When active traction control is applied, the active traction
control system indicator light blinks.

STARTING AND DRIVING
289
You may hear a sound in the engine compartment for a few
seconds when the engine is started or just after the vehicle
begins to move. This means that the active traction control
system is in the self
−check mode, and does not indicate
malfunction. When the active traction control system is
operating, you may feel vibration or hear noise of your vehicle,
caused by operation of the brakes. This indicates the system
is functioning properly.
When getting the vehicle out of mud or newly fallen snow, etc.,
the active traction control system will help operate to prevent
the wheels from spinning.
31X503
 Active traction control system failure warning
This light warns when there is a problem somewhere in the
active traction control system or vehicle stability control
system.
If the “VSC/TRAC” warning light comes on, have your vehicle
checked by your Lexus dealer as soon as possible. The brake actuator temperature increases during the active
traction control system or vehicle stability control system
operating. If the brake actuator temperature becomes too high
while the active traction cont
rol system or vehicle stability
control system is operating, a buzzer will start to sound
intermittently to indicate that the active traction control system
can no longer operate. In this case, immediately stop your
vehicle at a safe place. If the system continues to operate, the
buzzer sound changes from intermittent to continuous. (The
continuous buzzer sound will stop after about 3 seconds.) At
the time the “VSC/TRAC” warning light will come on and the
active traction control system temporarily stops operating in
order to protect the brake actuator. (Although the active
traction control system does not operate, there is no problem
to continue your driving.) The system will be automatically
restored after a short time and “VSC/TRAC” warning light goes
off if the accelerator pedal is released.
When the “ABS” warning light comes on, the active traction
control system is not operating.
The “VSC/TRAC” warning light will come on when the ignition
key is turned to “ON”, and will go off after a few seconds.
The “VSC/TRAC” warning light may stay on for 60 seconds
after the ignition key is turned to the “ON” position. It is normal
if it goes off after a few seconds.
Depressing the brake pedal repeatedly may turn on the
“VSC/TRAC” warning light. It is normal if it goes off after a few
seconds.
When the “VSC/TRAC” warning light comes on, the active
traction control system is not operating, but there is no problem
if you continue to drive.

STARTING AND DRIVING
290In the following cases, contact your Lexus dealer:

The “VSC/TRAC” warning light does not come on after the
ignition is turned to on.
 The “VSC/TRAC” remains on after the ignition is turned to
on.
CAUTION
Under certain slippery road conditions, full traction of
the vehicles and power to 4 wheels may not be
maintained, even though the active traction control
system is in operation. Do not drive the vehicle under
any speed or maneuvering conditions which will cause
the vehicle to lose traction. In situations where the road
surface is covered with ice or snow, your vehicle should
be fitted with snow tires or tire chains. Always drive at
an appropriate and cautious speed for the road
conditions present.
VEHICLE STABILITY CONTROL SYSTEM
31X504
The vehicle stability control system helps provide
integrated control of the systems such as antilock
brakes, traction control, engine control, etc. This system
automatically controls the output of the brakes or engine
to help prevent the vehicle from skidding under adverse
conditions.
When you turn the ignition switch on, the slip indicator light will
come on. The slip indicator light will go off after a few seconds.
If the vehicle is going to skid during driving, the slip indicator
light flashes and an alarm sounds intermittently.

STARTING AND DRIVING
291
The vehicle stability control system is activated when the
vehicle speed is about more than 15 km/h (9 mph).
You may hear a sound in the engine compartment for a few
seconds when the engine is started or just after the vehicle
begins to move. This means that the vehicle stability control
is in the self−
check mode and does not indicate a malfunction.
31X529
Pushing the center differential lock button automatically turns
the vehicle stability control system off. At this time, the “VSC
OFF” indicator comes on with the center differential lock
indicator light. (For details, see “Four −wheel drive system” on
page 266.)
31x505
 Vehicle stability control system failure warning
These lights warn when there is a problem somewhere in the
vehicle stability control system or active traction control
system.
If the “VSC/TRAC” warning light and “VSC OFF” indicator light
come on, have your vehicle checked by your Lexus dealer as
soon as possible. However, there is no problem even if the
“VSC/TRAC” warning light comes on when the brake actuator
temperature becomes high. (For details, see “Active traction
control system” on page 288.)
When the “ABS” warning light comes on, the vehicle stability
control system is not operating.
The lights will come on when the ignition key is turned to “ON”,
and will go off after a few seconds.
The lights may stay on for 60 seconds after the ignition key is
turned to the “ON” position. It is normal if they go off after a few
seconds.

STARTING AND DRIVING
292Depressing
the brake pedal repeatedly may turn on the lights.
It is normal if they go off after a few seconds.
When the “VSC/TRAC” warning light and “VSC OFF” indicator
light come on, the vehicle stability control system is not
operating, but there is no problem if you continue to drive.
In the following cases, contact your Lexus dealer:
 The “VSC/TRAC” warning light, “VSC OFF” indicator light
and slip indicator light do not come on after the ignition is
turned to on.
 The “VSC/TRAC” warning light and “VSC OFF” indicator
light remain on after the ignition is turned to on.
 The “VSC OFF” indicator light comes on while driving
without pushing the center differential lock switch.
CAUTION
Active traction control system, vehicle stability
control system and antilock brake system are
electronic systems designed to help the driver
maintain control under adverse conditions. They are
not a substitute for safe driving practices. Factors
including speed, road conditions and driver steering
input can all affect whether active traction control
system, vehicle stability control system and
antilock brake system will be effective in preventing
a loss of control. Always keep safety driving in mind.
If the slip indicator light flashes, sounding an alarm,
special care should be taken while driving.
 Only use tires of specified size. The size,
manufacturer, brand and tread pattern for all 4 tires
should be the same. If you use the tires other than
specified, or different type or size, the vehicle
stability control system may not function correctly.
When replacing the tires or wheels, contact your
Lexus dealer. (See “Checking and replacing tires” on
page 438.)

STARTING AND DRIVING
297
Driving over the steps such as the joints on the road.
 Driving on roads where the road surface is pitted or
has other differences in surface height.
Install all 4 tires of specified size at appropriate
pressure: The antilock brake system detects vehicle
speeds using the speed s ensors for respective wheels’
turning speeds. The use of tires other than specified
may fail to detect the accurate turning speed resulting
in a longer stopping distance.“ABS” warning light
31X506
The light comes on when the ignition key is turned to the “ON”
position. If the anti−lock brake system and the brake assist
system work properly, the light turns off after a few seconds.
Thereafter, if either of the systems malfunctions, the light
comes on again.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti−lock brake system, the brake
assist system, the active traction control system and/or the
vehicle stability control system do/does not operate, but the
brake system still operates conventionally.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti− lock brake system does not
operate so that the wheels could lock up during a sudden
braking or braking on slippery road surfaces.