2006 LEXUS LX470 heating

SWITCHES
44
SEAT HEATER SWITCHES
12X025c
 1For driver’s seat 2For front passenger’s seat
3High heating temperature
4Low heating temperature
To turn on the seat heater, push the switch to “HI” (high
temperature) or “LO” (low heating temperature). To turn
off the seat heater, push the switch lightly on the opposite
side. At this time, the indicator light on either side will
illuminate to indicate the seat heater is operating.
The ignition key must be in the “ON” position to operate seat
heaters.
CAUTION
Occupants must use caution when operating the seat
heater because they may experience minor burns even
at low temperatures. Use extra caution for;
 Babies, small children, elderly persons, sick persons
or persons with physical disabilities
 Persons who have sensitive skin
 Persons who are exhausted
 Persons who have taken alcohol or drugs which
induce sleep (sleeping drug, cold remedy, etc.).
To prevent the seat from overheating, do not use the
seat heater with a blanket, cushion, or other insulating
objects which cover the seat.
NOTICE
 Do not put unevenly weighted objects on the seat and
do not stick sharp objects (needles, nails, etc.) into
the seat.
 When cleaning the seats, do not use organic
substances (paint thinner, benzine, alcohol,
gasoline, etc.). They may damage the heater and seat
surface.
 To prevent the battery from being discharged, turn
the switches off when the engine is not running.

INTERIOR EQUIPMENT
72
OUTSIDE TEMPERATURE DISPLAY
14X501
This display shows the outside temperature when the
ignition switch is on.
The displayed temperature ranges from −30C (− 22F) up to
50 C (122F). If the temperature does not appear on the
display or it shows “− − ”, take your vehicle to your Lexus dealer.
When the headlight switch is in the first or second click stop,
you can also adjust the brightness of the display using the
instrument panel light control dial.
The unit shown on the display can be changed. For details,
see “Trip information display” on page 63.
CIGARETTE LIGHTER AND ASHTRAY
Front
14X006c
To use the cigarette lighter, press in the cigarette lighter.
After it finishes heating up, it automatically pops out ready
for use.
Do not hold the cigarette lighter pressed in.
If the engine is not running, the ignition key must be in the
“ACC” position to use the lighter.
When finished with your cigarette, thoroughly extinguish it in
the ashtray to prevent other cigarette butts from catching fire.
After using the ashtray, close the lid completely.
To remove the ashtray, press down on the lock spring plate and
pull out.
Use a Lexus genuine cigarette lighter or equivalent for
replacement.

AIR CONDITIONING
206SETTING OPERATION manual control
When one of the manual control buttons is depressed
while operating in automatic mode, the mode relevant to
the depressed button is set. Other conditions continue to
be adjusted automatically.
If manual air flow selection is desired
20X021a
The outlets from which air is delivered can be selected
manually by pressing the button. The function of each mode
is as follows:
1
Panel − Air flows mainly from the instrument panel vents.
2
Bilevel − Air flows from both the floor vents and the
instrument panel vents.
3 Floor − Air flows mainly from the floor vents.
It is recommended that you close the lower vent. For details
about this, see page 212.
4 Floor/Windshield − Air flows mainly from the floor vents
and windshield vents.
It is recommended that you close the lower vent. For details
about this, see page 212.
If quick heating or cooling is desired
Turn the “TEMP” knob until “MAX. HOT” or “MAX. COLD”
appears on the display.
If manual fan speed control is desired
21x600
 1 Fan speed at low 2Fan speed at high
The fan speed can be set to your desired speed by pushing the
appropriate side of fan speed control button. The higher the
fan speed is, the more air is delivered. Pushing the “OFF”
button turns off the fan.
To remove exterior windshield frost, use the high speed
setting.

AIR CONDITIONING
207
If manual switching of air intake is desired
20X023a
Each time you push the air intake control button, the mode
changes in order from the RECIRCULATED AIR mode to
AUTOMATIC mode to OUTSIDE AIR mode, then back to the
RECIRCULATED
AIR mode. Each indicator light shows which
mode is now selected.
1 RECIRCULATED mode If quick circulation of cooled air
is desired, select this mode.
2 EXHAUST GAS AUTOMATIC mode If the outside air
contains harmful substances like exhaust gas (i.e., when
the vehicle running just in front of your vehicle accelerates
rapidly), the system changes automatically from the
OUTSIDE AIR mode (with indicators
2
and 3 on) to
the RECIRCULATED mode (with indicators 1
and 2
on).
3 OUTSIDE AIR mode The system will take fresh outside
air into the vehicle. Turning off the air conditioning manually will cancel the
EXHAUST
GAS AUTOMATIC mode. If you select the “AUTO”
mode during fan operating, the air conditioning turns on and
the EXHAUST GAS AUTOMATIC mode will operate.
For normal use, it is best to keep the air intake control button
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.
In the following cases, the RECIRCULATED mode may
change to the OUTSIDE AIR mode automatically to prevent
interior fog.
 When the outside temperature becomes lower than 4 C
(39 F).
 When the air conditioning compressor malfunctions.
 When the air conditioning cooler refrigerant decreases.
To change the sensitivity of the sensor switching between
the RECIRCULA TED and OUTSIDE AIR in the AUTOMATIC
mode, push the air intake control button until the “AUTO”
indicator light flashes. The display changes as illustrated
below.
The sensitivity of the sensor can be adjusted only while the
vehicle has stopped.

AIR CONDITIONING
208
20X062d
When you turn the “TEMP” knob, the sensitivity changes from
“+3” down to “−3”. If you do not operate any button for a few
seconds or if you push a button other than the air intake control
button and temperature control knob, the previous display
returns.
If manual onoff of the air conditioning is desired
Push the “A/C” button to turn the air conditioning on and push
it again to turn the air conditioning off. If you turn off the air
conditioning manually, the EXHAUST GAS AUTOMATIC
mode will be cancelled.
If the outside temperature is lowered down to around 0 C
(32 F), the air conditioning will turn off automatically. At this
time, the indicator on the A/C button is off and the EXHAUST
GAS AUTOMATIC indicator light remains on. However, the
EXHAUST GAS AUTOMA TIC mode does not operate. When
the air conditioning turns on as with the raised temperature, the
EXHAUST GAS AUTOMATIC mode resumes. If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off
once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year −round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the “A/C” button will blink. If the indicator of the
“A/C” button blinks even when the “A/C” button is pushed
again, have the compressor checked by your nearest Lexus
dealer.

AIR CONDITIONING
209
(b) Windshield defogging and defrosting
20X024b
To remove interior fog on the windshield
Push the windshield air flow button.
To remove frost or exterior fog on the windshield
1. Place the temperature control lever at the maximum
temperature.
2. Push the windshield air flow button.
3. Push the “HI” button of the fan speed control button to obtain
a maximum air flow.
4. Leave the air conditioning on −off button off.
For further information for removing frost and fog, see “Lower
vent” on page 212.
When the windshield air flow button is pushed while operating,
the OUTSIDE AIR mode is set. Push
the “A/C” button for dehumidified heating or cooling. This
setting clears the front view more quickly.
Pushing this button once again returns the air flow mode to the
last one used.
CAUTION
Do not use the windshield air flow button during cooled
air operation in extremely humid weather. The
difference between the temperature of the outside air
and that of the windshield could cause the outer surface
of the windshield to fog up blocking your vision.

STARTING AND DRIVING
255

To ensure that the threeway catalytic converter and
the entire emission control system operate properly,
your vehicle must receive the periodic inspections
required by the Lexus Maintenance Schedule. For
scheduled maintenance information, refer to the
“Owner’s Manual Supplement / Scheduled
Maintenance”.
ENGINE EXHAUST CAUTION
CAUTION
Avoid inhaling the engine exhaust. It contains
carbon monoxide, which is a colorless and odorless
gas. It can cause unconsciousness or even death.
 Make sure the exhaust system has no holes or loose
connections. The system should be checked from
time to time. If you hit something, or notice a change
in the sound of the exhaust, have the system checked
immediately.
 Do not run the engine in a garage or enclosed area
except for the time needed to drive the vehicle in or
out. The exhaust gases cannot escape, making this
a particularly dangerous situation.
 Do not remain for a long time in a parked vehicle with
the engine running. If it is unavoidable, however, do
so only in an unconfined area and adjust the heating
or cooling system to force outside air into the vehicle.
Keep the back door closed while driving. An open or
unsealed back door may cause exhaust gases to be
drawn into the vehicle.
 To allow proper operation of your vehicle’s
ventilation system, keep the inlet grilles in front of the
windshield clear of snow, leaves, or other
obstructions.
 If you smell exhaust fumes in the vehicle, open the
windows and close the back door to ensure plenty of
fresh air enters the vehicle. If you can smell exhaust
fumes even though there are no other vehicles in the
surrounding area, have your vehicle checked by your
Lexus dealer. Continued inhalation of exhaust fumes
can lead to death by gas poisoning.

STARTING AND DRIVING
264
(c) Using the “3”, “2” and “L” positions
The “3”, “2” and “L” positions are used for strong engine
braking as described previously.
With the selector lever in “3”, “2” or “L”, you can start the vehicle
in motion as with the lever in “D”.
With the selector lever in “3” or “2”, the vehicle will start in firs\
t
gear and automatically shift to second gear.
With the selector lever in “L”, the transmission is engaged in
first gear.
NOTICE
 Be careful not to overrev the engine. Watch the
tachometer to keep engine rpm from going into the
red zone. The approximate maximum allowable
speed for each position is given below for your
reference:
Transmission Transfer
“L” “H”
“4” 72 km/h (45 mph) 178 km/h (111 mph)
“3” 52 km/h (32 mph) 127 km/h (79 mph)
“2” 36 km/h (22 mph) 87 km/h (54 mph)
“L” 20 km/h (12 mph) 51 km/h (32 mph)
 Do not continue hill climbing or hard towing for a long
time in the “3”, “2” or “L” position. This may cause
severe automatic transmission damage from
overheating. To prevent such damage, “4” position
should be used in hill climbing or hard towing.
(d) Backing up
31X010e
 1
Brake pedal 2“R” (Reverse) position
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the
selector lever to the “R” position.
NOTICE
Never shift into reverse while the vehicle is moving.
When you are backing up, you can adjust the outside rear view
mirror on the passenger’s side down quickly. For details, see
page 195.