Page 394 of 601
STARTING AND DRIVING
373
Slip indicator light
Leave the system on during the ordinary driving so that it
can operate when needed.
You may hear a sound in the engine compartment for a few
seconds when the engine is started or just after the vehicle
begins to move. This means that the active traction control
system is in the self−check mode, but does not indicate a
malfunction.
When the active traction control system is operating, the
following conditions occur:
The system controls the spinning of the 4 wheels. At this
time, the slip indicator light blinks.
You may feel vibration or noise in your vehicle, caused by
operation of the brakes. This indicates the system is
functioning properly. The slip indicator light comes on for a few seconds when the
ignition key is turned to “ON”. If the indicator light does not
come on when the ignition is turned on, contact your Lexus
dealer.
The brake actuator temperature increase during continuous
operation of the following systems.
Active traction control system
Vehicle stability control system
Downhill assist control system
Hill −start assist control
If the brake actuator temperature becomes too high while any
of the systems is operating, a buzzer will start to sound
intermittently to indicate that the active traction control system
can no longer operate. In this case, immediately stop your
vehicle at a safe place.
If the system continues to operate, the buzzer sound changes
from intermittent to continuous. (The continuous buzzer
sounds for about 3 seconds.) At the time, the slip indicator light
will come on and the active traction control system temporarily
stops operating in order to protect the brake actuator.
(Although the active traction control system does not operate,
there is no problem to continue your driving.) The system will
be automatically restored after a short time and the slip
indicator light goes out.
Page 400 of 601
STARTING AND DRIVING
379
If you push the “DAC” switch to turn the system off while it is
in operation, the system will stop operating gradually. The
downhill assist control system indicator light will flash to alert
the driver. To continue driving at a low speed, push the “DAC”
switch to turn the system on.
The slip indicator light and downhill assist control system
indicator
light come on for a few seconds when the ignition key
is turned to “ON”. If any of the indicator lights does not come
on when the ignition is turned on, contact your Lexus dealer.
The brake actuator temperature increases during continuous
operation of the following systems.
Active traction control system
Vehicle stability control system
Downhill assist control system
Hill −start assist control
If the brake actuator temperature becomes too high while any
of the systems is operating, a buzzer will start to sound
intermittently to indicate that the downhill assist control system
can no longer operate. In this case, stop your vehicle
immediately at a safe place.
If the system continues to operate, the buzzer sound changes
from intermittent to continuous. (The continuous buzzer
sounds for about 3 seconds.) At this time, the slip indicator light
will come on and the downhill assist control system stops
operating temporarily in order to protect the brake actuator.
(Although the downhill assist control system does not operate,
it is no problem to continue your driving.) The system will be
automatically restored after a short time and the slip indicator
light goes out.
“VSC TRAC” warning light
If there is any abnormality in the system, the “VSC TRAC”
warning light will come on. When the “DAC” switch is
pushed, the downhill assist control system indicator light
also flash.
Page 403 of 601
STARTING AND DRIVING
382If the system continues to operate, the buzzer sound changes
from intermittent to continuous. (The continuous buzzer
sounds
for about 3 seconds.) At this time, the slip indicator light
will come on and the hill −start assist control stops operating
temporarily in order to protect the brake actuator. (Although
the hill−start assist control does not operate, it is no problem
to continue your driving.) The system will be automatically
restored after a short time and the slip indicator light goes out.
“VSC TRAC” warning light
If there is any abnormality in the system, the “VSC TRAC”
warning light will come on.
If the system malfunctions, the “VSC TRAC” warning light will
come on.
If the “VSC TRAC” warning light comes on, there may be an
abnormality in any of the following systems in addition to the
hill−start assist control.
Downhill assist control system
Active traction control system
Vehicle stability control system
When the system is normal and the ignition key is turned to
“ON”, the warning light will come on and will go off after a few
seconds. It is not a malfunction that the warning light may stay
on for 60 seconds after the ignition key is turned to the “ON”
position.
Page 415 of 601
STARTING AND DRIVING
3942 sets of ID codes can be registered. The code of the tires
originally
installed on the vehicle is registered on the switch at
“MAIN”. Have a new tires set with new air pressure sensors
registered at “2nd” by Lexus dealer.
ID codes should be registered by Lexus dealer. Once
registered, change the setting position each time you purchase
tires and wheels. Re −registration is not required.
When purchasing new tires, consult your Lexus dealer.
CAUTION
When the tires whose ID code is registered at “MAIN”
are used, the system does not work properly with the
selector switch set at “2nd”. If the tires whose ID code
is registered at “2nd” are stored nearby, the system will
detect their tire pressure (and vice versa).
BRAKE PAD WEAR LIMIT INDICATORS
The brake pad wear limit indicators on your disc brakes
give a warning noise when the brake pads are worn to the
extent that replacement is required.
If you hear a squealing or scraping noise while driving, have the
brake pads checked and replaced by your Lexus dealer as
soon as possible. Expensive rotor damage can result if the
pads are not replaced when needed.
Page 483 of 601
IN CASE OF AN EMERGENCY
462
Advisor record
1
PTT (Push To Talk) button 2
Volume button
3
Phone button 4
“SERVICES” button
During a service call, you can record a conversation with the
Lexus Link Call Center Advisor. This function is very
convenient for drivers so they do not have to take notes while
driving.
To record: Push “SERVICES” button to record a conversation
with Lexus Link Call Center. At this time, you will hear beeps.
To stop recording, push the button again. Up to about 2
minutes of recording time is available.
When you push the “SERVICES” button, all previous
messages are deleted and the system begins recording your
new message. To playback:
Push the PTT or phone button and “Lexus Link
ready” will be announced. Then say “Advisor playback” to play
the recorded conversation. To stop the playback, push the
phone button. To restart the playback, say “Advisor playback”
and then “Resume” for resuming or “Play” for starting from t\
he
beginning.
To change the volume: Push “− VOL +” button on either side
to adjust the volume. When you change the volume, one beep
sounds.
Page 485 of 601
IN CASE OF AN EMERGENCY
464
Voice Recognition
You can start voice recognition by pressing the phone or
PTT button. Although either button works the same way,
use the PTT button during a call.
Pressing the phone button during a call will terminate the call.
Some English audible voice prompts can be changed to
Spanish. For details, see “Audible voice prompts” on page
478.
ADVISOR PLAYBACK
Your Lexus Link system is equipped with an advisor playback
recorder to store information given to you during a call with a
Lexus Link Advisor. You can play back the stored audio
information at a later time, when you are no longer connected
to Lexus Link.
To record a conversation only during a call with Lexus
Link Call Center:
1. Press the “SERVICES” button.
You will hear beeps and recording starts. Note that start of
recording may be delayed up to five seconds to clear existing
audio information. Recording starts immediately after the last
beep.
2. Press the “SERVICES” button again.
Recording ends. To play back (only when the Lexus Link System is not in
a call):
1. Press the phone button.
You will hear “Lexus Link ready”.
2. Say “Advisor playback” .
The playback will start.
To stop the playback (partially through):
1. Press the phone* button.
The system will terminate the playback and return to audio
system control.
*: The PTT button cannot be used instead of the phone button.
To resume the playback:
1. Press the phone button.
You will hear “Lexus Link ready”.
2. Say “Advisor playback” .
You will hear “Play or resume?”.
3. Say “Play” or “Resume”.
If you say “Play”, the playback will start from the beginning. If\
you say “Resume”, the playback will start from where it had
been previously stopped.