2006 Lexus GS430 brake

STARTING AND DRIVING
400
2Cancelling the preset speed
You can cancel the preset speed by doing any of the following:
a. Pulling the control lever in the ”CANCEL” direction.
b. Depressing the brake pedal.
c. Pushing the “ON− OFF” button.
If the vehicle speed falls below about 40 km/h (25 mph), the
preset speed will be automatically cancelled.
If the vehicle speed drops 16 km/h (10 mph) below the preset
speed, the preset speed will also automatically be cancelled.
If the slip indicator light blinks and a warning tone sounds, the
preset speed will be automatically cancelled.
If the preset speed automatically cancels out for other than the
above reasons, do not operate the cruise control. Although it
is no problem to continue driving, have your vehicle checked
by your Lexus dealer at the earliest opportunity.
3 Resetting to a faster speed
Press the control lever upward in the “+ RES” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held upward, the vehicle will gradually gain
speed.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
increased 1. 6 km/h (1 mph) each time by pressing the control
lever upward in the “+ RES” direction quickly within 0.6
seconds. However, a quicker way to reset is to accelerate the vehicle
and then press the control lever downward in the “– SET”
direction.
4
Resetting to a slower speed
Press the co ntrol lever downward in the “– SET” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will
gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the “– SET” direction quickly within 0.6
seconds.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the “– SET”
direction.
With the cruise control on, even if you downshift the
transmission from the “D” position or “6” (sixth range) to the “5”\
(fifth range), or from the “D” position or “5” (fifth ran\
ge) to the
“4” (fourth range), engine braking will not be enabled because
the cruise control is not cancelled. To decrease the vehicle
speed, reset to a slower speed with the cruise control lever or
depress the brake pedal. If you use the brake pedal, cruise
control is cancelled.

STARTING AND DRIVING
401
5Resuming the preset speed
If the preset speed is cancelled by pulling the control lever, by
depressing the brake pedal or vehicle stability control
activation, pushing the lever up in the “+ RES” direction will
restore the speed set prior to cancellation. However, once the
vehicle speed falls below about 40 km/h (25 mph), the preset
speed will not be resumed.
Cruise control failure warning
If the “CRUISE” indicator light in the instrument cluster flashes
when using the cruise control, push the “ON −OFF” button to
turn the system off and then push it again to turn it on.
If any of the following conditions then occurs, there is some
trouble in the cruise control system.
 The indicator light does not come on.
 The indicator light flashes again.
 The indicator light goes out after it comes on.
If this is the case, contact your Lexus dealer and have your
Lexus inspected.
DYNAMIC RADAR CRUISE CONTROL
The vehicles with precollision system are equipped with
dynamic radar cruise control.
Dynamic radar cruise control allows you to drive at a
selected cruising speed over about 45 km/h (28 mph) with
your foot off the accelerator pedal, maintaining an
appropriate vehicletovehicle distance.
CAUTION
Do not rely excessively on dynamic radar cruise control
in order to avoid serious injury or death, or to prevent
accidents or to control the vehicle’s speed in
emergency situations. Do not use cruise control except
in appropriate road and traffic conditions. Always drive
carefully and attentively. Before using dynamic radar
cruise control, read and understand the following
instructions.

STARTING AND DRIVING
404If no vehicle is running ahead of you:
1
Cruising at a fixed speed: If there is no vehicle detected
ahead, your cruising speed is maintained at the preset
speed from about 45 km/h (28 mph) to about 135 km/h (85
mph). The preset speed is displayed in the
multi−information display. For the vehicle speed setting,
see “Setting operation ” on page 408.
If a vehicle is detected ahead of you:
2 Deceleration cruising function: If a slower moving
vehicle is detected ahead of you, your vehicle cruising
speed decreases within the range of about 40 km/h (25
mph) to about 135 km/h (85 mph). The multi− information
display shows the preset speed, the detected vehicle
ahead and selected vehicle− to−vehicle distance. If your
vehicle gets closer to the vehicle ahead because of
insufficient automatic deceleration, then the warning tone
warns you to also manually apply brakes.
3 Followup cruising function: After deceleration, your
vehicle cruising speed changes in proportion to the speed
of the vehicle ahead to maintain an appropriate distance
from your vehicle to the vehicle ahead. The
vehicle −to−vehicle distance can be changed. For details,
see “Changing vehicle −to−vehicle distance setting” on
page 412.
4 Acceleration cruising function: If the vehicle ahead
changes lanes, your vehicle cruising speed will be
gradually increased up to the preset speed, and your
vehicle resumes fixed− speed cruising.
CAUTION
Under certain conditions where the vehicle in front
slows drastically, or is stopped, the dynamic radar
cruise control will neither warn you nor decelerate. The
driver must depress the brake pedal to slow down,
ensuring collision avoidance or that sufficient
vehicletovehicle distance is maintained.
When vehicle−to−vehicle distance control mode is activated,
you must still be attentive to road and traf fic conditions. Should
your vehicle speed decrease below about 40 km/h (25 mph),
the dynamic radar cruise control will shut off, requiring you to
apply the brakes to slow. When a vehicle ahead slows
suddenly, stops or a vehicle cuts in front, the system may slow
your vehicle abruptly, but the automatic braking will cease if the
speed decreases below about 40 km/h (25 mph) requiring the
driver’s manual application of brakes.

STARTING AND DRIVING
409
After bringing the vehicle to
the desired speed, press the
control lever downward in the “– SET” direction and release it.
This sets the vehicle at that speed. At this time, the
multi−information display indicates settings such as the preset
vehicle speed, whether a vehicle is present ahead and
selected vehicle −to−vehicle distance. If there is no vehicle
detected ahead, the dynamic radar cruise control screen does
not display the vehicle ahead. At this time, you may take your
foot off the accelerator pedal. If you need to accelerate − for
example, when passing − depress the accelerator pedal
enough for the vehicle to exceed the preset speed. When you
release the accelerator pedal, the vehicle will return to the
control prior to acceleration.
You cannot set a desired speed if the master warning light
comes on, the warning tone sounds and the multi− information
display indicates a warning message such as “CRUISE NOT
AVAILABLE”, “CLEAN RADAR SENSOR” or “CHECK
CRUISE SYSTEM”. If any of the above messages appears on
the display, see “Vehicle −to−vehicle distance control mode
failure warning” on page 417.
If you turn off the “ON−OFF” button while the warning message
is displayed, the warning message turns off and the
multi−information display switches to another screen. If no
warning message appears on the display, when you turn the
“ON−OFF” button on again, the setting can be made.
You can change the dynamic radar cruise control screen to
another screen even while the warning message is displayed.
2 Cancelling the preset speed
You can cancel the preset speed by doing any of the following:
a. Pulling the control lever, in the ”CANCEL” direction.
b. Depressing the brake pedal.
c. Pushing the “ON− OFF” button.
If cancelled by a. or b., the multi−information display shows
“RADAR READY” and the dynamic radar cruise control enters
the ready mode.
If cancelled by c., the “CRUISE” indicator light goes off in the
instrument cluster and the multi −information display shows
“CRUISE OFF”. In this case, the preset speed data is cleared,
and you must set the speed from the beginning.
In the following case, the preset speed automatically
cancels out. At this time, the multiinformation display
shows “RADAR READY” and the dynamic radar cruise
control enters the ready mode.
The vehicle speed falls below about 40 km/h (25 mph). (40
km/h (25 mph) is designated as a cancel speed.)
CAUTION
In this case, the warning tone reminds you that the
dynamic radar cruise control is cancelled and you must
apply the brakes to slow the vehicle.

STARTING AND DRIVING
410In the following cases, the warning messages appear and
the preset speed automatically cancels out. When
dynamic radar cruise control is restored, the warning
messages turn off and dynamic radar cruise control
enters “RADAR READY” mode.
a. The slip indicator light blinks and a warning tone sounds.
(This occurs when the vehicle is about to skid.)
b. The driving pattern selector switch is set to snow mode.
c. The anti
−lock brake system is activated by automatic
braking. (The warning tone sounds.)
d. The sensor does not operate properly because a foreign
matter sticks to the sensor.
e. The wipers are operated at high speed (including high
speed operation with the wiper lever in the “AUTO” position.)
NOTICE
If the preset speed automatically cancels out for other
than the above reasons, do not operate the dynamic
radar cruise control. Although it is no problem to
continue driving, have your vehicle checked by your
Lexus dealer at the earliest opportunity.
3 Resetting to a faster speed
Press the control lever upward in the ”+ RES” direction and
hold it. The displayed speed will increase in increments of 5
mph (for the U.S.A.) or 5 km/h (for Canada). Release the lever
when the desired speed is attained. The vehicle will gradually
increase to the displayed speed.
Depressing the accelerator pedal and pressing the control
lever downward in the “– SET” direction will not reset to a faster
speed. At this time the set speed falls by 5 mph (for the U.S.A.)
or 5 km/h (for Canada).
CAUTION
When the vehicletovehicle distance control is on (on
followup cruising), your cruising speed is regulated in
proportion to the speed of the vehicle ahead, so
increasing the preset vehicle speed using the control
lever does not accelerate the vehicle. However, if the
vehicle ahead leaves the lane, your cruising speed will
increase up to the preset speed because the preset
speed has been set higher using the control lever.
Confirm the setting on the multiinformation display.

STARTING AND DRIVING
411
4Resetting to a slower speed
Press the c ontrol lever downward in the “– SET” direction and
hold it. The displayed speed will decrease in increments of 5
mph (for the U.S.A.) or 5 km/h (for Canada). Release the lever
when the desired speed is attained. The vehicle will gradually
decrease to the displayed speed.
A quicker way to reset the preset speed is to depress the brake
pedal and then press the control lever downward in the “– SET”
direction.
If the control lever is released when the vehicle speed exceeds
the upper limit of the preset speed traveling downhill while you
are pressing the control lever downward, the system will
memorize the upper limit of the preset speed as a preset
speed.
Even if you downshift the transmission from “D” or “6” (six\
th
range) to “5” (fifth range), or from “D” or “5” (f\
ifth range) to “4”
(fourth range) in the vehicle −to− vehicle distance control mode,
engine braking will not be enabled because this mode is not
cancelled. To decrease the vehicle speed, reset to a slower
speed with the cruise control lever or depress the brake pedal.
If you use the brake pedal, cruise control is cancelled. 5 Resuming the preset speed
If the preset speed has been cancelled, when you push the
lever up in the “+ RES” direction while “RADAR READY”
shows up on the multi −information display and at a vehicle
speed of about more than 40 km/h (25 mph), the speed set
prior to cancellation will be restored.
During follow −up cruising, if there are no vehicles running
ahead because they have changed lanes, your vehicle will
accelerate gradually up to the preset speed.

STARTING AND DRIVING
412
CAUTION
Deceleration cruising function and approach
warning do not operate when the vehicle ahead is at
a stop or driving very slowly.
 While vehicletovehicle distance control is on (on
followup cruising), acceleration and deceleration
are automatically performed in proportion to the
speed of the vehicle ahead detected. However, if the
vehicle ahead of you decelerates abruptly or if
another vehicle cuts in ahead of you, your vehicle
may collide with the vehicle ahead unless you
manually depress the brake pedal to slow down your
vehicle. If you need to accelerate because the vehicle
ahead or you changes lanes, then depress the
acceleration pedal.
 Depending on the road configuration (curved roads,
left and right continuous curved roads, driving at the
start or end of the curve, narrow driving lanes due to
road construction) or your vehicle condition
(steering wheel maneuvering, position in the lane or
unstable driving because of an accident or
breakdown), vehicles in other lanes or surrounding
objects will be detected, resulting in a control failure
or the activated approach warning. This may also
result in a very close distance between vehicles due
to a failure to detect the vehicle ahead. Maneuvering
the steering wheel in response to a violent lateral
wind will cause similar conditions.
(d) Changing vehicletovehicle distance
G31016
 1 Long 2Middle 3Short
You can select one of the following vehicletovehicle
distances: “Long”, “Middle” or “Short”. Each time you
pull the distance switch briefly toward you, the setting
changes from “Long” to “Middle” to “Short” and then
back to “Long”. You can confirm the setting on the
multiinformation display.
It should be noted that pushing the “DISP” switch will change
to another screen.
Your vehicle speed changes in proportion to the speed of
the vehicle ahead, maintaining the selected distance.
However, if the vehicle speed is slower, the selected
distance will be shorter than the designated distance.
When the vehicle− to−vehicle distance control mode is
activated or the multi−information display indicates “RADAR
READY”, the vehicle −to −vehicle distance setting can be
changed.

STARTING AND DRIVING
413
The vehicle−
to−vehicle distance is always set to “Long” when
the engine switch is turned on.
CAUTION
 Select the vehicletovehicle distance
considering traffic conditions. The approximate
vehicletovehicle distance based on time
interval when driving at 80 km/h (50 mph) is
shown below :
“Long” about 50 m (about 164 ft.) . . . . . . . .
“Middle” about 40 m (about 132 ft.) . . . . . .
“Short” about 30 m (about 100 ft.) . . . . . . .
If the vehicle speed is slower than 80 km/h (50 mph),
the distance will be shorter than the above.
 During long downhill driving, the vehicletovehicle
distance will be shorter than the selected distance.
(e) Braking control
Dynamic radar cruise control is not a collision avoidance
system. If an approach warning is activated, depress the brake
pedal to decelerate to ensure an appropriate
vehicle −to−vehicle distance.
G31017
 1
Under the vehicletovehicle distance control
2Braking activated
Braking control is operating only when the vehicle −to− vehicle
distance control mode is selected and your vehicle speed
exceeds about 40 km/h (25 mph).
If you are getting closer to the vehicle ahead at relatively higher
speed than those of the vehicle ahead or if engine braking
cannot be applied properly, braking control is automatically
activated. At this time, “BRAKE” flashes on the
multi−information display, indicating that the brakes are being
used.