2006 Lexus GS430 light

OCCUPANT RESTRAINT SYSTEMS
192
G16054
2. Fully extend the shoulder belt to put it in the lock mode.
When the belt is then retracted even slightly, it cannot be
extended.
To hold the convertible seat securely, make sure the belt is in
the lock mode before letting the belt retract.
G16055
3. While pressing the convertible seat firmly against the seat
cushion and seatback, let the shoulder belt retract as far as it
will go to hold the convertible seat securely.

OCCUPANT RESTRAINT SYSTEMS
201
1. Widen the gap
between the seat cushion and seatback
slightly and confirm the position of the lower anchorages
near the button on the seatback.
Type A—
2. Latch the hooks of lower straps onto the anchorages
and tighten the lower straps.
Type B—
2. Latch the buckles onto the anchorages
For owners in Canada—The symbol on a child restraint
system indicates the presence of a lower connector system.
If your child restraint system has a top strap, it should be
anchored. (For the installation of the top strap, see “Using a top
strap” on page 197.)
For installation details, refer to the instruction manual
equipped with each product.
CAUTION
 When using the lower anchorages for the child
restraint system, be sure that there are no irregular
objects around the anchorages or that the seat belt is
not caught.
 Push and pull the child restraint system in different
directions to be sure it is secure. Follow all the
installation instructions provided by its
manufacturer.

OCCUPANT RESTRAINT SYSTEMS
202
DRIVING POSITION MEMORYSYSTEM
A microcomputer will memorize the position of the driver’s
seat, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Three different driving position
profiles can be entered into the computer’s memory.
Recording a driving position in the computer’s memory can
only be done when the engine switch is selected in “IG −ON”
mode and the selector lever is in the ”P” position.
Setting the driving position
G16068
1. Adjust the driver’s seat, tilt and telescopic steering and
outside rear view mirrors to the desired position.
2. While pushing the ”SET” button, push button ”1”,”2” or
“3” until the signal beeps. The beep sound means that the positions are recorded in the
computer’s memory.
By repeating these two steps
and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.
Recalling the memorized position
G16069
When you push button ”1”, ”2” or “3”, the driving position
will be automatically adjusted to the position recorded for
that button.

OCCUPANT RESTRAINT SYSTEMS
204
FRONT PASSENGER SEAT
POSITION MEMORY SYSTEM
A microcomputer can memorize the position of the front
passenger seat. Three different seat position profiles can be
entered into the computer’s memory.
Recording a seat position in the computer’s memory can only
be done when the engine switch is selected in “IG −ON” mode
and the selector lever is in the ”P” position.
Setting the front passenger seat position
G16123
1. Adjust the front passenger seat to the desired position.
2. While pushing the ”SET” button, push button ”1”,”2” or
“3” until the signal beeps. The beep sound means that the positions are recorded in the
computer’s memory.
By repeating these two steps
and pressing the remaining
button, the seat position for another passenger can be
recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.
Recalling the memorized position
G16124
When you push button ”1”, ”2” or “3”, the seat positio\
n
will be automatically adjusted to the position recorded for
that button.

STEERING WHEEL AND MIRRORS
209
Automatic tilt away*
G17003
When the engine switch is off, the steering column moves
forward away from the driver and also tilts up for easy exit
and entry.
When you turn on the engine switch, the steering column
returns to the previously set position.
NOTE:
*This feature can be deactivated.
Ask your Lexus dealer for details.
OUTSIDE REAR VIEW MIRRORS
G17004
Adjust the mirror so that you can just see the side of your
vehicle in the mirror.
Be careful when judging the size or distance of any object seen
in the outside rear view mirror on the passenger’s side
because it is a convex mirror. Any object seen in a convex
mirror will look smaller and farther away than if seen in a normal
flat mirror.
When the inside rear view mirror darkens in ”AUTO” mode, the
outside rear view mirrors also darken to reduce the reflection
of the headlights of the following vehicle. For details, see
”Inside rear view mirror” on page 213.
When you push the rear window and outside rear view mirror
defogger switch, the heater panels in the outside rear view
mirrors will quickly clear the mirror surface. (See “Rear window
and outside rear view mirror defogger switch” on page 58.)

STEERING WHEEL AND MIRRORS
210
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the driver to mishandle the
vehicle and an accident may occur resulting in death
or serious injuries.
 Since the mirror surfaces can get hot, do not touch
them when the rear window and outside rear view
mirror defogger switch is on.
Power rear view mirror control
The power rear view mirror control switch is located in the
switch box.
G17013
 1
Master switch 2Control switch
Push the button to use the switch box. Push “L” (left
mirror) or “R” (right mirror) on the master switch and then
push the control switch on the desired side.
The indicator light of the switch you selected comes on when
you push “L” or “R”.
When you move the selector lever to “R” position with “L” or “\
R”
switch on, the rear view mirrors will be automatically adjusted
down to help backing up.
While the indicator light is on, the mirror can be adjusted.
When you push the same side again, the light goes out and the
mirror cannot be adjusted. After adjustment, be sure to close
the switch box to its original position.

STEERING WHEEL AND MIRRORS
212
CAUTION
To avoid personal injury and any mirror malfunction,
do not touch the mirror while it is moving.
 Do not drive with the mirrors folded backward. Both
the driver and passenger side rear view mirrors must
be extended and properly adjusted before driving.
 To reduce the chance of injury in case of an accident
or a sudden stop, keep the switch box closed when
not in use while driving.
Outer foot lights
G17015
The outer foot lights illuminate the ground near the doors
for about 15 seconds to ensure safe footing for the driver
and passengers who are about to get in the vehicle.*
The outer foot lights come on in the following conditions:
You are getting closer to the vehicle carrying an electronic
key and you enter the effective range of the entry function
(about 1 m (3 ft) from each outside door handle).
 The doors are unlocked with the wireless remote control.
 The doors are unlocked with the power door lock switch on
the driver’s side.

STEERING WHEEL AND MIRRORS
213
The outer foot lights go off 15 seconds after the lights come on
or when:

Pushing the lock switch on the outside door handle with an
electronic key in possession,
 the doors are locked with th e wireless remote control
function,
 the doors are locked by inserting a mechanical key into the
door keyhole,
 the doors are locked with the power door lock switch on the
driver’s side, or
 the selector lever is moved out of “P” position when the
engine switch is on.
NOTE:
* The outer foot lights illuminating time can be changed.
Ask your Lexus dealer for details.
INSIDE REAR VIEW MIRROR
G17007
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the “AUTO” button changes the mode between
”AUTO” and ”DAY”.
The indicator comes on when the ”AUTO” mode is selected.
”DAY” mode: The mirror surface is normal.
”AUTO” mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the engine switch is selected in “IG −ON” mode, the
inside rear view mirror always turns on in the ”AUTO” mode.