2006 Lexus GS430 CD player

AUDIO
306
G22078
Up to 29 letters can be displayed. “NO TITLE” is displayed
while the CD− TEXT disc is not playing. To cancel it, touch the
“TITLE OFF” switch. (h) If the player malfunctions
If the player or another unit equipped with the player
malfunctions,
our audio system will display one of the following
error messages.
If “CD CHECK” appears on the display: It indicates that the
disc is dirty, damaged or it was inserted up side down. Clean
the disc or insert it correctly.
If “CD ERROR” appears on the display: The following
causes are possible.
 There is trouble inside the system. Eject the disc.
 The inside of the player unit may be too hot due to the very
high ambient temperature. Eject the disc and allow the
player to cool down.
If the malfunction is not rectified: Take your vehicle to your
Lexus dealer.

AUDIO
307
DVD player operation (For a Mark Levinson
brand audio system)
The DVD player can play audio CDs, DVD video discs and
video CDs.
For appropriate discs for this paper, see “Audio system
operating hints” on page 333.
For safety reasons, you can enjoy DVD video discs and video
CDs only when the vehicle is completely stopped with the
engine switch in “ACC” or “IG−ON” mode and the parking
brake applied. While you are driving, you can hear audio alone
even in the DVD video or video CD mode.
The DVD player can play the discs labeled as shown below. (a) Inserting or ejecting discs
The engine switch must be in “ACC” or “IG
−ON” mode.
Your automatic changer can store up to 6 discs.
G22048
 Setting a single disc:
1. Push the “LOAD” button briefly.
The green indicators at both ends of the slot start blinking and
“WAIT” appears on the display. After the blinking indicators
stay on and the “WAIT” changes to the “LOAD”, the DVD door
opens.

AUDIO
3082. Insert only one disc while the DVD door is open.
You can set a disc at the lowest empty disc number.
After insertion, the set disc is automatically loaded.
If the label faces downward, the disc cannot be played. In this
case, “DISC CHECK” appears on the display.
If you need to insert the next disc, repeat the same procedure
to insert another disc.

Setting all the discs:
1. Push the “LOAD” button until you hear a beep.
The green indicators at both ends of the slot start blinking and
“WAIT” appears on the display. After the blinking indicators
stay on and the “WAIT” changes to the “LOAD”, the DVD door
opens.
2. Insert only one disc while the DVD door is open.
The DVD door closes and “WAIT” appears again.
3. Insert the next disc after the “WAIT” changes to the
“LOAD” and the DVD door opens.
4. Repeat this procedure until you insert all the discs.
To cancel the operation, push the “LOAD” or “DISC” button.
If you do not insert the discs within 15 seconds after pushing
the “LOAD” button and “LOAD” is displayed, the operation will
be canceled automatically.
NOTICE
Do not insert one disc stacked on top of another one or
feed them in continuously, to prevent discs from getting
stuck in the player.

AUDIO
310(b) Playing a disc
G22050
Push the “DISC” button if discs are already loaded in the
player.
The “DVD CHANGER” screen appears on the display.
The discs set in the player are played continuously, starting
with the last disc you inserted. The disc number of the disc
currently
being played, the track number and the time from the
beginning of the program are shown on the display.
When play of one disc ends, the first track of the following disc
starts. When play of the final disc ends, play of the first disc
starts again.
The player will skip any empty disc trays. (c) Selecting a desired disc
G22114
On the screen: Touch the desired disc number.
The selected disc number is highlighted in green.
The player will start playing the selected disc from the first
track.
On the audio panel: Push the
“CH DISC
” o r “ ” button.
When you release the button, the player will start playing the
selected disc from the first track.

AUDIO
311
(d) Operating an audio CD
Playing an audio CD—
G22062
Push the
“AUDIO” button to display this screen. You can
operate the switches and choose the number of the disc
you want to play. The selected disc is automatically
played. Selecting a desired track—
G22112
“SEEK TRACK” button:
Use for direct access to a desired
track.
Push the “SEEK TRACK
” or “ ” button and hold it until the
desired track number appears on the display. As you release
the button, the player will start playing the selected track from
the beginning.
Fast forward: Touch the “
” switch and hold it to fast forward
the disc. When you release the switch, the player will resume
playing from that position.
Reverse: Touch the “
” switch and hold it to reverse the disc.
When you release the switch, the player will resume playing.

AUDIO
312Searching for a desired track or a disc—
G22061
Touch the “SCAN” switch.
The bar on the upper side will be highlighted in yellow. The
player
will play the next track for 10 seconds, then scan again.
To select a track, touch the “SCAN” switch a second time. If
the player reaches the end of the disc, it will continue scanning
at track 1.
After all the tracks are scanned in one pass, normal play
resumes.
Touch the “DISK SCAN” switch.
The bar on the upper side will be highlighted in yellow. The
program at the beginning of each disc will be played for 10
seconds. To continue listening to the program of your choice,
touch the “DISC SCAN” switch a second time.
After all the audio disc are scanned in one pass, normal play
resumes. Other functions—
G22111
“RPT”
switch: Use it for automatic repeat of the track you are
currently listening to.
Touch the switch while the track is playing. When the track is
finished, the player will automatically go back to the beginning
of the track and play the track again. To cancel it, touch the
switch once again.
“DISC RPT” switch: Use it for automatic repeat of the disc
you are currently listening to.
Touch the switch while the disc is playing. When the disc is
finished, the player will automatically go back to the beginning
of the disc and play the disc again. To cancel it, touch the
switch once again.
“RAND” switch: Use it for automatic and random selection
of the disc which you are currently listening to.

AUDIO
314(e) Operating a DVD video disc
NOTE: The playback condition of some DVD video discs
may be determined by a DVD video software producer.
This DVD player plays a disc as the software producer
intended. So some functions may not work properly. Be
sure to
read the instruction manual for the DVD video disc
separately provided. For the detailed information about
DVD video discs, see “(h) DVD player and DVD video disc
information”
Precautions on DVD video disc
When recording with a DVD video or video CD, audio tracks
may not record in some cases while the menu is displayed. As
audio will not play in this case, verify that the video tracks are
playing and then activate playback.
When playback of a disc is completed:
If an audio CD is playing, the next CD will be selected and
playback will begin automatically.
If a DVD video or video CD is playing, playback will stop or
the menu screen will be displayed. The next disc will not
play back automatically. (Audio tracks cannot be heard
while the disc is stopped)
The title/chapter number and playback time display may not
appear while playing back certain DVD video discs.
CAUTION
Conversational speech on some DVDs is recorded at a
low volume to emphasize the impact of sound effects.
If you adjust the volume assuming that the
conversations represent the maximum volume level
that the DVD will play, you may be startled by louder
sound effects or when you change to a different audio
source. The louder sounds may have a significant
impact on the human body or pose a driving hazard.
Keep this in mind when you adjust the volume.

AUDIO
318Selecting a menu item—
G22035
Enter
the menu item using “ \f”, “ ”, “
” or “ ” switches
and touch “Enter”. The p layer starts playing video for that
menu item. (For details, see the manual that comes with
the DVD video disc provided separately.)
Each time you touch“Move Buttons” switch, the switches
on the screen move upward and downward.
When you touch “OFF” switch, the displayed switches are not
displayed. To display them again, touch “ON” switch.
Touch “Back”, and the previous screen returns. Searching by title—
G22036
Enter the title number using “–”, “+” and “+10” swi\
tches
and touch “Enter”. The player starts playing video for that
title number.
When you push “SEEK TRACK
” or “ ” button, you can
select a chapter.
Touch “Back”, and the previous screen returns.