2006 Lexus GS430 reset

GAUGES, METERS AND SERVICE REMINDER INDICATORS
94In the above conditions, press the control lever upward in the
“+ RES” direction and release it. The dynamic radar cruise
control will be restored, however, even after the weather
clears, if the setting operation cannot be performed or if the
warning message still appears, the system might have
malfunctioned. Although it is no problem to continue driving,
contact your Lexus dealer.
G13075
If the system malfunction is detected when dynamic radar
cruise control is in the “RADAR READY” mode or
operating, the master warning light comes on and the
“CRUISE” indicator light flashes. At this time a warning
tone sounds and the above message appears.
If this message appears, stop your vehicle in
a safe place, turn
the engine switch off, and then restart it to reset the system.
If the setting still cannot be made or the same message
appears again, the system might have malfunctioned.
Although it is no problem to continue driving, contact your
Lexus dealer.
NOTICE
While you are cruising with the dynamic radar cruise
control on, if the master warning light comes on, the
“CRUISE” indicator light flashes, “CHECK CRUISE
SYSTEM” appears on the multiinformation display and
the warning tone sounds, turn the engine switch off and
then on again. If the function is cancelled again after
setting or if settings cannot be made, the dynamic radar
cruise control system may be malfunctioning.
Although it is no problem to continue driving, have your
vehicle checked by your Lexus dealer.

OCCUPANT RESTRAINT SYSTEMS
199
Conditions for memorized position activation

Engine switch in “IG−ON” mode and selector lever in ”P”
position, with the vehicle stopped.
 Engine switch in “OFF” mode and within 30 seconds of
opening driver’s door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1”, “2” or \
“3”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.
MEMORY RECALL FUNCTION
You can recall the memorized position using the entry
function or wireless remote control.
If you unlock the door using the entry function or wireless
remote control, the memorized seat position is recalled when
the driver’s door is opened. The memorized steering wheel
position will be recalled when you push the engine switch.
This function can be used after setting by the following
procedure.
Setting the driving position onto the electronic key
The driver’s door must be closed with the engine switch turned
off.
1. Push and hold the previously memorized driving position
button “1”, “2” or “3”.
2. While depressing the button above, push and hold the
“LOCK” or “UNLOCK” button on the electronic key until a beep
sounds.
If you wish to set other driv ing position, repeat the above
procedure. The previous setting will be erased and the new
position will be set.
Resetting the driving position on the electronic key
The driver’s door must be closed with the engine switch turned
off.
1. Push and hold the “SET” button.
2. Push and hold the “LOCK” or “UNLOCK” button on the
electronic key until two beeps sound.

TOUCH SCREEN
220Average Speed
The Average Speed is displayed. The average vehicle
speed is calculated and displayed based on the total
driving
distance and the total driving time after the engine
is started.
The displayed value is updated every 10 seconds.
To calculate from the beginning, touch the “Reset” switch.
Distance
The distance after engine starting is displayed.
When refueling, be sure to stop your vehicle and turn the
engine switch off.
Handsfree system
Handsfree system allows you to make or receive a call
without taking your hands off the steering wheel by
connecting your cellular phone.
This system supports the Bluetooth. Bluetooth is a wireless
data system by which you can call without your cellular phone
connecting with a cable or placing on a cradle.
If your cellular phone does not support the Bluetooth, this
system can not function.
CAUTION
While you are driving, do not use a cellular phone or
connect the Bluetooth phone.
NOTICE
Do not leave your cellular phone in the vehicle. The
temperature indoor may be high and damage the phone.

AUDIO
275
1Audio operation screen display button
The audio operation screen is shown.
2Function switch display screen
(See page 280 for details.)
3
CD slot
(See page 300 or details.)
4Mode selectors
(See page 279 for details.)
5
Frequency turning knob
(See page 285 for details.)
6
CD load button
(See page 300 for details.)
7Radio mode: Preset tuning
(See page 285 for details.)
Tape mode: Side change of cassette tape
(See page 298 for details.)
CD mode: Disc selection
(See page 303 for details.)
8
Scan button
(See page 286 for details.)
9
Cassette tape slot
(See page 296 for details.)
10Stopping and ejecting a cassette tape
(See page 296 for details.)
11Radio mode: Seek tuning
(See page 286 for details.)
Tape/CD mode: Direct access to a desired
program
(See page 299 or 304 for details.)
12Ejecting a CD
(See page 301 or details.)
13Turning the system on and adjusting the volume
(See page 279 for details.)

AUDIO
277
1Audio operation screen display button
The audio operation screen is shown.
2Touch screen
(See page 280 for details.)
3
Disc slot
(See page 300 or details.)
4Mode selectors
(See page 279 for details.)
5
Frequency turning knob
(See page 285 for details.)
6
Disc load button
(See page 300or details.)
7Radio mode: Preset tuning
(See page 285 for details.)
Tape mode: Side change of cassette tape
(See page 297 for details.)
DISC mode: Disc selection
(See page 303 for details.)
8
Scan button
(See page 286 for details.)
9
Cassette tape slot
(See page 296 for details.)
10Stopping and ejecting a cassette tape
(See page 296 for details.)
11Radio mode: Seek tuning
(See page 286 for details.)
Tape/DISC
mode: Direct access to a desired
program
(See page 299 or 304 for details.)
12Ejecting a disc
(See page 301 or details.)
13Turning the system on and adjusting the volume
(See page 279 for details.)

AUDIO
285
G22010
Turn this knob to step up or down the frequency.
Your radio automatically changes to stereo reception when a
stereo broadcast is received. “ST” appears on the display. If
the signal becomes weak, the radio reduces the amount of
channel separation to prevent the weak signal from creating
noise. If the signal becomes extremely weak, the radio
switches from stereo to mono reception. In this case, “ST”
disappears from the display.(b) Presetting a station
G22004
1. Tune in the desired station.
2. Touch one of the station selector switches (16) and
hold it until a beep is heard. This sets the station to the
switch and the frequency appears on the switch.
Each switch can store AM, FM1 and FM2. To change the
preset station to a different one, follow the same procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse.

AUDIO
286(c) Selecting a station
Your Lexus has an electronic tuning radio (ETR). Tune in the
desired station using one of the following methods.
G22073
Preset tuning:
Touch the switch (1− 6) or push the “CH DISC
” or “ ” button for the station you want. The switch (1 −6)
is highlighted in green and station frequency appears on the
display.
Manual tuning: Turn the “TUNE” knob briefly. When you turn
the knob, the radio will step up or down to another frequency.
Seek tuning: Push the “SEEK TRACK
” or “ ” button.
The radio will begin seeking up or down for a station of the
nearest frequency and will stop on reception. Each time you
push the button, the stations will be searched out one after
another.
G22021
Scan tuning:Push the “SCAN” button. “SCAN” appears on
the display. The radio will find the next station up or down the
band, stay there for a few seconds, and then scan again. To
select a station, push the “SCAN” button a second time.
Preset scan tuning: Push the “SCAN” button and hold it until
you hear a beep. “P. SCAN” appears on the display. The radio
will tune in the next preset station up or down the band, stay
there for a few seconds, and then move to the next preset
station. To select a station, push the “SCAN” button a second
time.

AUDIO
291
(d) Presetting a channel
G22015
1. Tune in the desired channel.
2. Touch one of the channel selector switches (16) and
hold it until a beep is heard. This sets the channel to the
switch and the frequency appears on the switch.
Each switch can store three SAT channels. To change the
preset channel to a different one, follow the same procedure.
The preset channel memory is
cancelled when the power
source is interrupted by battery disconnection or a blown fuse. (e) Selecting a channel
Tune in the desired channel using one of the following
methods.
Preset tuning:
Touch the switch (1− 6) or push the “CH DISC
” or “ ” bu t t o n for the channel you want. The switch (1− 6)
is highlighted in green.
Manual tuning within the channel category: Turn the
“TUNE” knob. The radio will step up or down the channel.
Manual tuning within the current channel category: Push
the “SEEK TRACK
” or “ ” button. The radio will step up
or down the channel within the current channel category.
Touch the “TYPE SEEK” switch. The radio will step up the
channel within the current channel category.