2006 Lexus GS430 change time

GAUGES, METERS AND SERVICE REMINDER INDICATORS
71
LIGHT SENSITIVE OPTITRONMETER
Light sensitive optitron meter reduces unwanted glare of
the instrument cluster to provide a fine view for the driver.
The reflection of the instrument cluster is adjusted
automatically depending on the lighting condition of your
surrounding.
To make an adjustment, follow the procedure below.
The reflection control switch is located in the switch box.
G13044
Push the button to use the switch box. When you push the
“MODE” switch, the present setting appears on the
multiinformation display. To change the setting, push the “MODE” switch once and then
again within 6 seconds. Each time you push the button, the
setting changes in the following order:
1. AUTO−Norm
2. AUTO−Lo
3. AUTO−Hi
4. MANUAL−1
5. MANUAL−2
6. MANUAL−3
7. MANUAL−4
The setting display goes off automatically about 6 seconds
after the “MODE” switch is pushed. The mode shown last is
set.
After operation, be sure to close the switch box to its original
position.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, keep the switch box closed when not in
use while driving.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
82
MULTIINFORMATION DISPLAY
G13037
The multiinformation display provides various
information, including your vehicle’s driving condition,
outside temperature, and warning messages if your
vehicle is in trouble.
During ordinary driving, cruise information or graphic
information is displayed. However, if any problem occurs
in your vehicle, the display changes to a warning message
screen.
(a) Cruise information
The following information is shown with the engine switch
in “IGON” mode. Each time you push the “DISP” switch,
the displayed information is changed.
 Outside temperature
 Available driving distance
 Average fuel consumption after being refueled
 Current fuel consumption
 Blank
The displayed cruise information values indicate the general
driving condition and may not always reflect precise and actual
conditions.
 Outside temperature
g13047
The outside temperature is displayed. For details, see
“Outside temperature display” on page 106.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
93
Radar Cruise Control Warning
G13073
If the system cannot easily measure the
vehicletovehicle distance because of a dirty millimeter
wave radar sensor or grille cover while the dynamic radar
cruise control is on, the master warning light comes on
and the “CRUISE” indicator light flashes. At this time a
warning tone sounds and the above message appears.
If this message appears, clean the sensor and grille cover with
a soft cloth and try setting the preset speed again. If the dirt
is removed without cleaning, the system will automatically
enter the “RADAR READY” mode. If the system does not enter
the “RADAR READY” mode even after cleaning or the
message remains on the display, the system might be
malfunctioning. Although it is no problem to continue driving,
contact your Lexus dealer.
G13074
If the system cannot easily measure the
vehicletovehicle distance because of the following
conditions while the dynamic radar cruise control is on,
the master warning light comes on, the “CRUISE”
indicator light flashes. At this time a warning tone sounds
and the above message appears.
 The driving pattern selector switch is set to the snow
position mode.
 It is determined that it is difficult to make a measurement
because of bad weather (such as extremely hot weather)
 The wipers are operated at high speed with the wiper lever
in the “AUTO” position
In the following cases, the dynamic radar cruise control
switches to the “RADAR READY” mode:
 The driving pattern selector switch is changed to the normal
or power position.
 The wipers are stopped or are switched to low speed or
intermittent operation. (Including intermittent and stopped
wipers in the “AUTO” position)

INTERIOR EQUIPMENT
105
(a) To adjust a clock
G14056
You can adjust the clock manually with “H”, “M” and “:00”\
switches.
“H”: To set the hour
“M”: To set the minute.
“:00”: To adjust the time to the nearest hour.
For example, if the “:00” switch is pressed when the time is
between 9:30
− 9:59 or between 10:01 − 10:29, the time will
change to 10:00.
If the electrical power source has been disconnected from the
clock, the time display will automatically be set to 1:00.
After adjustment, touch “OK”. (b) To set the daylight saving time
G14057
You can set or cancel the daylight saving time.
“ON”:
To set the daylight saving time.
“OFF”: To cancel the daylight saving time.
After setting, touch “OK”.

INTERIOR EQUIPMENT
11 3
Programming a rolling code system
If your device is “Rolling Code” equipped, it is necessary
to follow steps 1 through 4 under the heading
“Programming the HomeLink
\b” before proceeding with
the steps listed below.
1. Locate the “training” button on the ceiling mounted garage
door opener motor. The exact location and color of the button
may vary by brand of garage door opener. Refer to the owner’s
guide supplied by the garage door opener manufacturer for the
location of this “training” button.
2. Press the “training” button on the ceiling mounted garage
door opener motor.
Following this step, you have 30 seconds in which to initiate
step 3 below.
3. Press and release the vehicle’s programmed HomeLink
\b
button twice. The garage door may open. If the door does
open, the programming process is complete. If the door does
not open, press and release the button a third time. This third
press and release will complete the programming process by
opening the garage door.
The ceiling mounted garage door opener motor should now
recognize the HomeLink
\b unit and be able to activate the
garage door up/down.
4. Repeat steps 1 through 3 for each remaining HomeLink
\b
button to program another rolling code system.
Programming an entrance gate /
Programming all devices in the Canadian
market
1. Decide which of the 3 HomeLink\b buttons you want to
program.
2. Place your hand −held gate/device transmitter 25 to 75 mm
(1 to 3 in.) away from the surface of the HomeLink
\b.
Keep the indicator light on the HomeLink
\b in view while
programming.
3. Press and hold the selected HomeLink
\b button.
4. Continuously press and release (cycle) the hand−held
gate/device transmitter button every two seconds until step 5
is complete.
5. When the indicator light on the HomeLink
\b changes from a
slow to a rapid flash after 20 seconds, you can release both
buttons.
6. Test the operation of the HomeLink
\b by pressing the newly
programmed button. Check to see if the gate/device operates
correctly.
7. Repeat steps 1 through 6 for each remaining HomeLink
\b
button to program another device.
Programming other devices
To program other devices such as home security systems,
home door locks or lighting, contact your authorized Lexus
dealer for assistance.

STEERING WHEEL AND MIRRORS
209
The outer foot lights go off 15 seconds after the lights come on
or when:

Pushing the lock switch on the outside door handle with an
electronic key in possession,
 the doors are locked with th e wireless remote control
function,
 the doors are locked by inserting a mechanical key into the
door keyhole,
 the doors are locked with the power door lock switch on the
driver’s side, or
 the selector lever is moved out of “P” position when the
engine switch is on.
NOTE:
* The outer foot lights illuminating time can be changed.
Ask your Lexus dealer for details.
INSIDE REAR VIEW MIRROR
G17007
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the “AUTO” button changes the mode between
”AUTO” and ”DAY”.
The indicator comes on when the ”AUTO” mode is selected.
”DAY” mode: The mirror surface is normal.
”AUTO” mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the engine switch is selected in “IG −ON” mode, the
inside rear view mirror always turns on in the ”AUTO” mode.

TOUCH SCREEN
231
To change the Passkey—
The Passkey in the system is initially fixed. You can
change the Passkey within 48 figures.
G18014
Touch the “Change” switch of Passkey to display “Enter
Bluetooth Passkey” screen.
G18016
Touch the desired key to input the Passkey.
Each time you touch “
”, an inputted number is deleted.
Touch “Enter”.

AIR CONDITIONING
261
If manual switching of air intake is desired—
G21008
Each time you push the air intake control button, the mode
changes in order from the RECIRCULATED AIR mode to
AUTOMATIC mode to OUTSIDE AIR mode, then back to the
RECIRCULATED
AIR mode. Each indicator light shows which
mode is now selected.
1 RECIRCULATED AIR mode— If quick circulation of
cooled air is desired, select this mode.
2 EXHAUST GAS AUTOMATIC mode—If the outside air
contains harmful substances like exhaust gas (i.e., when
the vehicle running just in front of your vehicle accelerates
rapidly), the system changes automatically from the
OUTSIDE AIR mode (with indicators
2
and 3 on) to
the RECIRCULATED AIR mode (with indicators 1
and 2 on).
3 OUTSIDE AIR mode—The system will take fresh outside
air into the vehicle. Turning off the air conditioning manually will cancel the
EXHAUST
GAS AUTOMATIC mode. If you select the “AUTO”
mode during fan operating, the air conditioning turns on and
the EXHAUST GAS AUTOMATIC mode will operate.
For normal use, it is best to keep the air intake control button
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.