2006 Lexus GS300 light

STARTING AND DRIVING
394However, a quicker way to reset is to accelerate the vehicle
and then press the control lever downward in the “– SET”
direction.
4
Resetting to a slower speed
Press the control lever downward in the “– SET” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will
gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the “– SET” direction quickly within 0.6
seconds.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the “– SET”
direction.
With the cruise control on, even if you downshift the
transmission from the “D” position or “6” (sixth range) to the “5”
(fifth range), or from the “D” position or “5” (fifth range) to the
“4” (fourth range), engine braking will not be enabled because
the cruise control is not cancelled. To decrease the vehicle
speed, reset to a slower speed with the cruise control lever or
depress the brake pedal. If you use the brake pedal, cruise
control is cancelled.
5
Resuming the preset speed
If the preset speed is cancelled by pulling the control lever, by
depressing the brake pedal or vehicle stability control
activation, pushing the lever up in the “+ RES” direction will
restore the speed set prior to cancellation. However, once the
vehicle speed falls below about 40 km/h (25 mph), the preset
speed will not be resumed.
Cruise control failure warning
If the “CRUISE” indicator light in the instrument cluster flashes
when using the cruise control, push the “ON−OFF” button to
turn the system off and then push it again to turn it on.
If any of the following conditions then occurs, there is some
trouble in the cruise control system.
The indicator light does not come on.
The indicator light flashes again.
The indicator light goes out after it comes on.
If this is the case, contact your Lexus dealer and have your
Lexus inspected.

STARTING AND DRIVING
395
DYNAMIC RADAR CRUISE
CONTROL
The vehicles with pre−collision system are equipped with
dynamic radar cruise control.
Dynamic radar cruise control allows you to drive at a
selected cruising speed over about 45 km/h (28 mph) with
your foot off the accelerator pedal, maintaining an
appropriate vehicle−to−vehicle distance.
CAUTION
Do not rely excessively on dynamic radar cruise control
in order to avoid serious injury or death, or to prevent
accidents or to control the vehicle’s speed in
emergency situations. Do not use cruise control except
in appropriate road and traffic conditions. Always drive
carefully and attentively. Before using dynamic radar
cruise control, read and understand the following
instructions.
G31009

1
Multi−information display
2
Master warning light
3
“CRUISE” indicator light
4
Distance switch
(for changing vehicle−to−vehicle distance)
5
Cruise control switch

STARTING AND DRIVING
396
Changing the dynamic radar cruise control
mode
G31010

1
Vehicle−to−vehicle distance control mode
2
Conventional (fixed speed) cruise control mode
The dynamic radar cruise control function has two cruise
control modes.
Vehicle−to−vehicle distance control mode for maintaining
an appropriate distance between vehicles
Conventional (fixed speed) cruise control mode for cruising
at preset speeds
You can change the mode by using the control lever.
The two cruise control modes function differently. If you use
dynamic radar cruise control, always confirm which mode is
selected.
Vehicle−to−vehicle distance control mode
The millimeter wave radar sensor in this system primarily
detects the reflected wave from the rear end of the vehicle
ahead of you to determine the presence of the vehicle
ahead as well as measuring the vehicle−to−vehicle
distance. The detection range of the sensor is about 120
m (400 ft.) ahead.
When the dynamic radar cruise control is on, the driving
pattern of the automatic transmission is fixed in the normal
mode, regardless of the position of the selector switch.
CAUTION
The dynamic radar cruise control is not a
collision−avoidance system and will not prevent
accidents. The dynamic radar cruise control is a vehicle
speed control device that is intended for use only on
freeways or roads where the traffic is light or moderate.
To avoid serious injury, you must use caution and be
attentive to road and traffic conditions while using
dynamic radar cruise control.

STARTING AND DRIVING
401 (b) Turning the system on
G31011
To operate the dynamic radar cruise control, push the
“ON−OFF” button. This turns the system on. When the
“CRUISE” indicator light in the instrument cluster comes on
and “RADAR READY” appears on the multi−information
display, you can now set your desired cruising speed and
vehicle−to−vehicle distance. Pushing the “ON−OFF” button
again will turn the system completely off and “CRUISE OFF”
will appear on the multi−information display.
When the engine switch is turned off, the system is also
automatically turned off. To use the dynamic radar cruise
control again, push the “ON−OFF” button again to turn it on.
When the engine switch is turned off, all the preset data is
cleared. When you use the dynamic radar cruise control again,
you need to reset the data.The multi−information display will return to the
vehicle−to−vehicle distance screen about 6 seconds after the
vehicle−to−vehicle distance screen has been changed to
another screen.
CAUTION
To avoid accidentally engaging the cruise control, keep
the “ON−OFF” button off when not using the dynamic
radar cruise control.

STARTING AND DRIVING
402(c) Setting operation
G31014

Each function is described below.
1
Setting the desired speed
The transmission must be in “D”, “6” (sixth range), “5” (fifth
range) or “4”(fourth range) before you set the cruise control
speed.After bringing the vehicle to the desired speed, press the
control lever downward in the “– SET” direction and release it.
This sets the vehicle at that speed. At this time, the
multi−information display indicates settings such as the preset
vehicle speed, whether a vehicle is present ahead and
selected vehicle−to−vehicle distance. If there is no vehicle
detected ahead, the dynamic radar cruise control screen does
not display the vehicle ahead. At this time, you may take your
foot off the accelerator pedal. If you need to accelerate − for
example, when passing − depress the accelerator pedal
enough for the vehicle to exceed the preset speed. When you
release the accelerator pedal, the vehicle will return to the
control prior to acceleration.
You cannot set a desired speed if the master warning light
comes on, the warning tone sounds and the multi−information
display indicates a warning message such as “CRUISE NOT
AVAILABLE”, “CLEAN RADAR SENSOR” or “CHECK
CRUISE SYSTEM”. If any of the above messages appears on
the display, see “Vehicle−to−vehicle distance control mode
failure warning” on page 410.
If you turn off the “ON−OFF” button while the warning message
is displayed, the warning message turns off and the
multi−information display switches to another screen. If no
warning message appears on the display, when you turn the
“ON−OFF” button on again, the setting can be made.
You can change the dynamic radar cruise control screen to
another screen even while the warning message is displayed.

STARTING AND DRIVING
403
2
Cancelling the preset speed
You can cancel the preset speed by doing any of the following:
a. Pulling the control lever, in the ”CANCEL” direction.
b. Depressing the brake pedal.
c. Pushing the “ON−OFF” button.
If cancelled by a. or b., the multi−information display shows
“RADAR READY” and the dynamic radar cruise control enters
the ready mode.
If cancelled by c., the “CRUISE” indicator light goes off in the
instrument cluster and the multi−information display shows
“CRUISE OFF”. In this case, the preset speed data is cleared,
and you must set the speed from the beginning.
In the following case, the preset speed automatically
cancels out. At this time, the multi−information display
shows “RADAR READY” and the dynamic radar cruise
control enters the ready mode.
The vehicle speed falls below about 40 km/h (25 mph). (40
km/h (25 mph) is designated as a cancel speed.)
CAUTION
In this case, the warning tone reminds you that the
dynamic radar cruise control is cancelled and you must
apply the brakes to slow the vehicle.
In the following cases, the warning messages appear and
the preset speed automatically cancels out. When
dynamic radar cruise control is restored, the warning
messages turn off and dynamic radar cruise control
enters “RADAR READY” mode.
a. The slip indicator light blinks and a warning tone sounds.
(This occurs when the vehicle is about to skid.)
b. The driving pattern selector switch is set to snow mode.
c. The anti−lock brake system is activated by automatic
braking. (The warning tone sounds.)
d. The sensor does not operate properly because a foreign
matter sticks to the sensor.
e. The wipers are operated at high speed (including high
speed operation with the wiper lever in the “AUTO” position.)
NOTICE
If the preset speed automatically cancels out for other
than the above reasons, do not operate the dynamic
radar cruise control. Although it is no problem to
continue driving, have your vehicle checked by your
Lexus dealer at the earliest opportunity.

STARTING AND DRIVING
410For vehicles sold in U.S.A.
FCC WARNING
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF exposure information
This device complies with the FCC RF exposure
requirements.
For vehicles sold in Canada
Operation is subject to the following two conditions;
(1) this device may not cause interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation of the device.
(h) Vehicle−to−vehicle distance control mode failure
warning
G31020
If there is trouble somewhere in the dynamic radar cruise
control while the vehicle−to−vehicle distance control mode is
on, the ”CRUISE” indicator light in the instrument cluster
flashes, the master warning light comes on and the warning
tone sounds, and one or more of the following warning
messages will appear on the multi−information display.
“CLEAN RADAR SENSOR”
“CRUISE NOT AVAILABLE”
“CHECK CRUISE SYSTEM”
If any warning message shown above appears, the preset
speed automatically cancels out.

STARTING AND DRIVING
412
G13075
If the system malfunction is detected when dynamic radar
cruise control is in the “RADAR READY” mode or
operating, the above message appears.
If this message appears, stop your vehicle in a safe place, turn
the engine switch off, and then restart it to reset the system.
If the setting still cannot be made or the same message
appears again, the system might have malfunctioned.
Although it is no problem to continue driving, contact your
Lexus dealer.
NOTICE
While you are cruising with the dynamic radar cruise
control on, if the master warning light comes on, the
“CRUISE” indicator light flashes, “CHECK CRUISE
SYSTEM” appears on the multi−information display and
the warning tone sounds, turn the engine switch off and
then on again. If the function is cancelled again after
setting or if settings cannot be made, the dynamic radar
cruise control system may be malfunctioning.
Although it is no problem to continue driving, have your
vehicle checked by your Lexus dealer.
Conventional (fixed speed) cruise control
mode
This mode allows you to cruise at a desired speed over
about 45 km/h (28 mph) with your foot off the accelerator
pedal.
Cruising speed can be maintained, although a slight speed
change may occur when driving up or down a gradient, within
the limits of engine performance. On steeper hills, the speed
will change more radically so it is better to drive without cruise
control.
When cruise control is on, the driving pattern of the automatic
transmission is fixed in the normal mode, regardless of the
position of the selector switch.