KEYLESS ENTRY SYSTEM
(IF EQUIPPED)You can also lock or unlock the door and
open the trunk from the outside with the
transmitter.
KNOWING YOUR VEHICLE
3-4
MMSA3067
• To lock the door, depress
this button. (Hazard
warning light is turned on
and turned off for about 1
second.)• If you depress the
corresponding button
once, only the driver’s
door will unlock. If you
depress the corresponding
button twice, all four doors
and rear hatch will unlock.
• To open the trunk, depress
this button.• If you depress the panic
button ( ) on the
transmitter, the horn will
sounds and hazard lamp
will flash.✻
NOTICE
• The transmitter will not work
under the following conditions :
- Ignition key is in the ignition
key hole.
- The battery of transmitter is
discharged.
• The operational distance(5m) is
exceeded.
• The transmitter may not operate
when the weather is very cold or
when there are other vehicles or
objects around the vehicle.
When the transmitter does not
work correctly, open and close
the door with the ignition key.
• If you have a problem with the
transmitter, contact an
Authorized Kia Dealer.
• Always use the transmitter to
lock/unlock the doors. When the
system is armed the alarm will
sound if you unlock the driver or
passengers door with the
ignition key. If at any time you
have the ignition key in the on
position for more than 30
seconds the system will
deactivate if previously armed.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 4
This device complies with Industry
Canada Standard RSS-210.Operation
is subject to the following two
conditions:
1. This device may not cause
interference, and
2. This device must accept any
interference, including interference
that may cause undesired operation of
the device.
LIMP HOME (OVERRIDE)
PROCEDUREWhen you turn the ignition key to the
ON position, if the IMMO indicator
remains on continuously after blinking 6
times, your transponder equipped in the
ignition key is out of order. You cannot
start the engine without the lime home
procedure. To start the engine, you have
to input your password by using the
ignition switch.
The following procedure is how to input
your password of “2345” as an example.
1. Turn the ignition key to the ON
position. The IMMO indicator ( )
will blink 6 times and remain on
indicating the beginning of the limp
home procedure.
2. Turn the ignition key to the ACC
position.
3. To enter the first digit (in this example
“2”), turn the ignition key to the ON
and ACC position twice. Perform the
same procedure for the next digits
between 3 seconds and 10 seconds
(for example, for “3”, turn the ignition
ON and ACC 3 times).4. If all of the digits have been input
successfully, you have to start the
engine within 10 seconds. If you
attempt to start the engine after 10
seconds, the engine will not start and
you will have to input your password
again.
After performing the limp home
procedure, you have to see an authorized
Kia dealer immediately to inspect and
repair your ignition key or immobilizer
system.
KNOWING YOUR VEHICLE
3-8
CAUTION
If you cannot start your engine in
spite of limp home procedure, have
your vehicle towed by an
authorized Kia dealer for
inspection and necessary repairs.
WARNING
Changes or modifications not
expressly approved by the
party responsible for
compliance could void the
user's authority to operate the
equipment.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 8
DRIVER’S DOOR POWER
WINDOW CONTROLSAll windows can be opened or closed
using the power window master control
on the driver’s door. To open a window,
press down on the corresponding power
window switch. To close a window, pull
up on the corresponding power window
switch.
DRIVER’S WINDOW
AUTOMATIC-DOWN WINDOW
SWITCHThe driver’s window has an “Automatic-
Down” feature. To activate the express-
down feature, momentarily depress the
front of the switch to the second detent
position. To cancel this feature, pull up
on the front of the switch and then
release it.DRIVER’S POWER WINDOW
SWITCHThe driver’s power window switch
provides two (2) separate window-down
functions.
• Depressing the driver’s power
window switch completely, automa-
tically lowers (Automatic-Down) the
driver’s window. To cancel this
function, pull up on the front of the
switch and release it.• Depressing the driver’s power
window switch partially (to the first
detent) provides precise control of the
window-down position.
To raise/close the driver’s window,
pull up on the power window switch.
POWER WINDOW TIMER
(IF EQUIPPED)The power windows can be operated for
approximately 30 seconds after the
ignition key is removed or turn to the
ACC or LOCK position. However, if the
front doors are opened, the power
windows cannot be operated even within
the 30 seconds after the ignition key
removal.
KNOWING YOUR VEHICLE
3-12
MMSA3004
Power window master controlPower window lock switch
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 12
POWER WINDOW LOCK
SWITCH FEATUREThe driver can disable the power window
switches on all passenger doors by
depressing the power window lock switch
located on the driver’s door to ON. When
the power window lock switch is ON, the
driver’s master control can not operate the
passenger door power windows either.
PASSENGER DOOR POWER
WINDOW CONTROLSTo open a window, press the front portion
of the switch down. To close a window,
pull the front portion of the switch up.
3-13
MMSA3006
WARNING - Power
Windows
Keep the power window lock
switch on the driver’s door in
the ON (depressed) position
except when someone is
operating a passenger door
window. Serious injury can
result from unintentional
window opera-tion, especially
to children.
Always double check to make
sure all arms, hands, and other
obstructions are safely out of
the way before closing a
window.✻
NOTICE
If you experience buffeting and
pulsation (wind shock) with either
side window open, you should open
the opposite window slightly to
reduce the condition.
WARNING - Passengers
Do not allow children to play
with the power windows. They
may seriously injure
themselves or others.
MMSA3004
Power window lock switch
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 13
3-19
HEATING THE FRONT
SEATS (IF EQUIPPED)The front seats are electrically heated
when the ignition switch is ON and the
corresponding heater switch, shown in
the illustration, is depressed. When
depressed, a thermostat regulates seat
temperature individually. To deactivate
the front seat heating system, depress the
corresponding heater switch again.
ADJUSTABLE HEADREST
(IF EQUIPPED)To raise the headrest, simply pull it up to
the desired position. To lower the
headrest, press the release lever on the
left side grommet, while pushing the
headrest down to the desired position. To
remove the headrest, raise it as far as it
can go then press the release lever while
pulling upward.The headrest may be adjusted forward to
three positions by pulling if forward. To
adjust the headrest backwards, pull it
forward and release it.(If equipped)
MMSA3079
MMSA3016
Release lever
WARNING - Headrests
To reduce the risk of head
and neck injuries, do not
operate the vehicle with the
headrest removed or
improperly posi-tioned.
Do not attempt to adjust the
headrest while driving.
Adjust the top of the headrest
so that it is even with the top
of your ears in order to
reduce the chance of injury in
the event of a collision.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 19
3-45 The air bags will completely inflate
and deflate in less than 1/10 of one
second.
The speed of inflation and deflation
protects the driver’s ability to operate the
vehicle. This is important in crashes
where a vehicle continues to move after
an impact and the driver still has some
control of the vehicle’s steering, braking,
throttle and/or transmission systems.
It is virtually impossible for you to see
the air bags inflate during an accident.
It is much more likely that you will
simply see the deflated air bags hanging
out of their storage compartments after
the collision.
In order to help provide protection in a
severe collision, the air bags must inflate
repidly. However, that speed also causes
the air bags to expand with a great deal of
force. The speed of this inflation has been
determined by the Canadian Motor
Vehicle Safety Standards (CMVSS) to
reduce the likelihood of serious or life-
threatening injuries and is thus a
mandatory part of air bag design.Thus, air bag inflation could also cause
injuries which normally can include facial
abrasions, bruises and broken bones.
However, there are even
circumstances under which contact
with the steering wheel air bag can
cause fatal injuries, especially if the
occupant is positioned excessively
close to the steering wheel.
YOU MUST ALWAYS SIT AS FAR
BACK FROM THE STEERING
WHEEL AIR BAG AS POSSIBLE,
WHILE STILL MAINTAINING A
COMFORTABLE SEATING POSITION
FOR GOOD VEHICLE CONTROL, IN
ORDER TO REDUCE THE RISK OFINJURY OR DEATH IN A COLLISION.
AS2B03033 Steering wheel air bag
WARNING - Air Bag
Injuries
Sit as far back from the
steering wheel as possible
without interfering with your
control of the vehicle.
Positioning yourself too close
to the steering wheel can
result in serious or even fatal
injuries if the air bag deploys.
Never place objects over the
air bag storage compartments
or between the air bags and
yourself. Due to the speed and
force of the air bag inflation,
such objects could hit your
body at high speed and cause
severe bodily injury and even
death.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 45
3-57
• To remove the cap, turn it coun
terclockwise.
• To install the cap, turn it clock wise
until it “clicks”.
This indicates that the cap is securely
tightened.The fuel filler neck is designed to
prevent filling the fuel tank with
anything but unleaded fuel.
Always insure that the
engine is OFF before and
during refueling. Once
refueling is complete, check
to make sure the fuel filler
cap and door are securely
closed, before starting the
engine.
Do not light any fire around a
gas station. DO NOT use
matches or a lighter and DO
NOT SMOKE or leave a lit
cigarette in your vehicle while
at a gas station especially
during refueling. Automotive
fuel is highly flammable and
can, when ignited, result in
explosion by flames.
If a fire breaks out during
refueling, leave the vicinity of
the vehicle, and immediately
contact the manager of the
gas station or contact the
police and local fire
department. Follow any
safety instructions they
provide.
✻
NOTICE
A loose fuel filler cap may cause the
OBD-II Malfunction Indicator
Light ( ) light in the instrument
panel to illuminate unnecessarily.
Always ensure that the fuel filler
cap is tight.
CHECK
✻
NOTICE
If the fuel filler cap requires
replacement, use only a genuine
Kia cap. An incorrect fuel filler cap
can result in a serious malfunction
of the fuel system or emission
control system. Correct
replacement caps are available at
Authorized Kia Dealers.
MMSA3049
Fuel filler cap
holderFuel filler neck Remove
Install
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 57
3-59
ELECTRIC REMOTE
CONTROLThis switch, located on the armrest of the
driver’s door, controls the adjustments for
both right and left outside mirrors. To
adjust the position of either mirror:
1. Move the selector switch to the right
or left to activate the adjusting
mechanism for the corresponding
mirror.
2. Adjust the mirror angle by depressing
the mirror adjustment control switch
in the desired direction.
MMSA3052
✻
NOTICE
Do not scrape ice off the mirror
face; this may damage the surface
of the glass. If ice should restrict
movement of the mirror, do not
force the mirror to adjust it.
To remove ice, use a de-icer spray,
or a sponge or soft cloth with very
warm water.
✻
NOTICE
The mirrors stop moving when
they reach the maximum adjusting
angles, but the motor continues to
operate while the switch is
depressed. Do not depress the
switch longer than necessary or the
motor may be damaged.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 59