2006 KIA Magnetis lock

2. Hold the transmitter of the device
you want to train 1 to 3 inches away
from the bottom of the mirror.
Simultaneously press the hand-held
transmitter button and the HomeLink
button you wish to train. The
indicator light will flash slowly at
first, then rapidly, indicating
successful programming.
3. If the garage door opener or other
device you wish to train is rolling-
code equipped, proceed to the
"Rolling Code Programming" section
below.
4. Repeat step 2 to program the
remaining HomeLink buttons.
Additional Programming for
Rolling Code DevicesFor any rolling-code-equipped device;
follow the steps below after completing
the "Programming" section. A second
person may make the following steps
easier.
1. Locate the "learn" or "smart" button
on the device's motor head unit. The
exact location and color of the button
varies by product brand, but is
usually referenced in the device's
owner's manual. Contact HomeLink
at 1.800.355.3515 or
www.homelink.com for help.
2. Press and release the "learn" or
"smart" button on the device's motor
head unit.3. Return to the vehicle and firmly press
and release the programmed
HomeLink button. Press and release
the same HomeLink button a second
time to complete the training process.
(Some devices may require you to
press and release a third time to
complete the training.)
4. Now your HomeLink mirror and the
rolling-code-equipped device should
be synchronized. The remaining
HomeLink buttons may now be
programmed if this has not been
done previously.
Operating HomeLinkSimply press the appropriate HomeLink
button to activate the trained product
(garage door, security system, entry door
lock, estate gate, lighting, etc.). The
original handheld transmitters may also
be used at any time.
DRIVING TIPS
5-14
MMSA5006
✻
NOTICE
You now have 30 seconds to
initiate step 3.
Flashing
Transmitter
1-3inches
MS-CNA-Eng 5 New.qxd 7/25/2005 5:21 PM Page 14

1. Turn the ignition switch and all other
switches off.
2. Pull the suspected fuse straight out.
Use the removal tool provided on the
main fuse box in the engine
compartment. Refer to the fuse panel
chart on the fuse panel cover to
identify the likely problem fuse or
electrical circuit.
3. Check the removed fuse; replace if it
is blown.
Four (4) spare fuses are provided in the
engine compartment fuse panel cover.4. Push in a new fuse of the same
rating, and make sure it fits tightly in
the clips.
If it fits loosely, consult an
Authorized Kia Dealer.
If you do not have a spare, use a fuse of
the same rating from a circuit you may
not need for operating the vehicle, such
as the radio or clock (Room) fuse.
If the headlights or other electrical
components do not work and the fuses
are OK, check the fuse box in the engine
compartment. If a fuse is blown, it must
be replaced.
1. Turn the ignition switch and all other
switches OFF.
2. Remove the fuse box cover by
turning the plastic knob located in the
cover counterclockwise until the
cover can be removed.
3. Check the fuses. If one is blown,
replace it with a new one of the same
rating.
IN CASE OF EMERGENCY
6-8
MMSA6020
MMSA6005
Fuse box
CAUTION
After checking the fuse box in the
engine compartment, please
securely install the fuse box cover.
If not, some electrical failures may
occur causing from the water.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 8

6-9
FUSE PANEL
DESCRIPTIONDRIVER’S SIDE KICK PANEL
L
P
G
MMSA6006
10ARR HTD IND
10AHAZARD
15ARR FOG
10AA/CON
10AETACS
15ADR LOCK10AT/SIG
10AA/BAG IND
10AH/LP
15ASTOP LP
15AT/LID OPEN
25AP/SEAT
(DRIVE)10AA/CON SW
15A
ACC SOCKET
15AS/HTR
15AA/BAG
10ASTART
15ASP 1
15AFRT HTD
10ATAIL (LH)
10AAUDIO
20AWIPER
10ATAIL (RH)
15AC/LIGHTER
10AEPS
10AROOM LP
SHUNT
USE THE DESIGNATED
FUSE ONLY.
25AP/SEAT
(PASS)
10AB/UP
10ACLUSTER10AD/CLOCK
15ASP 4
2MS106002A
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 9

IN CASE OF EMERGENCY
6-10
DESCRIPTION FUSE RATING PROTECTED COMPARTIMENTS
RR HTD IND10A Rear window defroster, Outside rear view mirror heater
HAZARD10A Hazard light, Turn signal lights
RR FOG15A Rear fog light
A/CON10A Air conditioning system
ETACS10A ETACS, Keyless entry system, Door lock system
DR LOCK15A Power door lock
P/SEAT (DRIVE)25A Power seat
T/LID OPEN15A Remote trunk lid
STOP LP15A Stop lights
H/LP10A Head light
A/BAG IND10A Air-bag
T/SIG10A Turn signal lights
A/CON SW10A Air conditioning system
ACC SOCKET15A Power outlet
S/HTR15A Seat heater
A/BAG15A Air-bag
B/UP10A Backup lights
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 10

6-11
CLUSTER10A Cluster
START10A Engine switch
SP115A Spare fuse
FRT HTD15A Window defroster
P/SEAT (PASS)25A Power Seat
SP415A Spare fuse
D/CLOCK10A Digtal clock
TAIL(LH)10A Position lights, License plate lights, Tail lights
AUDIO10A Audio
WIPER20A Wiper
ROOM LP10A Dome lights, Front door edge warning lights
TAIL(RH)10A Position lights, License plate lights, Tail lights
C/LIGHTER15A Cigar lighter
EPS10A -
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 11

WHEN YOUR VEHICLE IS
BEING TOWED BY ANOTHER
VEHICLE OTHER THAN A
TOW TRUCK (IN CASE OF AN
EMERGENCY) Turn the ignition switch to ACC so
the steering wheel isn’t locked.
 Place the transaxle shift lever in N
(Neutral).
 Release the parking bake.
 Vehicle equipped with automatic
transaxle should not exceed 45km/h
(28 mph) and should not be towed
more than 80km (50 miles).  Press the brake pedal with more force
than normal since you will have
reduced brake performance.
 More steering effort will be required
because the power steering system
will be disabled.
 If you are driving down a long hill,
the brakes may overheat and brake
performance will be reduced. Stop
often and let the brakes cool off.
TIPS FOR TOWING A STUCK
VEHICLEThe following methods are effective
when your vehicle is stuck in mud, sand
or similar substances that prevent the
vehicle from being driven out under its
own power.
 Remove the soil and sand, etc. from
the front and the back of the tires.
 Place a stone or wood under the tires.
IN CASE OF EMERGENCY
6-18
✻
NOTICE
To prevent internal damage to the
transaxle, never tow your vehicle
from the rear (backwards) with all
four tires in contact with the
surface.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 18

IF YOU HAVE A FLAT
TIRESTORING THE SPARE
TIRE, JACK AND TOOLSThe spare tire, tool bag, jack and jack
handle are stored in the trunk
compartment. Move the carpeting out of
the way to reach this equipment.
TO REMOVE THE JACK:Turn the jack socket counterclockwise.
TO REMOVE SPARE TIRE:Turn the tire hold-down wing bolt
counterclockwise.
Store the tire in the reverse order of
removal.
To prevent the jack, jack handle, and
tool bag from “rattling” while the
vehicle is in motion, store them properly.
6-19
MMSA6013
MMSA6014A
MMSA6012
Tool bag
spare tireJack
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 19

CHANGING TIRESJACKING INSTRUCTIONSThe jack is provided for emergency tire
changing only. Follow jacking
instructions to reduce the possibility of
personal injury.
TIRE REPLACEMENT1. Park on a level surface and set the
parking brake firmly.
2. Set the automatic transaxle in P
(Park), or shift the manual transaxle
into R (Reverse).
3. Activate the hazard warning flasher.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tire from
the vehicle.
5. Block both the front and rear of the
wheel that is diagonally opposite the
jack position.
IN CASE OF EMERGENCY
6-22
MMSA6015Flat tire
Wheel block
WARNING - Changing
Tires
Never attempt vehicle repairs
or a tire change in the traffic
lanes of a public road or
highway. Always move the
vehicle completely off the
road and onto the shoulder
before trying to change a tire.
If you cannot find a firm, level
place off the road, call a
towing service company for
assistance.
Be sure to use the correct
front or rear jacking
positions on the vehicle;
never use the bumpers or
any other part of the vehicle
for jack support.
Never allow any portion of
your body to get beneath the
vehicle while using the jack.
Do not start or run the engine
while the vehicle is
supported by the jack.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 22