2006 KIA Magnetis headlights

6-13
DESCRIPTION FUSE RATING PROTECTED COMPARTIMENTS
COND FAN20A Condenser fan
PWR WIND40A Power window
ABS 220A ABS
IGN SW-130A Ignition switch
ABS 140A ABS
IGN SW-230A Ignition switch
RAD FAN MTR30A Radiator fan motor
FUEL PUMP20A Fuel pump
HD LP LO15A Headlights (LO)
ABS10A ABS
INJECTOR10A Injector
A/C COMPR10A Air-con compressor
ATM RLY20A ATM Relay
ECU RLY30A Engine control unit relay
IG COIL20A Ignition coil
O
2SNSR15A Oxygen sensor
ECU15A Engine control unit
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 13

TOWINGIf emergency towing is necessary, we
recommend having it done by an
Authorized Kia Dealer or a competent
tow-truck service. Proper lifting and
towing procedures are necessary to
prevent damage to the vehicle. State and
local laws applicable to towing vehicles
must be followed.
IN CASE OF EMERGENCY
6-14
MMSA6007A
Wheel dolly
HORN10A Horn
HEAD LP HI15A Headlights (HI)
HEAD LP WASH20A -
DRL15A DRL
FR FOG15A Front fog lights
DIODE-1- Diode 1
SPARE30A Spare fuse
SPARE20A Spare fuse
SPARE15A Spare fuse
SPARE10A Spare fuse
DIODE-2- Diode 2
BLOWER30A Blower
PWR FUSE-230A Power fuse 2
PWR AMP20A Power amp
SUNROOF15A Sunroof
TAIL LP20A Tail lights
PWR FUSE-130A Power fuse 1
ECU10A ECU
RR HTD30A Rear window defroster
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 14

BATTERY MAINTENANCEFor best battery service:
• Keep the battery securely mounted.
• Keep the battery top clean and dry.
• Keep the terminals and connections
clean, tight, and coated with
petroleum jelly or terminal grease.
• Immediately rinse any spilled
electrolyte from the battery with a
solution of water and baking soda.
• If the vehicle is not going to be used
for an extended period of time,
disconnect the battery cables.
BATTERY RECHARGINGYour vehicle has a maintenance-free,
calcium-based battery.
• If the battery becomes discharged in
a short time (headlights or interior
lights were left on while the vehicle
was not in use), recharge it by slow
(trickle) charging for 10 hours.
• If the battery gradually discharges
because of high electric load while
the vehicle is being used, recharge it
at 20-30A for two hours.
MAINTENANCE
7-24
MMSA7034
(Continued)
Keep batteries out of the
reach of children
because batteries
contain highly corrosive
SULFURIC ACID. Do not allow
battery acid to contact your skin,
eyes, clothing or paint finish.
Wear eye protection
when charging or
working near a battery.
Always provide ventilation when
working in an enclosed space.
When lifting a plastic-cased
battery, excessive pressure
on the case may cause
battery acid to leak, resulting
in personal injury. Lift with a
battery carrier or with your
hands on opposite corners.
Never attempt to charge the
battery when the battery
cables are connected.
The electrical ignition system
works with high voltage. Never
touch these components with
the engine running or the
ignition switched on.
WARNING - Recharging
Battery
When recharging the battery,
observe the following
precautions:
The battery must be removed
from the vehicle and placed
in an area with good
ventilation.
Do not allow cigarettes,
sparks, or flame near the
battery.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 24

MAINTENANCE
7-42HEADLIGHT AIMING
ADJUSTMENTBefore performing aiming adjustment,
make sure of the following.
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground and
press the front bumper & rear
bumper down several times.
3. See that the vehicle is unloaded
(except for full levels of coolant,
engine oil and fuel, and spare tire, jack,
and tools). Have the driver sit in the
driver’s seat or use equivalent weight.4. Clean the headlight lenses and turn
on the headlight (Low beam).
5. Open the hood.
6. Draw a vertical line (through the
center of each headlight) and the
horizontal line (through the center of
each headlight) on the aiming screen.
1) Horizontal line dimension from
ground: 628 mm (24.72 in)
2) Distance between each vertical
line : 1,306 mm (49.17 in)
And then, draw a parallel line at 30
mm (1.18 in) place under the
horizontal line.
7. Adjust each cut-off line of the low
beam to the parallel line with a
Phillips screwdriver.
ADJUSTMENT AFTER
HEADLIGHT ASSEMBLY
REPLACEMENTIf the vehicle has had front body repair
and the headlight assembly has been
replaced, the headlight aiming should be
checked using the aiming screen as
shown in the illustration. Turn on the
headlight switch. (Low Beam Position)
1. Adjust headlights so that main axis of
light is parallel to center line of the
body and is aligned with point “P”
shown in the illustration.
MMSA7032
Vertical
aiming
HH W
P
MMSA7033
Horizontal line
21 mm (0.82 in)
Cut-off line
Ground line Vertical line
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 42

7-43
2. Dotted lines in the illustration show
center of headlights.
“H”;
Horizontal center line of headlights
from ground : 628 mm (24.72 in)
“W”;
Distance between each headlight
center: 1,306 mm (49.17 in)
“L”;
Distance between the headlights and
the wall that the lights are tested
against: 3,000 mm (118.11 in)
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 43

LIGHT BULBS TIRES
* Spare tire(Temporary Spare)
8-3
Light Bulb Wattage
FrontHeadlights 55
65
Turn signal/Position lights 28/8
Fog lights(if equipped) 55
Side mark lights (*if equipped) 5
RearStop and tail lights 28/8
Turn signal lights 27
Backup lights 16
High mounted stop lights 16
Side mark lights (*if equipped) 5
License plate lights 5
InteriorInterior lights 10
Luggage compartment light
5
(If equipped)LOW
HIGH
Size
TireP205/60R15 *T120/70 D15 or T125/70 R15
P205/55R16 (if equipped)
PressureInflation Pressure KPa(kg/cm
2,psi)
210(2.1, 30) 420(4.2, 60)
MS-CNA-Eng 8.QXD 7/25/2005 5:07 PM Page 3