2006 KIA Magnetis clock

6-9
FUSE PANEL
DESCRIPTIONDRIVER’S SIDE KICK PANEL
L
P
G
MMSA6006
10ARR HTD IND
10AHAZARD
15ARR FOG
10AA/CON
10AETACS
15ADR LOCK10AT/SIG
10AA/BAG IND
10AH/LP
15ASTOP LP
15AT/LID OPEN
25AP/SEAT
(DRIVE)10AA/CON SW
15A
ACC SOCKET
15AS/HTR
15AA/BAG
10ASTART
15ASP 1
15AFRT HTD
10ATAIL (LH)
10AAUDIO
20AWIPER
10ATAIL (RH)
15AC/LIGHTER
10AEPS
10AROOM LP
SHUNT
USE THE DESIGNATED
FUSE ONLY.
25AP/SEAT
(PASS)
10AB/UP
10ACLUSTER10AD/CLOCK
15ASP 4
2MS106002A
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 9

6-11
CLUSTER10A Cluster
START10A Engine switch
SP115A Spare fuse
FRT HTD15A Window defroster
P/SEAT (PASS)25A Power Seat
SP415A Spare fuse
D/CLOCK10A Digtal clock
TAIL(LH)10A Position lights, License plate lights, Tail lights
AUDIO10A Audio
WIPER20A Wiper
ROOM LP10A Dome lights, Front door edge warning lights
TAIL(RH)10A Position lights, License plate lights, Tail lights
C/LIGHTER15A Cigar lighter
EPS10A -
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 11

IF YOU HAVE A FLAT
TIRESTORING THE SPARE
TIRE, JACK AND TOOLSThe spare tire, tool bag, jack and jack
handle are stored in the trunk
compartment. Move the carpeting out of
the way to reach this equipment.
TO REMOVE THE JACK:Turn the jack socket counterclockwise.
TO REMOVE SPARE TIRE:Turn the tire hold-down wing bolt
counterclockwise.
Store the tire in the reverse order of
removal.
To prevent the jack, jack handle, and
tool bag from “rattling” while the
vehicle is in motion, store them properly.
6-19
MMSA6013
MMSA6014A
MMSA6012
Tool bag
spare tireJack
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 19

6-23 6. For models with alloy wheels,
remove the center cap.
7. Loosen the four lug nuts
counterclockwise one turn each, but
do not remove any nut until the tire
has been raised off the ground.8. Place the jack at the front or rear
jacking position closest to the tire
you are changing. Place the jack
under the side sill at the designated
location.9. Insert the jack handle into the jack and
turn it clockwise, raising the vehicle
until the tire just clears the ground,
approximately 1.2 in. (30 mm).
Before removing the lug nuts, make
sure the vehicle is stable and that there
is no chance for it to slip or move.
MMSA6016MMSA6017
WARNING - Changing a
Front Tire
When one front wheel is lifted
off the ground, neither the
automatic transaxle P (Park)
position nor the manual
transaxle R (Reverse) position
will prevent the vehicle from
moving and possibly slipping
off the jack, even if these
positions are properly engaged.
To prevent vehicle movements
while changing a tire, always set
the parking brake fully, and
always block the wheel
diagonally opposite the wheel
being changed.
WARNING - Jack
Location
To reduce the possibility of
injury, be sure to use only the
jack provided with the vehicle
and in the correct jack position;
never use any other part of the
vehicle for jack support.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 23

10. Remove the lug nuts by turning them
counterclockwise, then remove the
wheel.
11. Mount the spare tire into position and
tighten the nuts by hand. Install the
lug nuts with the beveled edge
inward.
12. Turn the jack handle counterclockwise
and lower the vehicle until it touches
the ground.
Tighten the lug nuts firmly in an “X”
pattern.Once the lug nuts have been tightened,
lower the vehicle fully to the ground and
continue to tighten the lug nuts until they
are completely secured.
If you are unsure of the tightness of the
wheel lug nuts, have them checked at the
nearest service station. The specified
tightening torque is 76 ft. lb (103 N·m).
IN CASE OF EMERGENCY
6-24
1
3
2
4
MMSA6019
MMSA6018
Jack handle
CAUTION
Your vehicle has metric threads on
the wheel studs and nuts. During
wheel removal, make certain that
the same nuts removed are
reinstalled - or, if replaced, that
nuts with metric threads and the
same configuration are used.
Installation of a non-metric thread
nut on a metric stud or vice-versa
will not secure the wheel to the hub
properly and will damage the stud
so that it must be replaced. Note
that most U.S. lug nuts do not have
metric threads. Be sure to use
extreme care in checking for thread
style before installing aftermarket
lug nuts or wheels. If in doubt,
consult an Authorized Kia Dealer.
Damaged studs may result in wheel
loss and personal injury.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 24

MAINTENANCE
7-14ENGINE COOLING
SYSTEMThe cooling system is a high-pressure
type with a reservoir and is filled with
year-round antifreeze coolant at the
factory.
Check the antifreeze protection and
coolant level at least once a year, at the
beginning of the winter season, and
before traveling to a colder climate.
CHECKING THE
COOLANT LEVEL
WARNING - Removing
Radiator Cap
 Never attempt to remove the
radiator cap while the engine
is operating. Doing so might
lead to cooling system
and/or engine damage and
could result in serious
personal injury from
escaping hot coolant or
steam.
 Turn the engine off and wait
until it has cooled. Even then,
use extreme care when
removing the radiator cap.
Wrap a thick towel around it,
and turn it counterclockwise
slowly to the first stop. Step
back while the pressure is
released from the cooling
system. When you are sure
all the pressure has been
released, press down on the
cap, using a thick towel, and
continue turning
counterclockwise to remove
it.
 Even if the engine is not
operating, do not remove the
radiator cap or the drain plug
while the engine and radiator
are hot. Hot coolant and
steam may still blow out
under pressure, causing
serious injury.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 14

7-15
Check the condition and connections of
all cooling system hoses and heater
hoses. Replace any swollen or
deteriorated hoses.
The coolant level should be full in the
radiator and between F (Full) and L
(Low) on the coolant reservoir tank
when the engine is cool.If the coolant level is low, add enough
specified coolant to provide protection
against freezing and corrosion and to
bring the level to F in the coolant
reservoir. Do not overfill. If frequent
additions are required, see an Authorized
Kia Dealer for a cooling system
inspection.
CHANGING COOLANTChange coolant according to the
Scheduled Maintenance.
• Use only soft (de-mineralized) water
in the coolant mixture.
• The engine in your vehicle has
aluminum engine parts and must be
protected by an ethylene glycol-
based coolant to prevent corrosion
and freezing.
• DO NOT USE alcohol or methanol
coolant and do not mix them with the
specified coolant.•Do not use a solution that contains
more than 60% coolant or less than
35% coolaut, which would reduce
the effectiveness of the solution.
For mixture percen-tages, refer to the
following table.
1. Turn the radiator cap counterclockwise
and remove it.
2. Loosen the radiator drain plug and
drain the coolant into a suitable
container.
MMSA7005
Coolant reservoir tank
-15°C (5°F) 35 65
-25°C (-13°F) 40 60
-35°C (-31°F) 50 50
-45°C (-49°F) 60 40Ambient
TemperatureMixture Percentage (volume)
Coolant
SolutionWater
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 15

MAINTENANCE
7-32WHEEL REPLACEMENTWhen replacing the metal wheels for any
reason, make sure the new wheels are
equivalent to the original factory units in
diameter, rim width and offset.
BULB REPLACEMENTHEADLIGHT BULB
REPLACEMENT
1. Remove the headlight bulb cover by
turning it counterclockwise.
2. Disconnect the headlight bulb
electrical connector.
MMSA7024
CAUTION
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, body-to-tire
clearance, snow chain clearance,
speedometer calibration, headlight
aim and bumper height.
WARNING - Halogen
Bulbs

Wear eye protection when
changing a bulb. Allow the
bulb to cool before handling it.
Halogen bulbs contain
pressurized gas. If broken, a
halogen bulb will explode and
will produce flying pieces of
glass.
Always handle halogen bulbs
carefully to avoid scratches
and abrasions. If the bulbs
are lit, avoid contact with
liquids. Never touch the
glass with bare hands.
Residual oil may cause the
bulb to overheat and burst
when lit. A bulb should be
operated only when installed
in the headlight assembly.
If a bulb becomes damaged
or cracked, replace it
immediately and carefully
dispose it.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 32