2006 INFINITI G35 stop start

WARNINGO Do not continue to drive if your vehicle
overheats. Doing so could cause engine
damage or a vehicle fire.
O To avoid the danger of being scalded,
never remove the radiator cap while the
engine is still hot. When the radiator cap
is removed, pressurized hot water will
spurt out, possibly causing serious in-
jury.
O Do not open the hood if steam is coming
out.
If your vehicle is overheating (indicated
by an extremely high temperature gauge
reading), or if you feel a lack of engine
power, detect abnormal noise, etc., take
the following steps:
1. Move the vehicle safely off the road,
apply the parking brake and move the
shift lever to the N (Neutral) position
(automatic transmission to the P
(Park) position).
Do not stop the engine. 2. Turn off the air conditioner. Open all
the windows, and move the tempera-
ture control to maximum hot and the
fan control to high speed.
3. If engine overheating is caused by
climbing a long hill on a hot day, run
the engine at a fast idle (approximately
1,500 rpm) until the temperature gauge
indication returns to normal.
4. Get out of the vehicle. Look and listen
for steam or coolant escaping from the
radiator before opening the hood. (If
steam or coolant is escaping, turn off
the engine.) Do not open the hood fur-
ther until no steam or coolant can be
seen.
5. Open the engine hood.
WARNING If steam or water is coming from the engine,
stand clear to prevent getting burned.
6. Visually check if the cooling fan is run-
ning. The radiator hoses and radiator
should not leak water. If coolant is
leaking or the cooling fan does not
run, stop the engine. WARNING O Be careful not to allow your hands, hair,
jewelry or clothing to come into contact
with, or to get caught in, the engine
belts or the engine cooling fan.
O The engine cooling fan can start at any
time when the coolant temperature is
high.
7. After the engine cools down, check
the coolant level in the reservoir tank
with the engine running. Add coolant
to the reservoir tank if necessary.
Have your vehicle repaired at an
INFINITI dealer.
If needed, Roadside Assistance is avail-
able. Please see your Warranty Information
Booklet or Roadside Assistance I.D. Card
for the toll-free number to call (U.S.) or War-
ranty Information Booklet (Canada).IF YOUR VEHICLE OVERHEATS
In case of emergency
6-11
w 06.1.4/V35-D/V5.0
X

2. Close the radiator drain plug securely
after the coolant is drained.
3. Fill the radiator slowly with the proper
mixture of antifreeze solution and
demineralized water/distilled water.
Fill the reservoir tank up to the MAX
level. Then install the radiator filler
cap.
4. Start the engine and warm it up until
it reaches normal operating tempera-
ture. Then race the engine 2 or 3 times
under no load. Watch the engine cool-
ant temperature gauge for signs of
overheating.
5. Stop the engine. After it completely
cools down, refill the radiator up to
the filler opening. Fill the reservoir
tank up to the MAX level. Check the
drain plug for any sign of leakage.
6. Check the coolant level again after
driving the vehicle.
CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and
apply the parking brake.
2. Run the engine until it reaches operat-
ing temperature.
3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into
the oil pan.
4. Remove the dipstick
q A
and wipe it
clean. Reinsert it all the way. 5. Remove the dipstick again and check
the oil level. It should be between the
H and L marks
q B
. If the oil level is
below the L mark
q A
, remove the oil
filler cap and pour recommended oil
through the opening. Do not overfill
q C
.
6. Recheck oil level with dipstick.
It is normal to add some oil between oil
maintenance intervals or during the break-
in period, depending on the severity of op-
erating conditions. SDI1386D SDI1781
ENGINE OIL
8-10 Maintenance and do-it-yourself
w 06.1.4/V35-D/V5.0
X

REPLACING SPARK PLUGS If replacement is required, see an INFINITI
dealer for servicing.
Platinum-tipped spark plugs It is not necessary to replace the
platinum-tipped
q A
spark plugs as fre-
quently as the conventional type spark
plugs since they will last much longer.
Follow the maintenance schedule in the
INFINITI Service and Maintenance Guide,
but do not reuse them by cleaning or re-
gapping. Always replace with recommended
platinum-tipped spark plugs. If maintenance is required, see an INFINITI
dealer for servicing.
The filter element should not be cleaned
and reused. Replace it according to the
maintenance intervals. See the INFINITI
Service and Maintenance Guide. When re-
placing the filter, wipe the inside of the
air cleaner housing and the cover with a
damp cloth.
WARNING O Operating the engine with the air cleaner
removed can cause you or others to be
burned. The air cleaner not only cleans
the air, it stops the flame if the engine
backfires. If it is not there, and the en-
gine backfires, you could be burned. Do
not drive with the air cleaner removed,
and be careful when working on the en-
gine with the air cleaner removed.
O Never pour fuel into the throttle body or
attempt to start the engine with the air
cleaner removed. Doing so could result
in serious injury.SDI0145D
AIR CLEANER
8-20 Maintenance and do-it-yourself
w 06.1.4/V35-D/V5.0
X

Self-adjusting brakes Your vehicle is equipped with self-
adjusting brakes.
The disc-type brakes self-adjust every
time the brake pedal is applied.
WARNINGSee an INFINITI dealer for a brake system
check if the brake pedal height does not re-
turn to normal.
Brake pad wear indicators The disc brake pads on your vehicle have
audible wear indicators. When a brake pad
requires replacement, it will make a high
pitched scraping or screeching sound when
the vehicle is in motion whether or not the
brake pedal is depressed. Have the brakes
checked as soon as possible if the wear in-
dicator sound is heard.
Under some driving or climate conditions,
occasional brake squeak, squeal or other
noise may be heard. Occasional brake
noise during light to moderate stops is
normal and does not affect the function or
performance of the brake system. Proper brake inspection intervals should
be followed. For additional information,
see the appropriate maintenance log
shown in the INFINITI Service and Mainte-
nance Guide.
High performance sports brake pads oc-
casionally make squeaks, squeals or
other braking noises because of their very
high friction coefficient.
These occasional brake noises are
normal, but if they continue, see an
INFINITI dealer.
BRAKE BOOSTER Check the brake booster function as fol-
lows:
1. With the engine off, press and release
the brake pedal several times. When
brake pedal movement (distance of
travel) remains the same from one
pedal application to the next, continue
on to the next step.
2. While depressing the brake pedal,
start the engine. The pedal height
should drop a little. 3. With the brake pedal depressed, stop
the engine. Keeping the pedal de-
pressed for about 30 seconds, the
pedal height should not change.
4. Run the engine for one minute without
depressing the brake pedal, then turn
it off. Depress the brake pedal several
times. The pedal travel distance will
decrease gradually with each depres-
sion as the vacuum is released from
the booster.
If the brakes do not operate properly, see
an INFINITI dealer.
8-24 Maintenance and do-it-yourself
w 06.1.4/V35-D/V5.0
X

WARNINGNever connect a trailer brake system directly
to the vehicle brake system.
Pre-towing tips O Be certain your vehicle maintains a
level position when a loaded and/or
unloaded trailer is hitched. Do not
drive the vehicle if it has an abnormal
nose-up or nose-down condition;
check for improper tongue load, over-
load, worn suspension or other pos-
sible causes of either condition.
O Always secure items in the trailer to
prevent load shifts while driving.
O Load the trailer so approximately 60%
of the trailer load is in the front half
and 40% is in the back half.
O Check your hitch, trailer tire pressure,
vehicle tire pressure, trailer light op-
eration, and trailer wheel lug nuts
every time you attach a trailer to the
vehicle.
O Be certain your rear view mirrors con-
form to all federal, state or local regula- tions. If not, install any mirrors required
for towing before driving the vehicle.
Trailer towing tips In order to gain skill and an under-
standing of the vehicle's behavior, you
should practice turning, stopping and
backing up in an area which is free from
traffic. Steering stability, and braking per-
formance will be somewhat different than
under normal driving conditions.
O Always secure items in the trailer to
prevent load shift while driving.
O Avoid abrupt starts, acceleration or
stops.
O Avoid sharp turns or lane changes.
O Always drive your vehicle at a mod-
erate speed. Some states or provinces
have specific speed limits for vehicles
that are towing trailers. Obey the local
speed limits.
O When backing up, hold the bottom of
the steering wheel with one hand.
Move your hand in the direction in
which you want the trailer to go. Make
small corrections and back up slowly.
If possible, have someone guide you
when you are backing up. O Always block the wheels on both vehicle
and trailer when parking. Parking on a
slope is not recommended; however, if
you must do so, and if your vehicle is
equipped with automatic transmission,
first apply the parking brake and block
the wheels, and then move the transmis-
sion selector lever into the P (Park) posi-
tion. If you move the selector lever to
the P (Park) position before applying the
parking brake and blocking the wheels,
transmission damage could occur.
O When going down a hill, shift into a
lower gear and use the engine braking
effect. When going up a long grade,
downshift the transmission to a lower
gear and reduce speed to reduce
chances of engine overloading and/or
overheating.
However, for long steep grades, do
not stay in 1st or 2nd gear when
driving above 35 MPH (56 km/h).
O If the engine coolant rises to an ex-
tremely high temperature when the air
conditioning system is on, turn off the
air conditioner. Coolant heat can be
additionally vented by opening the
windows, switching the fan control to
high and setting the temperature con-
trol to the HOT position.
Technical and consumer information
9-21
w 06.1.4/V35-D/V5.0
X

O For emergency towing procedures refer
to ªTowing recommended by INFINITIº in
the ª6. In case of emergencyº section of
this manual.
Automatic transmission To tow a vehicle equipped with an auto-
matic transmission, an appropriate ve-
hicle dolly MUST be placed under the
towed vehicle's drive wheels. Always
follow the dolly manufacturer's recom-
mendations when using their product.
Manual transmission O Always tow with the manual transmis-
sion in Neutral.
O After towing 500 miles, start and idle
the engine with the transmission in
Neutral for two minutes. Failure to idle
the engine after every 500 miles of
towing may cause damage to the
transmission's internal parts. DOT (Department Of Transportation) Qual-
ity Grades: All passenger car tires must
conform to federal safety requirements in
addition to these grades.
Quality grades can be found where appli-
cable on the tire sidewall between tread
shoulder and maximum section width. For
example:
Treadwear 200 Traction AA Temperature A
Treadwear The treadwear grade is a comparative rat-
ing based on the wear rate of the tire
when tested under controlled conditions
on a specified government test course.
For example, a tire graded 150 would wear
one and one-half (1 1/2) times as well on
the government course as a tire graded
100. The relative performance of tires de-
pends upon the actual conditions of their
use, however, and may depart signifi-
cantly from the norm due to variations in
driving habits, service practices and dif-
ferences in road characteristics and cli-
mate.
Traction AA, A, B and C The traction grades, from highest to
lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet
pavement as measured under controlled
conditions on specified government test
surfaces of asphalt and concrete. A tire
marked C may have poor traction perfor-
mance.
WARNING The traction grade assigned to this tire is
based on straight-ahead braking traction
tests, and does not include acceleration, cor-
nering, hydroplaning, or peak traction char-
acteristics.
Temperature A, B and C The temperature grades A (the highest),
B, and C, representing the tire's resis-
tance to the generation of heat and its
ability to dissipate heat when tested
under controlled conditions on a specified
indoor laboratory test wheel. Sustained
high temperature can cause the material
of the tire to degenerate and reduce tire
life, and excessive temperature can lead
to sudden tire failure. The grade C corre-
sponds to a level of performance which
all passenger car tires must meet under
the Federal Motor Safety Standard No.UNIFORM TIRE QUALITY GRADING
Technical and consumer information
9-23
w 06.1.5/V35-D/V5.0
X

A vehicle equipped with All-Wheel Drive
(AWD) should never be tested using a two
wheel dynamometer (such as the dyna-
mometers used by some states for emis-
sions testing), or similar equipment. Make
sure you inform test facility personnel
that your vehicle is equipped with AWD
before it is placed on a dynamometer. Us-
ing the wrong test equipment may result
in transmission damage or unexpected
vehicle movement which could result in
serious vehicle damage or personal in-
jury.
Due to legal requirements in some states/
areas, your vehicle may be required to be
in what is called the ªready conditionº for
an Inspection/Maintenance (I/M) test of
the emission control system.
The vehicle is set to the ªready conditionº
when it is driven through certain driving
patterns. Usually, the ªready conditionº
can be obtained by ordinary usage of the
vehicle.
If a powertrain system component is re-
paired or the battery is disconnected, the
vehicle may be reset to a not ªready con-
ditionº. Before taking the I/M test, check
the vehicle's inspection/maintenance test
readiness condition. Turn the ignition switch ON without starting the engine. If
the Malfunction Indicator Lamp (MIL)
comes on steady for 20 seconds and then
blinks for 10 seconds, the I/M test condi-
tion is ªnot readyº. If the MIL does not
blink after 20 seconds, the I/M test condi-
tion is ªreadyº. If the MIL indicates the
vehicle is in a ªnot readyº condition, drive
the vehicle through the following pattern
to set the vehicle to the ready condition.
If you cannot or do not want to perform
the driving pattern, an INFINITI dealer can
conduct it for you.
WARNING Always drive the vehicle in a safe and pru-
dent manner according to traffic conditions
and obey all traffic laws.
1. Start the engine. Allow the engine to
idle until the engine coolant tempera-
ture gauge needle points between the
C and H (normal operating tempera-
ture).
2. Accelerate the vehicle to 55 MPH (88
km/h), then quickly release the accel-
erator pedal completely and keep it re-
leased for at least 10 seconds. 3. Quickly depress the accelerator pedal
for a moment, then drive the vehicle at
a speed of 53 to 60 MPH (86 to 96
km/h) for at least 9 minutes.
4. Stop the vehicle. Leave the engine
running.
5. Accelerate the vehicle to 35 MPH (55
km/h) and maintain the speed for 20
seconds.
6. Repeat steps 4 and 5 at least 10 times.
7. Accelerate the vehicle to 55 MPH (88
km/h) and maintain the speed for at
least 3 minutes.
8. Stop the vehicle. Place the automatic
transmission selector lever in the ªPº
or ªNº position or the manual trans-
mission shift lever in the ªNº position.
9. Turn the engine off.
10. Repeat steps 1 through 8 at least one
more time.
If step 1 through 7 is interrupted, repeat
the preceding step. Any safe driving mode
is acceptable between steps. Do not stop
the engine until step 7 is completed.READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (US only)
Technical and consumer information
9-25
w 06.1.4/V35-D/V5.0
X

Floor mat cleaning ............................................. 7-4
Fluid
Automatic transmission fluid (ATF)............. 8-13
Brake and clutch fluid ............................... 8-14
Brake fluid ................................................ 8-14
Capacities and recommended fuel/
lubricants ................................................... 9-2
Engine coolant............................................ 8-8
Engine oil .................................................. 8-10
Power steering fluid .................................. 8-13
Window washer fluid ................................. 8-15
FM-AM-SATELLITE radio with compact disc (CD)
changer ........................................................... 4-22
Fog light switch ............................................... 2-25
Front passenger air bag and status light.......... 1-44
Front power seat adjustment .............................. 1-2
Fuel
Capacities and recommended fuel/
lubricants ................................................... 9-2
Fuel economy ............................................ 5-22
Fuel economy information (display) ............ 4-4
Fuel-filler cap ............................................ 3-28
Fuel-filler door .......................................... 3-28
Fuel octane rating ....................................... 9-3
Fuel recommendation.................................. 9-3
Gauge ......................................................... 2-5
Fuses ............................................................... 8-25
Fusible links .................................................... 8-26
G
Garage door opener, HomeLink Universal
Transceiver ...................................................... 2-46
Gas cap ........................................................... 3-28 Gauge................................................................ 2-3
Engine coolant temperature gauge.............. 2-4
Fuel gauge .................................................. 2-5
Odometer.................................................... 2-3
Speedometer .............................................. 2-3
Tachometer ................................................. 2-4
General maintenance ......................................... 8-2
Glove box ........................................................ 2-35
Glove box (upper) ............................................ 2-35
Glove box lock ................................................. 2-35
Golf bag stowing ............................................. 2-39
H
Hands-Free Phone System, Bluetooth ............ 4-30
Hazard warning flasher switch ......................... 2-25
Head restraints .................................................. 1-8
Headlights
Bulb replacement...................................... 8-33
Headlight switch........................................ 2-21
Xenon headlights ...................................... 2-21
Heated seats ................................................... 2-26
Heater
Engine block heater .................................. 5-32
Heater and air conditioner (automatic) ...... 4-10
HomeLink Universal Transceiver .................... 2-46
Hood release ................................................... 3-24
Hook, Coat hook.............................................. 2-38
Horn ................................................................ 2-26
How to stop alarm, Vehicle security ................. 2-18 I
Ignition switch
(except Intelligent Key system) ................... 5-6
Automatic transmission models .......... 5-6, 5-12
Key positions .............................................. 5-8
Manual transmission models .............. 5-7, 5-16
Immobilizer system .......................................... 2-18
In-cabin microfilter ........................................... 4-13
Indicator lights ................................................. 2-14
INFINITI Vehicle Immobilizer System
Engine start ........................................ 5-8, 5-10
Inside
Automatic anti-glare mirror ....................... 3-32
Inspection/maintenance (I/M) test ................... 9-25
Instrument brightness control .......................... 2-24
Instrument panel ............................................... 2-2
Instrument pocket ............................................ 2-31
Intelligent Key system
Engine starting .......................................... 3-14
Key operating range .................................. 3-16
Key operation............................................. 3-11
Mechanical key and valet key ................... 3-23
Operating the engine................................. 3-14
Remote keyless operation ......................... 3-20
Trouble-shooting guide .............................. 3-19
Warning light............................................. 2-12
Warning signals ......................................... 3-17
Intelligent Key warning light............................. 2-12
Interior light replacement ................................ 8-33
Interior lights .................................................. 2-44
Interior trunk lid release .................................. 3-27
ISOFIX child restraint........................................ 1-25
10-3
w 06.1.5/V35-D/V5.0
X