2006 INFINITI G35 child lock

CHILD RESTRAINT INSTALLATION
ON FRONT PASSENGER SEAT
WARNINGO Never install a rear-facing child restraint
in the front passenger seat. Supple-
mental front air bags inflate with great
force. A rear-facing child restraint could
be struck by the supplemental front air
bag in a crash and could seriously injure
or kill your child. O INFINITI recommends that child re-
straints be installed in the rear seat.
However, if you must install a front-
facing child restraint in the front passen-
ger seat, move the passenger seat to the
rearmost position. Also, be sure the front
passenger air bag status light is illumi-
nated to indicate the passenger air bag
is OFF. See ªFront passenger air bag and
status lightº later in this section for
details. O A child restraint with a top tether strap
should not be used in the front pas-
senger seat.
O The three-point seat belt in your vehicle
is equipped with an automatic locking
mode retractor which must be used
when installing a child restraint.
O Failure to use the retractor's locking
mode will result in the child restraint not
being properly secured. The restraint
could tip over or otherwise be unsecured
and cause injury to the child in a sudden
stop or collision. Also, it can change the
operation of the front passenger air bag.
See ªFront passenger air bag and status
lightº later in this section. SSS0300A
1-28 Safety Ð Seats, seat belts and supplemental restraint system
w 06.1.4/V35-D/V5.0
X

3. Pull on the shoulder belt until all of
the belt is fully extended. At this time,
the belt retractor is in the automatic
locking mode (child restraint mode). It
reverts back to emergency locking
mode when the belt is fully retracted. 4. Allow the seat belt to retract. Pull up
the shoulder belt to remove any slack
in the belt. 5. Before placing the child in the child
restraint, use force to push the child
restraint from side to side, and tug it
forward to make sure that it is se-
curely held in place. It should not
move more than 1 inch (25 mm). If it
does move more than 1 inch (25 mm),
pull again on the shoulder belt to fur-
ther tighten the child restraint. If un-
able to properly secure the restraint,
move the restraint to another rear
seating position and try again, or try a
different child restraint. Not all child
restraints fit in all types of vehicles.SSS0361 SSS0424 SSS0302E
1-30 Safety Ð Seats, seat belts and supplemental restraint system
w 06.1.4/V35-D/V5.0
X

6. Check that the retractor is in the auto-
matic locking mode by trying to pull
more belt out of the retractor. If you
cannot pull any more belt webbing out
of the retractor, the retractor is in the
automatic locking mode.
7. Check to make sure that the child re-
straint is properly secured prior to
each use. If the seat belt is not
locked, repeat steps 3 through 7.
8. Turn the ignition switch to the ON po-
sition. The passenger air bag status
light should illuminate. If this
light is not illuminated, see ªFront
passenger air bag and status lightº
later in this section. Move the child re-
straint to another seating position.
Have the system checked by an IN-
FINITI dealer.
After the child restraint is removed and
the seat belt is fully retracted, the auto-
matic locking mode (child restraint mode)
will be canceled. PRECAUTIONS ON BOOSTER SEATS
WARNING O Infants and small children should always
be placed in an appropriate child re-
straint while riding in the vehicle. Failure
to use a child restraint or booster seat
can result in serious injury or death.
O Infants and small children should never
be carried on your lap. It is not possible
for even the strongest adult to resist the
forces of a severe accident. The child
could be crushed between the adult and
parts of the vehicle. Also, do not put the
same seat belt around both your child
and yourself.
O INFINITI recommends that the booster
seat be installed in the rear seat. Accord-
ing to accident statistics, children are
safer when properly restrained in the
rear seat than in the front seat.
O A booster seat must only be installed in
a seating position that has a
lap/shoulder belt. Failure to use a three- point type seat belt with a booster seat
can result in a serious injury in sudden
stop or collision.
O An improperly installed booster seat
could lead to serious injury or death in
an accident.
BOOSTER SEATS
Safety Ð Seats, seat belts and supplemental restraint system
1-31
w 06.1.4/V35-D/V5.0
X

BOOSTER SEAT INSTALLATION ON
REAR SEAT OUTBOARD OR CENTER
POSITIONS
CAUTIONDo not use a lap/shoulder belt automatic
locking mode when using a booster seat
with the seat belts.
When you install a booster seat in the
rear seat, follow these steps: 1. Position the booster seat on the seat.
Only place it in a front-facing direc-
tion. Always follow the booster seat
manufacturer's instructions.
2. The booster seat should be positioned
on the vehicle seat so that it is stable.
If necessary, adjust or remove the
head restraint to obtain the correct
booster seat fit. See ªHead restraint
adjustmentº earlier in this section. If
the head restraint is removed, store it
in a secure place. Be sure to install
the head restraint when the booster
seat is removed. If the seating posi-
tion does not have an adjustable head restraint and it is interfering with the
proper booster seat fit, try another
seating position or a different booster
seat.
3. Position the lap portion of the seat
belt low and snug on the child's hips.
Be sure to follow the booster seat
manufacturer's instructions for ad-
justing the belt routing.
4. Pull the shoulder belt portion of the
seat belt toward the retractor to take
up extra slack. Be sure the shoulder
belt is positioned across the top,
middle portion of the child's shoulder.
Be sure to follow the booster seat
manufacturer's instructions for ad-
justing the belt routing.
5. Follow the warnings, cautions and in-
structions for properly fastening a seat
belt shown in the ªThree-point type
seat belts with retractorº earlier in
this section.LRS0452
Outboard position LRS0451
Center position
1-34 Safety Ð Seats, seat belts and supplemental restraint system
w 06.1.4/V35-D/V5.0
X

all instructions in this manual concerning
the use of seats, seat belts and child re-
straints can increase the risk or severity of
injury in an accident.
Status light:
The front passenger air bag status light
is located in the center display. The
light operates as follows:
O Unoccupied passenger seat: The is
OFF and the front passenger air bag is
OFF and will not inflate in a crash.
O Passenger seat occupied by a small
adult, child or child restraint as out-
lined in this section: The illumi-
nates to indicate that the front pas-
senger air bag is OFF and will not in-
flate in a crash.
O Occupied passenger seat and the pas-
senger meets the conditions outlined
in this section: The light is OFF to
indicate that the front passenger air
bag is operational.
Front passenger air bag:
The front passenger air bag is designed to
automatically turn OFF when the vehicle is operated under some conditions as de-
scribed below in accordance with U.S.
regulations. If the front passenger air bag
is OFF, it will not inflate in a crash. The
driver air bag and other air bags in your
vehicle are not part of this system.
The purpose of the regulation is to help
reduce the risk of injury or death from an
inflating air bag to certain front passenger
seat occupants, such as children, by re-
quiring the air bag to be automatically
turned OFF. Certain sensors are used to
meet the requirements.
One sensor used is the occupant classifi-
cation sensor (pressure sensor). It is in
the bottom of the front passenger seat
cushion and is designed to detect an oc-
cupant and objects on the seat by weight.
It works together with seat belt sensors
described later. For example, if a child is
in the front passenger seat, the advanced
air bag system is designed to turn the
passenger air bag OFF in accordance with
the regulations. Also, if a child restraint of
the type specified in the regulations is on
the seat, its weight and the child's weight
can be detected and cause the air bag to
turn OFF. Occupant classification sensor
operation can vary depending on the front
passenger seat belt sensors. The front passenger seat belt sensors are
designed to detect if the seat belt is
buckled and the amount of tension on the
seat belt, such as when it is in the auto-
matic locking mode (child restraint mode).
Based on the weight on the seat detected
by the occupant classification sensor and
the belt tension detected on the seat belt,
the INFINITI advanced air bag system de-
termines whether the front passenger air
bag should be automatically turned OFF
as required by the regulations.
Front passenger seat adult occupants who
are properly seated and using the seat
belt as outlined in this manual should not
cause the passenger air bag to be auto-
matically turned OFF. For small adults it
may be turned OFF, however, if the occu-
pant takes his/her weight off the seat
cushion (for example, by not sitting up-
right, by sitting on an edge of the seat, or
by otherwise being out of position), this
could cause the sensor to turn the air bag
OFF. In addition, if the occupant improp-
erly uses the seat belt in the automatic
locking mode (child restraint mode), this
could cause the air bag to be turned OFF.
Always be sure to be seated and wearing
the seat belt properly for the most effec-
tive protection by the seat belt and
supplemental air bag.
Safety Ð Seats, seat belts and supplemental restraint system
1-45
w 06.1.4/V35-D/V5.0
X

INFINITI recommends that pre-teens and
children be properly restrained in a rear
seat. INFINITI also recommends that ap-
propriate child restraints and booster
seats be properly installed in a rear seat.
If this is not possible, the occupant clas-
sification sensor and seat belt sensors
are designed to operate as described
above to turn the front passenger air bag
OFF for specified child restraints as re-
quired by the regulations. Failing to prop-
erly secure child restrains and to use the
automatic locking mode (child restraint
mode) may allow the restraint to tip or
move in an accident or sudden stop. This
can also result in the passenger air bag
inflating in a crash instead of being OFF.
See ªChild restraintsº earlier in this sec-
tion for proper use and installation.
If the front passenger seat is not occu-
pied, the passenger air bag is designed
not to inflate in a crash. However, heavy
objects placed on the seat could result in
air bag inflation, because of the object's
weight detected by the occupant classifi-
cation sensor. Other conditions could also
result in air bag inflation, such as if a
child is standing on the seat, or if two
children are on the seat, contrary to the
instructions in this manual. Always be sure that you and all vehicle occupants
are seated and restrained properly.
Using the passenger air bag status light,
you can monitor when the front pas-
senger air bag is automatically turned OFF
with the seat occupied. The light will not
illuminate when the front passenger seat
is unoccupied.
If an adult occupant is in the seat but the
passenger air bag status light is illumi-
nated (indicating that the air bag is OFF),
it could be that the person is a small
adult, or is not sitting on the seat prop-
erly or is not using the seat belt properly.
If a child restraint must be used in the
front seat, the passenger air bag status
light may or may not be illuminated, de-
pending on the size of the child and the
type of child restraint being used. If the
passenger air bag status light is not illu-
minated (indicating that the air bag might
inflate in a crash), it could be that the
child restraint or seat belt is not being
used properly. In rare cases, the pas-
senger air bag status light will not illumi-
nate even though the air bag is OFF.
If such situations happen, properly posi-
tion and restrain the occupant or child re-
straint. Otherwise reposition the occupant or child restraint in a rear seat. If you
have any questions about whether your
passenger air bag is working as designed,
your INFINITI dealer can confirm that it is
working properly by using a special tool.
The INFINITI advanced air bag system and
passenger air bag status light will take a
few seconds to register a change in the
passenger seat status. For example, if a
large adult who is sitting in the front pas-
senger seat exits the vehicle, the passen-
ger air bag status light will change from
OFF to ON for a few seconds and then to
OFF. This is normal system operation and
does not indicate a malfunction.
If a malfunction occurs in the front pas-
senger air bag system, the supplemental
air bag warning light , located in the
meter and gauges area will blink. Have
the system checked by an INFINITI dealer.
1-46 Safety Ð Seats, seat belts and supplemental restraint system
w 06.1.4/V35-D/V5.0
X

STOWING GOLF BAGS (Coupe) Normally, two standard golf bags can be
stowed in the trunk. Insert the top of the
golf bag into left side of the trunk room
q 1
then put the bag forward
q 2
. Insert
the top of the 2nd golf bag into right side
of the trunk room
q 3
and pull it in all the
way
q 4
.
In some cases, you may not be able to
stow two golf bags in your vehicle, de-
pending on their sizes or types. POWER WINDOWS
WARNING O Make sure that all passengers have their
hands, etc. inside the vehicle while it is
in motion and before closing the win-
dows. Use the window lock switch to
prevent unexpected use of the power
windows.
O Do not leave children unattended inside
the vehicle. They could unknowingly ac-
tivate switches or controls and become
trapped in a window. Unattended chil-
dren could become involved in serious
accidents.
The power windows operate when the ig-
nition key is in the ON position and for
about 45 seconds, after the ignition
switch is turned to the OFF position. If the
driver's door or the front passenger's
door is opened during this period of
about 45 seconds, power to the windows
is canceled. Main power window switch
(driver's side) 1. Driver side window
2. Front passenger side window
3. Rear left passenger side window
4. Rear right passenger side window
5. Window lock button
To open or close the window, push down
q A
or pull up
q B
the switch and hold it.
The main switch (driver side switches) will
open or close all the windows.SIC2209 SIC2576
Sedan Ð Main switchWINDOWS
Instruments and controls
2-39
w 06.1.4/V35-D/V5.0
X

3 Pre-driving checks and adjustments Keys ................................................................. 3-2
Infiniti vehicle immobilizer system keys ...... 3-2
Doors ............................................................... 3-3
Locking with key ......................................... 3-3
Locking with inside lock knob ..................... 3-4
Locking with power door lock switch........... 3-4
Child safety rear door lock (Sedan) ............. 3-5
Remote keyless entry system (models without
Intelligent Key system) ..................................... 3-5
How to use remote keyless entry system .... 3-6
Intelligent Key system (if so equipped) ............. 3-9
Door locks/unlocks precaution .................. 3-11
Intelligent Key operation ............................ 3-11
Opening and closing windows ................... 3-14
Operating the engine ................................. 3-14
Intelligent Key operating range ................. 3-16
Warning signals ......................................... 3-17
Trouble-shooting guide .............................. 3-19
Operation with intelligent remote keyless
entry system ............................................. 3-20
Operation with the mechanical key and
valet key ................................................... 3-23 Hood .............................................................. 3-24
Trunk lid ......................................................... 3-25
Opener operation ...................................... 3-25
Interior trunk lid release ............................ 3-27
Secondary trunk lid release ....................... 3-27
Fuel-filler door ................................................ 3-28
Opening the fuel-filler door ....................... 3-28
Fuel-filler cap ............................................ 3-29
Steering wheel ............................................... 3-30
Manual operation ...................................... 3-30
Electric operation (if so equipped) ............. 3-31
Sun visors ...................................................... 3-32
Mirrors............................................................ 3-32
Automatic anti-glare inside mirror (if so
equipped) .................................................. 3-32
Outside mirrors ......................................... 3-33
Automatic drive positioner (if so equipped) .... 3-34
Automatic drive positioner operation ......... 3-34
Entry/exit function (if so equipped) ........... 3-34
Memory storage function ........................... 3-35
System operation ...................................... 3-36
Cancel switch (if so equipped)................... 3-37
w 06.1.4/V35-D/V5.0
X