ON BOARD DIAGNOSTIC (OBD) SYSTEM EC-71
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 December 2006 FX35/FX45
DIAGNOSTIC TEST MODE II — SELF-DIAGNOSTIC RESULTS
In this mode, the DTC and 1st trip DTC are indicated by the number of blinks of the MIL as shown below.
The DTC and 1st trip DTC are displayed at the same time. If the MIL does not illuminate in diagnostic test
mode I (Malfunction warning), all displayed items are 1st trip DTCs. If only one code is displayed when the MIL
illuminates in diagnostic test mode II (SELF-DIAGNOSTIC RESULTS), it is a DTC; if two or more codes are
displayed, they may be either DTCs or 1st trip DTCs. DTC No. is same as that of 1st trip DTC. These uniden-
tified codes can be identified by using the CONSULT-II or GST. A DTC will be used as an example for how to
read a code.
A particular trouble code can be identified by the number of four-digit numeral flashes. The “zero” is indicated
by the number of ten flashes. The “A” is indicated by the number of eleven flash. The length of time the
1,000th-digit numeral flashes on and off is 1.2 seconds consisting of an ON (0.6-second) - OFF (0.6-second)
cycle.
The 100th-digit numeral and lower digit numerals consist of a 0.3-second ON and 0.3-second OFF cycle.
A change from one digit numeral to another occurs at an interval of 1.0-second OFF. In other words, the later
numeral appears on the display 1.3 seconds after the former numeral has disappeared.
A change from one trouble code to another occurs at an interval of 1.8-second OFF.
In this way, all the detected malfunctions are classified by their DTC numbers. The DTC 0000 refers to no mal-
function. (See EC-15, "
INDEX FOR DTC" )
How to Erase Diagnostic Test Mode II (Self-diagnostic Results)
The DTC can be erased from the back up memory in the ECM by depressing accelerator pedal. Refer to EC-
69, "How to Set Diagnostic Test Mode II (Self-Diagnostic Results)" .
If the battery is disconnected, the DTC will be lost from the backup memory within 24 hours.
Be careful not to erase the stored memory before starting trouble diagnoses.
PBIB3005E
EC-122
[VQ35DE]
TROUBLE DIAGNOSIS
Revision: 2006 December 2006 FX35/FX45
*: This function is not necessary in the usual service procedure.
SELF-DIAG RESULTS MODE
Self Diagnostic Item
Regarding items of DTC and 1st trip DTC, refer to EC-55, "EMISSION-RELATED DIAGNOSTIC INFORMA-
TION ITEMS" .
Freeze Frame Data and 1st Trip Freeze Frame Data
EVAP SYSTEM CLOSE CLOSE THE EVAP CANISTER VENT CONTROL VALVE IN
ORDER TO MAKE EVAP SYSTEM CLOSE UNDER THE
FOLLOWING CONDITIONS.
IGN SW ON
ENGINE NOT RUNNING
AMBIENT TEMPERATURE IS ABOVE 0 °C (32 °F).
NO VACUUM AND NO HIGH PRESSURE IN EVAP SYS-
TEM
FUEL TANK TEMP. IS MORE THAN 0 °C (32 °F).
WITHIN 10 MINUTES AFTER STARTING “EVAP SYS-
TEM CLOSE”
WHEN TRYING TO EXECUTE “EVAP SYSTEM CLOSE”
UNDER THE CONDITION EXCEPT ABOVE, CONSULT-
II WILL DISCONTINUE IT AND DISPLAY APPROPRI-
ATE INSTRUCTION.
NOTE:
WHEN STARTING ENGINE, CONSULT-II MAY DISPLAY
“BATTERY VOLTAGE IS LOW. CHARGE BATTERY”,
EVEN IN USING CHARGED BATTERY. When detecting EVAP vapor leak
point of EVAP system
VIN REGISTRATION
IN THIS MODE VIN IS REGISTERED IN ECM When registering VIN is ECM
TARGET IDLE RPM ADJ*
IDLE CONDITION When setting target idle speed
TARGET IGN TIM ADJ*
IDLE CONDITION When adjusting target ignition tim- ing
WORK ITEM CONDITION USAGE
Freeze frame data
item* Description
DIAG TROUBLE
CODE
[PXXXX]
The engine control component part/control system has a trouble code, it is displayed as “PXXXX”. (Refer
to EC-15, "
INDEX FOR DTC" .)
FUEL SYS-B1
“Fuel injection system status” at the moment a malfunction is detected is displayed.
One mode in the following is displayed.
“Mode2”: Open loop due to detected system malfunction
“Mode3”: Open loop due to driving conditions (power enrichment, deceleration enleanment)
“Mode4”: Closed loop - using oxygen sensor(s) as feedback for fuel control
“Mode5”: Open loop - has not yet satisfied condition to go to closed loop
FUEL SYS-B2
CAL/LD VALUE [%]
The calculated load value at the moment a malfunction is detected is displayed.
COOLANT TEMP
[ ° C] or [ °F]
The engine coolant temperature at the moment a malfunction is detected is displayed.
L-FUEL TRM-B1 [%]
“Long-term fuel trim” at the moment a malfunction is detected is displayed.
The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule
than short-term fuel trim.
L-FUEL TRM-B2 [%]
S-FUEL TRM-B1 [%]
“Short-term fuel trim” at the moment a malfunction is detected is displayed.
The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel
schedule.
S-FUEL TRM-B2 [%]
ENGINE SPEED
[rpm]
The engine speed at the moment a malfunction is detected is displayed.
EC-258
[VQ35DE]
DTC P0133, P0153 A/F SENSOR 1
Revision: 2006 December 2006 FX35/FX45
DTC P0133, P0153 A/F SENSOR 1PFP:22693
Component DescriptionNBS003W3
The air fuel ratio (A/F) sensor 1 is a planar dual-cell limit current sen-
sor. The sensor element of the air fuel ratio (A/F) sensor 1 is the
combination of a Nernst concentration cell (sensor cell) with an oxy-
gen-pump cell, which transports ions. It has a heater in the element.
The sensor is capable of precise measurement = 1, but also in the
lean and rich range. Together with its control electronics, the sensor
outputs a clear, continuous signal throughout a wide range (0.7 < < air).
The exhaust gas components diffuse through the diffusion gap at the
electrode of the oxygen pump and Nernst concentration cell, where
they are brought to thermodynamic balance.
An electronic circuit controls the pump current through the oxygen-
pump cell so that the composition of the exhaust gas in the diffusion
gap remains constant at = 1. Therefore, the air fuel ratio (A/F) sen-
sor 1 is able to indicate air/fuel ratio by this pumping of current. In
addition, a heater is integrated in the sensor to ensure the required
operating temperature of 700 - 800 °C (1,292 - 1,472 °F).
CONSULT-II Reference Value in Data Monitor ModeNBS003W4
Specification data are reference values.
On Board Diagnosis LogicNBS003W5
To judge the malfunction of air fuel ratio (A/F) sensor 1, this diagnosis measures response time of the A/F sig-
nal computed by ECM from the air fuel ratio (A/F) sensor 1 signal. The time is compensated by engine operat-
ing (speed and load), fuel feedback control constant, and the air fuel ratio (A/F) sensor 1 temperature index.
Judgment is based on whether the compensated time (the A/F signal cycling time index) is inordinately long or
not.
SEF579Z
SEF580Z
MONITOR ITEM CONDITION SPECIFICATION
A/F SEN1 (B1)
A/F SEN1 (B2)
Engine: After warming up Maintaining engine speed at
2,000 rpm Fluctuates around 1.5V
DTC No. Trouble diagnosis name DTC detecting condition Possible Cause
P0133
0133
(Bank 1)
Air fuel ratio (A/F) sensor 1
circuit slow response The response of the A/F signal computed by
ECM from air fuel ratio (A/F) sensor 1 signal
takes more than the specified time.
Harness or connectors
[Air fuel ratio (A/F) sensor 1 circuit
is open or shorted.]
Air fuel ratio (A/F) sensor 1
Air fuel ratio (A/F) sensor 1 heater
Fuel pressure
Fuel injector
Intake air leaks
Exhaust gas leaks
PCV
Mass air flow sensor
P0153
0153
(Bank 2)
EC-676
[VK45DE]
INDEX FOR DTC
Revision: 2006 December 2006 FX35/FX45
[VK45DE]INDEX FOR DTCPFP:00024
DTC No. IndexNBS004JK
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-819, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010. Refer
to EC-822, "
DTC U1010 CAN COMMUNICATION" .
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3
U1000 1000*4CAN COMM CIRCUIT EC-819
U1001
1001*4CAN COMM CIRCUIT EC-819
U1010 1010 CONTROL UNIT(CAN) EC-822
P0000 0000 NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED. —
P0011 0011 INT/V TIM CONT-B1 EC-824
P0021 0021 INT/V TIM CONT-B2 EC-824
P0031 0031 A/F SEN1 HTR (B1)EC-836
P0032 0032 A/F SEN1 HTR (B1)EC-836
P0037 0037 HO2S2 HTR (B1)EC-843
P0038 0038 HO2S2 HTR (B1)EC-843
P0051 0051 A/F SEN1 HTR (B2)EC-836
P0052 0052 A/F SEN1 HTR (B2)EC-836
P0057 0057 HO2S2 HTR (B2)EC-843
P0058 0058 HO2S2 HTR (B2)EC-843
P0075 0075 INT/V TIM V/CIR-B1EC-851
P0081 0081 INT/V TIM V/CIR-B2EC-851
P0101 0101 MAF SEN/CIRCUITEC-858
P0102 0102 MAF SEN/CIRCUITEC-867
P0103 0103 MAF SEN/CIRCUITEC-867
P0112 0112 IAT SEN/CIRCUITEC-874
P0113 0113 IAT SEN/CIRCUITEC-874
P0117 0117 ECT SEN/CIRCEC-879
P0118 0118 ECT SEN/CIRCEC-879
P0122 0122 TP SEN2/CIRC EC-885
P0123 0123 TP SEN2/CIRCEC-885
P0125 0125 ECT SENSOREC-892
P0127 0127 IAT SENSOREC-895
P0128 0128 THERMSTAT FNCTNEC-898
P0130 0130 A/F SENSOR1 (B1)EC-900
P0131 0131 A/F SENSOR1 (B1)EC-910
P0132 0132 A/F SENSOR1 (B1)EC-919
P0133 0133 A/F SENSOR1 (B1)EC-928
P0137 0137 HO2S2 (B1)EC-940
P0138 0138 HO2S2 (B1)EC-951
INDEX FOR DTC EC-677
[VK45DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 December 2006 FX35/FX45P0139 0139 HO2S2 (B1) EC-964
P0150 0150 A/F SENSOR1 (B2)EC-900
P0151 0151 A/F SENSOR1 (B2)EC-910
P0152 0152 A/F SENSOR1 (B2)EC-919
P0153 0153 A/F SENSOR1 (B2)EC-928
P0157 0157 HO2S2 (B2)EC-940
P0158 0158 HO2S2 (B2)EC-951
P0159 0159 HO2S2 (B2)EC-964
P0171 0171 FUEL SYS-LEAN-B1EC-975
P0172 0172 FUEL SYS-RICH-B1EC-986
P0174 0174 FUEL SYS-LEAN-B2EC-975
P0175 0175 FUEL SYS-RICH-B2EC-986
P0181 0181 FTT SENSOREC-997
P0182 0182 FTT SEN/CIRCUITEC-1003
P0183 0183 FTT SEN/CIRCUITEC-1003
P0222 0222 TP SEN 1/CIRCEC-1008
P0223 0223 TP SEN 1/CIRCEC-1008
P0300 0300 MULTI CYL MISFIREEC-1015
P0301 0301 CYL 1 MISFIREEC-1015
P0302 0302 CYL 2 MISFIREEC-1015
P0303 0303 CYL 3 MISFIREEC-1015
P0304 0304 CYL 4 MISFIREEC-1015
P0305 0305 CYL 5 MISFIREEC-1015
P0306 0306 CYL 6 MISFIREEC-1015
P0307 0307 CYL 7 MISFIREEC-1015
P0308 0308 CYL 8 MISFIREEC-1015
P0327 0327 KNOCK SEN/CIRC-B1EC-1025
P0328 0328 KNOCK SEN/CIRC-B1EC-1025
P0332 0332 KNOCK SEN/CIRC-B2EC-1025
P0333 0333 KNOCK SEN/CIRC-B2EC-1025
P0335 0335 CKP SEN/CIRCUITEC-1030
P0340 0340 CMP SEN/CIRC-B1EC-1037
P0420 0420 TW CATALYST SYS-B1EC-1044
P0430 0430 TW CATALYST SYS-B2EC-1044
P0441 0441 EVAP PURG FLOW/MONEC-1049
P0442 0442 EVAP SMALL LEAKEC-1054
P0443 0443 PURG VOLUME CONT/VEC-1063
P0444 0444 PURG VOLUME CONT/VEC-1071
P0445 0445 PURG VOLUME CONT/VEC-1071
P0447 0447 VENT CONTROL VALVEEC-1078
P0448 0448 VENT CONTROL VALVEEC-1085
P0451 0451 EVAP SYS PRES SENEC-1091
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3
EC-678
[VK45DE]
INDEX FOR DTC
Revision: 2006 December 2006 FX35/FX45
P0452 0452 EVAP SYS PRES SEN EC-1094
P0453 0453 EVAP SYS PRES SEN EC-1100
P0455 0455 EVAP GROSS LEAKEC-1108
P0456 0456 EVAP VERY SML LEAK E C - 111 6
P0460 0460 FUEL LEV SEN SLOSHEC-1125
P0461 0461 FUEL LEVEL SENSOREC-1127
P0462 0462 FUEL LEVL SEN/CIRCEC-1129
P0463 0463 FUEL LEVL SEN/CIRCEC-1129
P0500 0500
VEH SPEED SEN/CIRC*5EC-1131
P0506 0506 ISC SYSTEM EC-1133
P0507 0507 ISC SYSTEMEC-1135
P0550 0550 PW ST P SEN/CIRCEC-1137
P0603 0603 ECM BACK UP/CIRCUITEC-1142
P0605 0605 ECMEC-1146
P0643 0643 SENSOR POWER/CIRCEC-1149
P0700 0700 TCM AT- 111
P0705 0705 PNP SW/CIRCAT- 11 2
P0710 0710 ATF TEMP SEN/CIRCAT-134
P0717 0717 TURBINE SENSOR AT- 11 6
P0720 0720
VEH SPD SEN/CIR AT*5AT- 11 8
P0740 0740 TCC SOLENOID/CIRC AT-125
P0744 0744 A/T TCC S/V FNCTNAT-127
P0745 0745 L/PRESS SOL/CIRCAT-129
P0850 0850 P-N POS SW/CIRCUITEC-1154
P1140 1140 INTK TIM S/CIRC-B1EC-1159
P1145 1145 INTK TIM S/CIRC-B2EC-1159
P1148 1148 CLOSED LOOP-B1EC-1168
P1168 1168 CLOSED LOOP-B2EC-1168
P1211 1211 TCS C/U FUNCTNEC-1169
P1212 1212 TCS/CIRC EC-1170
P1217 1217 ENG OVER TEMPEC-1171
P1225 1225 CTP LEARNINGEC-1183
P1226 1226 CTP LEARNINGEC-1185
P1564 1564 ASCD SW EC-1187 (Models with ICC)
EC-1194
(Models with ASCD)
P1568 1568 ACC COMMAND VALUE*
6EC-1201
P1572 1572 ASCD BRAKE SW EC-1202 (Models with ICC)
EC-1211
(Models with ASCD)
P1574 1574 ASCD VHL SPD SEN EC-1219
(Models with ICC)
EC-1221
(Models with ASCD)
P1610 - P1615 1610 - 1615 NATS MALFUNCTION EC-713
P1715 1715 IN PULY SPEEDEC-1223
P1730 1730 A/T INTERLOCK AT-141
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3
INDEX FOR DTC EC-679
[VK45DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 December 2006 FX35/FX45
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*6: Models with ICC. P1752 1752 I/C SOLENOID/CIRC
AT-146
P1754 1754 I/C SOLENOID FNCTNAT-148
P1757 1757 FR/B SOLENOID/CIRCAT-150
P1759 1759 FR/B SOLENOID FNCTAT-152
P1762 1762 D/C SOLENOID/CIRCAT-154
P1764 1764 D/C SOLENOID FNCTNAT-156
P1767 1767 HLR/C SOL/CIRCAT-158
P1769 1769 HLR/C SOL FNCTNAT-160
P1772 1772 LC/B SOLENOID/CIRCAT-162
P1774 1774 LC/B SOLENOID FNCTAT-164
P1800 1800 VIAS S/V CIRCEC-1224
P1805 1805 BRAKE SW/CIRCUITEC-1229
P2100 2100 ETC MOT PWREC-1234
P2101 2101 ETC FUNCTION/CIRCEC-1240
P2103 2103 ETC MOT PWREC-1234
P 2 11 8 2 11 8 E T C M O TEC-1247
P 2 11 9 2 11 9 E T C A C T REC-1252
P2122 2122 APP SEN 1/CIRC EC-1254
P2123 2123 APP SEN 1/CIRCEC-1254
P2127 2127 APP SEN 2/CIRCEC-1261
P2128 2128 APP SEN 2/CIRCEC-1261
P2135 2135 TP SENSOREC-1268
P2138 2138 APP SENSOREC-1275
P2A00 2A00 A/F SENSOR1 (B1) EC-1283
P2A03 2A03 A/F SENSOR1 (B2)EC-1283
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3
EC-680
[VK45DE]
INDEX FOR DTC
Revision: 2006 December 2006 FX35/FX45
Alphabetical IndexNBS004JL
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-819, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010. Refer
to EC-822, "
DTC U1010 CAN COMMUNICATION" .
Items
(CONSULT-II screen terms) DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SEN1 HTR (B1) P0031 0031 EC-836
A/F SEN1 HTR (B1) P0032 0032EC-836
A/F SEN1 HTR (B2) P0051 0051EC-836
A/F SEN1 HTR (B2) P0052 0052EC-836
A/F SENSOR1 (B1) P0130 0130EC-900
A/F SENSOR1 (B1) P0131 0131EC-910
A/F SENSOR1 (B1) P0132 0132EC-919
A/F SENSOR1 (B1) P0133 0133EC-928
A/F SENSOR1 (B1) P2A00 2A00EC-1283
A/F SENSOR1 (B2) P0150 0150 EC-900
A/F SENSOR1 (B2) P0151 0151EC-910
A/F SENSOR1 (B2) P0152 0152EC-919
A/F SENSOR1 (B2) P0153 0153EC-928
A/F SENSOR1 (B2) P2A03 2A03EC-1283
A/T INTERLOCK P1730 1730 AT- 1 4 1
A/T TCC S/V FNCTN P0744 0744AT- 1 2 7
ACC COMMAND VALUE*6P1568 1568EC-1201
APP SEN 1/CIRC P2122 2122 EC-1254
APP SEN 1/CIRC P2123 2123EC-1254
APP SEN 2/CIRC P2127 2127EC-1261
APP SEN 2/CIRC P2128 2128EC-1261
APP SENSOR P2138 2138EC-1275
ASCD BRAKE SW P1572 1572 EC-1202 (Models with ICC)
EC-1211
(Models with ASCD)
ASCD SW P1564 1564 EC-1187
(Models with ICC)
EC-1194
(Models with ASCD)
ASCD VHL SPD SEN P1574 1574 EC-1219
(Models with ICC)
EC-1221
(Models with ASCD)
ATF TEMP SEN/CIRC P0710 0710 AT- 1 3 4
BRAKE SW/CIRCUIT P1805 1805EC-1229
CAN COMM CIRCUIT U1000
1000*4EC-819
CAN COMM CIRCUIT U10011001*4EC-819
CKP SEN/CIRCUIT P0335 0335 EC-1030
CLOSED LOOP-B1 P1148 1148 EC-1168
CLOSED LOOP-B2 P1168 1168EC-1168
CMP SEN/CIRC-B1 P0340 0340EC-1037
CONTROL UNIT(CAN) U1010 1010 EC-822