2006 Hyundai Matrix automatic transmission fluid

2
DRIVING YOUR HYUNDAI
11
DC110G2-E o L (Low Gear): With the selector in this position, first gear will be engaged from rest. Noupshift will occur regardless of vehicle speed and throttle opening. The engine may not be started with the selector inthis position. C090I02A-EAT
CAUTION:
o Shift into "R" and "P" only when the vehicle has completelystopped.
o Do not accelerate the engine in reverse or any of the forward
positions with the brakes applied.
o Always apply the footbrake when shifting from "P" or "N", to "R","D", "2" or "L" position.
o Do not use the "P" (Park) position in place of the parking brake. Al-ways set the parking brake, shiftthe transaxle into "P" (Park) and turn off the ignition when you leave the vehicle, even momentarily.Never leave the vehicle unattend- ed whilst the engine is running.
o Check the automatic transaxle fluid level regularly, and add fluid asnecessary. See the maintenance schedule forthe proper fluid recommendation.
!
DC110E1-E o D (Drive): With the selector in this position, first gear will be engaged from rest and thetransmission will automatically upshift to second, third and fourth depending upon the vehicle speed, throttle posi-tion and the position of the overdrive switch. The engine may not be started with the selector in this position. DC110F1-E o 2 (Second Gear): With the selector in this position, first gear will be engaged from rest. Thetransmission will upshift to second gear depending upon the vehicle speed and throttle position. No upshift to third orfourth will occur. The engine may not be started with the selector in this position.
!
CAUTION:
Do not move the selector to the 2 position when the vehicle speed is in excess of 60 m.p.h.
! CAUTION:
Do not move the selector to the "L" position when the vehicle speed is inexcess of 50 m.p.h. C090H01A-EAT NOTE:
o The brake pedal should be de- pressed when shifting from NEU- TRAL to a forward or reverse gear.
o The brake pedal fully depressed in order to move the shift lever fromthe "P" (Park) position to any of the other posi-tions.
o It is always possible to shift from "R", "N", "D", "2", "L" position.

6
OWNER MAINTENANCE
21
SG110D2-E
Transaxle fluid level checking The vehicle must be parked on level ground with the parking brake firmly applied and the engine at normal oper-ating temperature. (Normal operating temperature will only be achieved when the vehicle has been driven for 6 milesor more). HFC5008
Wipe the dipstick, replace it fully and
promptly remove it again. The fluidlevel should be between the upper and lower marks. CAUTION:
The automatic transaxle unit is a precision engineered assembly andcorrect operation is dependant upon the exclusion of dirt and lint from the unit. Therefore, it is imperative that only lint free cloth (eg nylon) is used for wiping the dipstick andthat the area around the dipstick is thoroughly clean prior to level checking or adding fluid.!
C090A01FC-D With the engine idling and the footbrake
applied, the transaxle selector should be moved from the "P" position through to the "L" position and back to the "N" or "P" position.
Open the bonnet and remove the
transaxle dipstick, remembering thatcare must be exercised to preventinjury occurring through contact with hot or rotating parts of the engine.
This means that the engine, radia-tor, exhaust system etc., are very hot so you should exercise greatcare not to burn yourself during this procedure.
Fluid need only be added if the level is at or below the lower mark and mustnever be increased above the higher mark. If additional fluid is required, this should be poured into the transmissionthrough the dipstick tube with the aid of a suitable funnel.

6 OWNER MAINTENANCE
32
G350B01FC-EAT
(Diesel engine)
The fuel system should be bled to remove air as described in the illustra-tion if the fuel supply is exhausted during travel, when the fuel filter is replaced, or if the vehicle is not usedfor a long time.
1. Remove the air cap with pushing the button.
G350A01FC
BLEEDING THE FUEL SYSTEM
POWER STEERING FLUID LEVEL
SG230A1-E
HFC5004
G230A02FC
Petrol engine
Diesel engine
The power steering fluid level should
be checked daily. SG230B1-E
POWER STEERING HOSES
Power steering hoses should be
checked for damage, deterioration and leakage at each service. To check the power steering fluid level,
be sure the ignition is "OFF", thencheck to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings onthe fluid reservoir.
NOTE: Grinding noise from power steering
pump may be heard immediately after the engine is started in ex-tremely cold condition (below -4°F). If the noise stops dur- ing warm up, there is no abnormalfunction in the system. This is due to a power steering fluid character- istic in extremely cold conditions. FLUID RECOMMENDATION
Only automatic transmission fluid
meeting the specification of PSF-3 or Dexron 2 should be used in the power steering system.