6OWNER MAINTENANCE
28HEADLIGHT AIMING ADJUSTMENT
!
1. Loosen the drain plug at the bottom
of the fuel filter.
2. Tighten the drain plug when water no longer comes out.
3. Check to be sure that the warning light illuminates when the ignition key is turned to "ON", and that it goes off when the engine is started.If in doubt, consult your nearest au- thorized HYUNDAI dealer.
NOTE: It is recommended that water accu- mulated in the fuel filter should be removed by an authorized Hyundaidealer. WARNING:
Be sure to carefully wipe away any water drained out in this manner, because the fuel mixed in the watermight be ignited and result in a fire. G290A03A-EAT Before performing aiming adjustment, make sure of the following.
1. Keep all tyres inflated to the correct
pressure.
2. Place the vehicle on level ground
and press the front bumper and rear bumper down several times. Place the vehicle at a distance of 118 in. (3,000 mm) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant,engine oil and fuel, and spare tyre,jack, and tools). Have the driver or equivalent weight placed in driver's seat.
4. Clean the head lights lens and turn on the headlight (low beam).
G300B01A
6
OWNER MAINTENANCE
29
5. Open the bonnet.
6. Draw the vertical line (through the
centre of each headlight beam pat- tern) and the horizontal line (through the centre of each headlight beam pattern) on the aiming screen. And then, draw the horizontal paral- lel line at 1.18 in. (30 mm ) under thehorizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING.
8. Adjust each cut-off line of the low beam to each vertical line with aphillips screwdriver - HORIZONTAL AIMING.
G290A01A
Horizontal Aiming
Vertical Aiming
SPECIFICATIONS: "H" Horizontal centre line of headlightsfrom ground. Petrol Engine : 25.8 in. (656 mm) Diesel Engine : 26.1 in. (664 mm) "W" Distance between each headlightcentre. Petrol Engine / Diesel Engine : 42.4 in. (1,078 mm) "L" Distance between the headlightsand the wall that the lights are tested against. : 118 in. (3,000 mm)
If the vehicle has had front body repairand the headlight assembly has been replaced, the headlight aiming should be checked using an aiming screen asshown in the illustration. Turn on the headlight switch. (Low Beam Position)
1. Adjust headlights so that main axis
of light is parallel to centre line of the body and is aligned with point "P"shown in the illustration.
2. Dotted lines in the illustration show
the centre of headlights.
G290B03A-EAT Adjustment After Headlight As- sembly Replacement
G290B01B
LW
Cut-off line Ground line
"P"
Horizontal line
Vertical line1.18 in.
H H
10
INDEX
5
Steering Wheel Freeplay .................. ........................ 6-22
Steering Wheel Tilt Lever .............. ...........................1-70
Stereo Sound System ............................................... 1-81
Sunroof ...................................................................... 1-60
Sunshade .................................................................. 1-59
Sun Visor .................................................................. 1-70
T Tachometer ............................................................... 1-47
Towing Trailer and caravan towing .................................... 2-19
Vehicle towing or recovery .................................... 3-12
Transaxle
Autom atic ............................................................... 2-10
Automatic transaxle fluid level checking................ 6-16
Manual ..................................................................... 2-8
Manual transaxle lubricant level checking .............6-15
Trip Computer ........................................................... 1-48
Trip Odometer ........................................................... 1-48
Tyre Balancing .................................................................. 8-4
Chains ...................................................................... 8-4
Changing a flat tyre ................................................. 3-7
In the event of a puncture ....................................... 3-7
Information ............................................................... 8-3
Pressures ................................................................. 8-3
Replacement ............................................................ 8-5
Rotation .................................................................... 8-4
Snow tyres ............................................................... 8-3
Spare tyre(wheel) ..................................................... 3-6 V Vehicle Identification Number
..................................... 8-2
Vehicle Specifications ................................................. 9-1
W Warning and Indicator Lights.................................... 1-42
Windscreen Wiper / Washer Switch......................... 1-52
Adjustable intermittent wiper operation ..................1-53
Rear window wiper and washer ............................ 1-54
Windscreen Wiper Blades .......... .............................. 6-14
Winter Motoring ......................................................... 2-17
