2006 Hyundai Accent head replacement

1FEATURES OF YOUR HYUNDAI
12
!
WINDOW GLASS
B050A01A-AAT
To raise or lower the window, turn the window regulator handle clockwise or counterclockwise. WARNING:
When opening or closing the win- dows, make sure your passenger'sarms, hands and body are safely out of the way.
3. Remove the battery cover with a
coin.
4. Remove the old battery from the case and note the polarity. Make sure the polarity of the new batteryis the same (+side facing up), then insert it in the transmitter.
3FDA2015
B070E01MC-AAT Replacing the battery When the transmitter's battery begins to get weak, it may take several pusheson the button to lock or unlock the doors, and the LED will not light. Re- place the battery as soon as possible. Battery type : CR1220 Replacement instructions:
1. Remove the screw with a phillipsscrewdriver.
2. Carefully separate the case with a flat-head screwdriver. OMC025004

1FEATURES OF YOUR HYUNDAI
76DIGITAL CLOCK
B400A01A-AAT There are three control buttons for the digital clock. Their functions are: HOUR - Push "H" to advance the hour
indicated. MIN - Push "M" to advance the minute
indicated.RESET - Push "R" to reset minutes to
":00" to facilitate resetting the clock to the correct time. When this is done: Pressing "R" between 10 : 30 and 11 : 29 changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 12 :29 changes the readout to 12 : 00.CIGARETTE LIGHTER
B420A02A-AAT
For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it allthe way into its socket. When the ele- ment has heated, the lighter will pop out to the "ready" position.Do not hold the cigarette lighter pressed in. This can damage the heating ele- ment and create a fire hazard.If it is necessary to replace the ciga- rette lighter, use only a genuine Hyundai replacement or its approved equivalent. HHR2098A
OMC025098
B360A01Y-GAT Rear Fog Light Switch (If Installed)
To turn on the rear fog lights, push the switch. They will light when the head- light switch is in the second position and the key is in the "ON" position.
B360A01MC
B360A01MC-R
Right-hand Drive Type
Left-hand Drive Type

6 DO-IT-YOURSELF MAINTENANCE
34HEADLIGHT AIMING ADJUSTMENT
5. Open the hood.
6. Draw the vertical line (through the
center of each headlight beam pat-tern) and the horizontal line (throughthe center of each headlight beam pattern) on the aiming screen. And then, draw a horizontal parallel line at 30 mm (1.18 in.) under the horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillipsscrewdriver - VERTICAL AIMING.
8. Adjust each cut-off line of the low
beam to each vertical line with aphillips screwdriver - HORIZONTAL AIMING. G290A01A
Horizontal Aiming
Vertical Aiming
If the vehicle has had front body repair and the headlight assembly has beenreplaced, an headlight aiming should be checked using an aiming screen as shown in the illustration. Turn on theheadlight switch. (Low Beam Position)
1. Adjust headlights so that main axisof light is parallel to center line of the body and is aligned with point "P" shown in the illustration.
2. Dotted lines in the illustration show the center of headlights.
G290B03A-GAT Adjustment After Headlight As- sembly Replacement
G290A03A-GAT Before performing aiming adjustment, make sure of the following.
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground
and press the front bumper and rear bumper down several times. Place the vehicle at a distance of 3,000 mm (118 in.) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant,engine oil and fuel, and spare tire,jack, and tools). Have the driver or equivalent weight placed in driver's seat.
4. Clean the head lights lenses and turn on the headlight (low beam). G290B01B
LW
H
H Cut-off line
Ground line
"P"
Horizontal line
Vertical line30 mm

6
DO-IT-YOURSELF MAINTENANCE
35REPLACEMENT OF LIGHT BULBS
HLC5033
G270A03A-GAT Headlight Bulb
1. Allow the bulb to cool. Wear eye
protection.
2. Open the engine hood.
3. Always grasp the bulb by its plastic
base, avoid touching the glass.
SPECIFICATIONS: "H" Horizontal center line of headlights from ground.Gasoline Engine: 656 mm (25.8 in.) Diesel Engine: 664 mm (26.1 in.) "W" Distance between each headlight center.Gasoline Engine/Diesel Engine : 1,078 mm (42.4 in.) "L" Distance between the headlights and the wall that the lights are testedagainst. : 3,000 mm (118 in.). G260A02A-AAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reachthe light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and watt-age rating. See page 6-41 for the wattage descrip- tions.
CAUTION:
Keep the lamps out of contact with petroleum products, such as oil, gasoline, etc.
!
4. Using a spanner, remove the head-light assembly mounting bolts.

6 DO-IT-YOURSELF MAINTENANCE
36
8. Remove the protective cap from the
replacement bulb and install the new bulb by matching the plastic base with the headlight hole. Reattach the bulb spring and install the dust cover.Reconnect the power cord.
9. Use the protective cap and carton to
dispose of the old bulb.
10.Check for proper headlight aim.
6. Remove the dust cover. HLC5011
HLC5009
HLC5034-1
5. Disconnect the power cord from the bulb base in the back of the head-light. 7. Push the bulb spring to remove the
headlight bulb. HLC5010
G270A03O

1FEATURES OF YOUR HYUNDAI
12
!
WINDOW GLASS
B050A01A-AAT
To raise or lower the window, turn the window regulator handle clockwise or counterclockwise. WARNING:
When opening or closing the win- dows, make sure your passenger'sarms, hands and body are safely out of the way.
3. Remove four screws back side of the
built-in circuit.
4. Remove the old battery from the case and note the polarity. Make sure the polarity of the new batteryis the same (+side facing up), then insert it in the transmitter. HTB054
HTB055
B050A01A
B070E01TB-AAT Replacing the battery When the transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock thedoors, and the LED will not light. Re- place the battery as soon as possible. Battery type : CR1220 Replacement instructions:
1. Remove the screw with a phillips screwdriver.
2. Carefully separate the case with a flat-head screwdriver as shown in the illustration. HTB053

11
1
CONTROLS AND EQUIPMENT
POWER WINDOWS
B060A01E-AAT
The power windows operate when the ignition key is in the "ON" position. The main switches are located on the driver's armrest and control the front and rearwindows on both sides of the vehicle. The windows may be opened by de- pressing the appropriate window switchand closed by pulling up the switch. To open the window on the driver's side, press the switch(1) down. The windowmoves as long as the switch is oper- ated.
3. Remove four screws back side of the
built-in circuit. HTB054
HTB055
Battery HLC2009-D
(1)
(1)4/5 Door
3 Door
4. Remove the old battery from the case and note the polarity. Make sure the polarity of the new battery is the same (+side facing up), then insert it in the transmitter.
B070E01TB-AAT Replacing the battery When the transmitter's battery begins to get weak, it may take several pusheson the button to lock or unlock the doors, and the LED will not light. Re- place the battery as soon as possible. Battery type : CR1220 Replacement instructions:
1. Remove the screw with a phillips
screwdriver.
2. Separate the case with a flat-head
screwdriver as shown in the illustra- tion. HTB053

6OWNER MAINTENANCE
12SPARKING PLUG REPLACEMENT
G060A01L Prior to installing a sparking plug, the gap between the centre and outer elec- trodes must be checked and adjusted as necessary.Adjustment is facilitated by bending the outer electrode towards or away from the centre electrode. Under no circum-stances should attempts be made to adjust the position of the centre elec- trode.
4. Insert the sparking plug into the cyl-
inder head and using a suitable plug socket, slowly rotate the sparkingplug, (being careful not to cross- thread), until the plug contacts the seating area. Tighten the plug withthe plug socket by a further 1/2 to 3/ 4 of a turn only.
3. Clean around the base of the plug to
be removed, and install the plugsocket ensuring that the ceramic insulator does not become damaged.Turn the socket counterclockwise to remove the plug.
CAUTION:
Sparking plugs must only be cleaned using purpose designed equipment.Wire brushing may damage the cen- tre electrode insulator causing mis- firing to occur. Only the correct gradeof sparking plug should be used. Use of an incorrect grade may result in serious engine damage.
!
SG060A1-E (Petrol Engine Only) This operation should only be performed when the engine is cold.
1. Remove the centre cover from the
engine rocker cover (DOHC Engine only).
2. Remove plug lead from the sparking
plug to be replaced, pulling the leadby the rubber cap. (Pulling the lead may damage the carbon conductor.) 0.039~0.043 in. (1.0 ~ 1.1 mm )
G060C01A
HLC5023