2006 HUMMER H2 flat tire

Or, turn the wheel wrench with the wheel wrench
extender (jack B) counterclockwise to loosen
the wheel nuts.
6. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
7. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire.
Removing the Flat Tire and
Installing the Spare Tire (SUT
and SUV)
Jack A (SUV and SUT)
1. To remove the center
cap, place the at end
of the wheel wrench
in the slot on the wheel
and carefully pry the
center cap out.
Jack B Tools
5-83

2. Slide the ratchet onto the wheel wrench with the
DOWN mark facing you.
3. Turn the ratchet counterclockwise to loosen the
wheel nuts. Do not remove them yet.
You will now need to jack the vehicle up using the
following instructions.4. Assemble the jack and tools as follows:
Front Flat Tire:Attach the jack handle with the
hook end connected to the u-hook/clevis on
the jack. Slide the ratchet onto the jack handle with
the UP mark facing you.
Rear Flat Tire:Assemble the jack together with the
jack handle and the jack handle extension. Press
with the UP mark facing you. The retention clip
on the jack handle extension (arrow) so it engages
into the jack handle. Slide the ratchet onto the
jack handle extension.
5. Turn the ratchet clockwise to raise the jack head to
the lifting point.
5-84

6.Front Flat Tire:
Position the jack under
the vehicle on the
frame behind the at
tire where the
frame sections overlap.
See the following
graphic for an
approximate
measurement of the
jack location on
the frame.
Front Flat Tire – Jack A
X = 28.5 inches (72.0 cm)
5-85

Rear Flat Tire:Place the
jack under the curved rear
axle pad. Make sure
the jack head is positioned
so that the rear axle
pad is resting securely on
the jack head.
{CAUTION:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.
{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to t the
jack lift head into the proper location before
raising the vehicle.
7. Turn the ratchet clockwise to raise the vehicle. Raise
the vehicle far enough off the ground so there is
enough room for the spare tire to clear the ground.
8. Remove all the wheel
nuts and take off the
at tire. Rear Flat Tire – Jack A
5-86

4. Assemble the jack and tools as follows:
Front Flat Tire:Attach the jack handle with the
hook end connected to the u-hook/clevis on
the jack. Slide the wheel wrench onto the jack
handle extension.Rear Flat Tire:Assemble the jack together with the
jack handle and the jack handle extensions.
Press the retention clip on the jack handle extension
(arrow) so it engages into the jack handle. Slide
the wheel wrench onto the jack handle extension.
5. Turn the wheel wrench clockwise to raise the jack
head to the lifting point.
5-91

6.Front Flat Tire:Position the jack under the vehicle
on the front lower control arm behind the at tire.
See the following graphic for an approximate
measurement of the jack location on the frame.Front Flat Tire – Jack B
X = 28.5 inches (72.0 cm)
5-92

Rear Flat Tire:Place the jack under the curved
rear axle pad. Make sure the jack head is positioned
so that the rear axle pad is resting securely on
the jack head.
{CAUTION:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.
{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to t the
jack lift head into the proper location before
raising the vehicle.
7. Turn the wheel wrench clockwise to raise the
vehicle. Raise the vehicle far enough off the ground
so there is enough room for the spare tire to
clear the ground.
8. Remove all the wheel
nuts and take off the
at tire. Rear Flat Tire – Jack B
5-93

14. Tighten the nuts rmly
in a crisscross
sequence as shown by
turning the wheel
wrench with the wheel
wrench extender
clockwise.
15. When you install the wheel and tire, you must also
reinstall the center cap. Place the cap on the wheel
and tap it into place until it sits ush with the wheel.
Storing a Flat or Spare Tire and
Tools (SUT)
Storing the Flat or Spare Tire (SUT)
Use the following art and text to help you store the
spare or at tire back into its proper location when you
are done.To store the at or spare tire on the tire carrier, do the
following:
1. Close the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-14for tire carrier operation.
2. Place the at or spare tire onto the tire carrier with
the outside of the wheel facing you.
3. Reinstall the three nuts holding spare or at tire to
the tire carrier. Tighten the nuts by hand.
4. Use the ratchet and wheel wrench (jack A) to
tighten the nuts rmly.
Jack A Tools
5-96