2006 HUMMER H2 wheel

4. Open the tool bag. You will nd the following
tools needed to remove the spare tire and change
a at tire:
A. Jack Handle
B. Jack Handle Extension (Used for Rear Flats Only)
C. Wheel Wrench
D. Ratchet
Before proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown.Removing Jack B and Tools (SUT)
To remove the cover, unlock it and then pull the
cover off.
Remove the tool kit/rst aid kit to gain access to the tire
changing equipment. Jack A Tools
5-73

3. Open the tool bag. You will nd the following tools
needed to remove the spare tire and at tire:
A. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel BlocksBefore proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown.
To use a wheel block, lift
the wheel block as shown
to lock it into place.
Jack B Tools
5-75

Removing the Spare Tire (SUT)
The spare tire is attached to the tire carrier. To remove
the spare tire, do the following:
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-14for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier.3. Pull off the license plate holder from the spare tire.
4. For jack A, slide the ratchet onto the wheel
wrench with the DOWN mark facing you. For jack B,
attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.
5-76

5. Turn the ratchet counterclockwise to loosen the
wheel nuts.Or, turn the wheel wrench with the wheel wrench
extender (jack B) counterclockwise to loosen
the wheel nuts.
6. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
7. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire. Jack A Tools
Jack B Tools
5-77

4. Open the tool bag. You will nd the following tools
needed to remove the spare tire and at tire:
A. Jack Handle
B. Jack Handle
Extension (2)
(Used for Rear
Flats Only)C. Wheel Wrench
D. RatchetA. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel Blocks
Jack A Tools
Jack B Tools
5-80

Before proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown. To use
the wheel blocks, do the following:
For jack A, locate the wheel blocks which are stored
behind the jack on the driver’s side of the vehicle.
For jack B, remove the
wheel blocks from the tool
bag. Then, lift the wheel
block as shown to
lock it into place.Removing the Spare Tire (SUV)
The spare tire is attached to the tire carrier. To remove
the spare tire, do the following:
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-14for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier. Jack B Wheel Blocks
5-81

3. Pull off the license plate holder from the spare tire.
4. For jack A, slide the ratchet onto the wheel
wrench with the DOWN mark facing you. For jack B,
attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.5. Turn the ratchet with the wheel wrench (jack A)
counterclockwise to loosen the wheel nuts.
Jack A Tools
5-82

Or, turn the wheel wrench with the wheel wrench
extender (jack B) counterclockwise to loosen
the wheel nuts.
6. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
7. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire.
Removing the Flat Tire and
Installing the Spare Tire (SUT
and SUV)
Jack A (SUV and SUT)
1. To remove the center
cap, place the at end
of the wheel wrench
in the slot on the wheel
and carefully pry the
center cap out.
Jack B Tools
5-83