2006 HONDA ACCORD HYBRID AUX

To load or play CDs, the ignition
switch must be in the ACCESSORY
(I) or the ON(II) position.To listen to satellite radio when a CD
is playing, press the CD/AUX XM
button.
You operate the CD changer with
the same controls used f or the radio.
To select the CD changer, press the
CD button. The numbers of the disc
andtruckplayingareshowninthe
display. On vehicles with navigation
system, these numbers also appear
in the upper display. The system will
continuously play a disc until you
change modes. To play the radio when a CD is
playing, press the AM/FM button.
Press the CD button again to switch
back to the CD player.
To play a tape when a CD is playing,
insert a tape in the player (optional).
If a tape is in the player, press the
CD/AUX button. Press the CD/AUX
button again to switch back to the
CD player.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f .
For vehicles with Satellite RadioTo Play a CD
Playing a CD, CD Changer
120
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
——y

y
('
y
y

To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display.
When you press the eject button, the
system switches to the previous
mode (AM/FM radio, satellite radio
(U.S. models), or tape player
(optional f or U.S. models)).
To remove a dif f erent disc f rom the
changer,firstselectitwiththe
appropriate preset bar or icon. When
that CD begins playing, press the
eject button. Continue pressing the
EJECT button to remove all the discs
f rom the changer.
To remove all the discs in the
changer in a sequence, press and
hold the eject button for about 2
seconds.
To play a tape when a CD is playing,
insert a tape in the player (optional).
If a tape is in the player, press the
CD/AUX button. Press the CD/AUX
button again to switch back to the
CD player.
If you turn the system of f while a CD
is playing, the CD will stay in the
drive. When you turn the system
back on, the CD will begin playing
where it lef t of f .
Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD button.
PresstheAM/FMorCD/AUX
(XM)buttontoswitchtotheradioor
satellite radio while a CD is playing.
To play the CD, press the CD button
again.
Playing a CD, CD Changer
Removing CDs f rom the Changer
To Stop Playing a CD
124
——y

y
('
y
y

Playing a T ape (U.S. Vehicles)
Features
127
PWR/VOL KNOBUPPER
DISPLAY
AUDIO
DISPLAY
BUTTON
SEEK BAR
CD/AUX
BUTTON
SEEK BAR RPT INDICATOR TAPE DIRECTION
INDICATOR
RPT
BUTTON
PWR/VOL
KNOBRPT INDICATOR TAPE DIRECTION INDICATOR
CH/DISC
BAR
PRESET BARS
Without Navigation System With Navigation System
(U.S. model shown) (U.S. model shown)
REPEAT
ICONTAPE
DIRECTION
ICONS
NR ICON
CD/AUX XM
BUTTON
——y

y
('
y
y

Î
Î
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Make sure the open side of the tape
is facing right, then insert the tape
most of the way into the slot. The
system will pull the tape in the rest
of the way, and begin to play it.Dolby noise reduction turns on
when you insert a tape. The
indicator will light in the
display. If the tape was not recorded
in Dolby, turn it of f by pressing the
Preset 4 (NR) side of the preset bar
or touching the NR icon. Dolby
remains of f until you press the
preset bar or the icon again.
The tape direction indicator will
show you which side of the tape is
playing. If you want to play the other
side, press the Preset 3 (PLAY/
PROG) side of the preset bar, or
press the AUDIO DISPLAY button
and then touch the appropriate tape
direction icon. When the player
reaches the end of the tape, it will
automatically reverse direction and
play the other side. To remove the tape, press the eject
button. If you want to turn the player
of f , press the PWR/VOL knob or
turn off the ignition. The tape will
remain in the drive. When you turn
the system back on, the tape will
begin playing where it lef t of f .
To switch to the AM/FM radio,
Satellite Radio, or CD changer while
a tape is playing, press the AM/FM
or CD/AUX (XM) button. To change
back to the tape player, push the
CD/AUX (XM) button.
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing
Corporation. ‘‘DOLBY’’ and the double-D
symbol are trademarks of Dolby
Laboratories Licensing Corporation.
Optional on all U.S. models
To Play a Tape To Stop Playing a Tape
Playing a T ape (U.S. Vehicles)
128
——y


y
('
y

y

µµ
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position.
Turn the system on:
Turn the PWR/VOL knob to adjust
the volume. Push any of the f ollowing: PWR/
VOL knob or the CD/AUX XM
button. Push any of the f ollowing: PWR/
VOL knob, the CD/AUX XM, or
AUDIO button. When in the satellite radio mode,
you can use any of three methods to
f ind channels: TUNE, SEEK/SKIP
(CATEGORY), and SCAN.
Turn the TUNE knob to change
channels. Turn the knob right f or
higher numbered channels and lef t
f or lower numbered channels.
Press the TUNE bar to change
channel selections. Press f or
higher numbered channels and
f or lower numbered channels. The
seek/skip f unction selects the
various categories in XM, such as
Jazz/Blues, Rock, Classical, etc.
Push the to change the
category f orward. Push the to
change the category backward. To
search f or channels within a
category, turn the TUNE knob
clockwise or press the TUNE bar .
For vehicles without Navigation System
For vehicles with Navigation System
For vehicles with Navigation System
For vehicles without Navigation System
To Play XM Satellite Radio To Select a Channel TUNESEEK /SK IP (CA T EGORY)
Playing the XM Satellite Radio
132
TM
TM
——y


y
('
y
y

µµOnce your XM channels are preset,
pressing the CH DISC button will
select your preset channels.
The scan f unction samples
all channels f or 5 seconds. To
activate the f unction, push the SCAN
button. Push it again to get out of the
sequence. Each preset icon or button
canstoreonechannelinXM1and
one in XM2. Push the CD/AUX XM button.
(You will see XM1 or XM2.)
Use the TUNE, SEEK or SCAN
function to tune the radio to a
desired channel.
Pick a preset icon or button and
hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on XM1 and XM2.
1.
2.
3.
4.For vehicles with Navigation System
Playing the XM Satellite Radio
SCA N
Preset
Features
133
TM
——y


y
('
y
y

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Drivingonaneast/westroadwith
a mountain on the south side of
the road.
There may be other geographic
situations that could af f ect satellite
radio reception. Driving on a single lane road
alongside dense trees taller than
50 ft. (15 m) to the south of you. Driving on the lower level of a
multi-tiered road. Driving on a road beside a vertical
wall, steep clif f , or hill to the south
of you. Driving in tunnels.
Driving on the north side of a
large commercial truck on an
east/west road. If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or ON (II) position, push the
PWR/VOL knob to turn on the audio
system and press the CD/AUX XM
button. A variety of music types and
styles will play.As required by the FCC:
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.Receiving Satellite Radio Service
Playing the XM Satellite Radio
Features
135
TM
——y


y
('
y
y