2006 GREAT WALL SO COOL window

B0-11Vehicle Body
Rear Door
Rear Door (
)
Element Figure
glass
glass channel
Outer auchi
glass bracket and
glass gasket
door limiting
device door hinge
electric switch
door lampinner cliplower rear glass
guide track
small
sliding
track door lock assemblyn
lock clipoutdoor handle
upper glass guide track
indoor handlelock ring quarter window glass
sliding
channel
SF

B0-12Vehicle Body
Rear Door
Rear door(
)
Element figure
glass
glass channel
outer auchi
door limiting devicedoor hinge
electric switch inner clipdoor lock assembly
lock clip
outdoor handlelock ring quarter
window glass
screw cap
glass supporter
indoor handle
SJ

B0-15Vehicle Body
Rear Door
SF
SJ4. Tear down the outer auchi
Prize the clipes alongside the edge of paneling to tear down the
outer
5. Tear down the door window glass;(Dr SF SL SK SY SJ)
Tear down the fixing bolts of two glass channels
(a) Pull the glass up to take it down.
(b) Pull the glass downwardly to take it down after disassem-
bling the tail door lower baffle and lower dust strip (Dr)
6. Tear down the upper glass guide track (SF)
Tear down the bolts and guide track.
7. Tear down the lower rear glass guide track (Dr SF);
Tear down the bolts and guide track.
8. Tear down the quarter window glass (SF SJ)
9. Tear down the door glass channel
10. Tear down the glass elevator(Dr SF SL SK SY)
(a) Tear down the two fixing bolts of small sliding track.
(b) Tear down the fixing bolts of three elevators (manually
operated)
(c) Disassemble the elevator through auxiliary hole.

B0-16
(SJ)
(a) Tear down the four fixing bolts of elevator bracket;
(b) Tear down fixing bolts of three elevators;
(c) Disassemble the elevator through the auxiliary hole. Vehicle Body
Rear Door
11. Tear down the lock ring inside the vehicle;
Disconnect the connecting bar to tear down the lock ring inside
vehicle body.
12. Tear down door lock and the outdoor handle with lock
barrel:
(a) Disconnect the outdoor with lock barrel from the con-
necting bar.
(b) Tear down three screws and door lock.
(c) Tear down the two bolts and the outdoor handle with lock
barrel.
(d) Tear down the spring snapping ring and lock barrel.
Change of Glass
(Dr SF)
1. Tear down the glass bracket with screwdriver or similar
tool.
2. Coat the black glue on the inner side of glass bracket
liner.
3. Tap the glass bracket with rubber hammer to encase it.
Tear down the bolts on gear panel with the pliers or similar
tool.
4. Tear down the bolts of door window glass bracket to take the
glass out.
SJ
a
Dr
a:35mm
bb:80mm(manual)
65mm(electric)
SF

B0-18
10. Adjust the door window glass Vehicle Body
Rear Door
Adjust the balance arm upwardly or downwardly until the
dimensions A and B shown in the drawing are equal, and then
fix the balance arm.
11. Mount the outerauchi
8. Mount lower rear glass guide track (Dr SF)
Mount the bolts and guide track.
9. Mount the door window glass;
(Dr SF SL SK SY SJ)
Put the glass in the door cavity and then fix the glass on the
glass elevator with two bolts.
Mount on the tailgate baffle and lower dust strip (Dr) 5. Mount the door glass channel;
6. Mount on the quarter window glass (SF SJ)
7. Mount the upper glass guide track (SF)
Mount the bolts and guide track.
12. Mount the door interior trim panel;
13. Mount the indoor handle:
(a) Push the indoor handle in the door paneling and slide it
backwardly.
(b) Tighten the screws.
ABA=B
SF
SJ

B0-19
14. Mount the elevator handle (Dr)
Mount the paneling and elevator handle with spring snapping
ring as shown in the drawing under the condition that the all
of doors and windows of vehicle are closed. Vehicle Body
Rear Door
forward30

B0-37
side-window glass
Side-window glass (
)
Element mounting position
SF
Vehicle Body
Side-Window Glass
SY
side-window glass
spilling strip
trim strip of side window

B0-38
Side window glass (
)
Element mounting position
Vehicle Body
Side-Window Glass
SJ
side-window glass
spilling strip
trim strip of side
window
Dismantle of side window glass
1. Tear down the following parts:
(a) Lower trim panel of rear column;
(b) Rear side-panel trim
(c) Roof
2. Tear down the side window glass
(a) Tear down the three hex nuts and eight nuts on flange
(SF)
(b) Cut a small open in the sealing glue between the glass and
body with knife, then insert the steel wire into the small
open and pull it fro and to slowly until the sealing glue
between the glass and body separate completely, and pull
the glass out to take it down.
Notice: be careful not damage the body and glass.
Mount of side window glass
1. Clean the body and glass;
Clean the contacting face of body and glass completely with
cleaning materials.
2. Cleaning the sealing strip;
Clean the sealing strip surface with cleaning materials.