2006 GREAT WALL SO COOL mirror

BE-79
SF
1 connected to protective box I
2 connected to protective box I
3 rear vision mirror
4 front door-lamp switch
5 rocker switch
6 rocker at front door Wire harness distribution at front left door, front right door, rear left door and rear right door are same with each other.
1 2345
6
7 891011
wire harness at front doorwire harness at rear door
Wire harness of four doors(continued)
Body Electric System
Wire Harness Distribution
7 lock-out device at front door
8 wire harness at central part
9 wire harness at central part
10 rocker at rear door
11 rocker switch

B0-4Vehicle Body
Front Door
Front door
Element figure
(glass)
glasschannel
outer auchi
inner tri-angle trim panel
door limiting device
door hinge
indoor handle
seal strip on
door plate
electric switch
and panel
interior trim panel
of electric door
(Dr)
interior trim panel
of electric door
(SF) interior trim panel of
electric door
sleeve
snapping ring elevator handle
(SL SK SY SJ)
door lamp
inner clip
lower rear glass
guide track sliding channelsmall sliding track door lock assembly
lower front glass
guide track lock cliplock ringlock barreloutdoor handle
manual interior
trim panel(Dr) snapping ring
glass bracket and glass gasket
rear vision mirror

B0-5
Adjustment of front door
1. Adjust the car door in the front-back and vertical direction;
Adjust the car door under the condition that the bolts of body
side hinge are loosened.
2. Adjust the car door in left-right and vertical direction
Adjustment should be made after the bolts of side hinge of
body are loosened.
3. Adjust the clip of door lock:
(a) Check whether the car door assembly and the match of
door lock are adjusted correctly.
(b) Loosen the lock clip lightly to mount the screws and tap
the lock clip with hammer to adjust their positions.
(c) Screw off the fixing screws of lock clip.
Disassembly of front door
1. Tear down the elevator handle (Dr)
Pull out the snapping ring of spring with dishcloth and tear
down the elevator handle and the sleeve.
2. Tear down the indoor handle
3. Tear down the inner triangle trim panel;
Loosen the clip open with a screwdriver to tear down the inner
triangle trim panel.
Notice: before using the screwdriver, wrapping the
screwdriver head with adhesive strap.
4. Tear down the rear vision mirror;
Tear down the three screws and rear vision mirror. Vehicle Body
Front Door

B0-9
manual indoor plate
Electric indoor plate (Type A)
ten clips
12 clips
Vehicle Body
Front Door
12. Mount the interior trim panel of car door:

Dr)
(a) Connect the handle to the control lever first, then pull it
out from the indoor handle hole.
(b) Fix the clip by tapping to encase the interior trim plate of
car door in the corresponding hole of car door interior
panel.
(c) Use one screw to mount the inner clip.

Dr SF)
(a) Connect the handle to the control lever first, and then pull
it out from the indoor handle hole.
(b) Fix the clip by tapping to encase the interior trim panel in
the corresponding hole of car door interior panel
(c) Mount the inner clip with one screw; and
(d) Mount the electric switch and panel.

SL SK SY SJ)
(a) Connect the handle with the control lever first, then pull
out it from the indoor panel handle.
(b) Connect the plugging elements.
(c) Fix the clip by light tapping to encase the interior trim panel
of car door in the corresponding holes on indoor panel.
(d) Mount the inner clip with two bolts;
(e) Mount the four screws to fasten the interior trim panel of
car door, and cover the nuts.
(f) Mount the electric elevator switch.
13. Mount the indoor handle:
(a) Push the indoor handle into the car door paneling and
make it slide backward.
(b) Screw on the screws;
14. Mount the elevator handle (Dr)
Mount the paneling and elevator handle with spring snapping
ring under the condition the car doors and windows are closed
completely as shown in drawing.
12 clips
9. Adjust the car door and window glass;
Adjust the balance arm upwardly or downwardly until the
dimensions of A and B shown in drawing are equal, and then
fix the balance arm.
10. Mount the outer
Encase the claw of clip into the paneling seam and press the
outer on the paneling.
11. Mount the rear vision mirror
inner panel of electric door (type B)
four sets of bolt and nut
front