2006 GREAT WALL SAILOR Engine idle up

SR-14Steering System
Power Steering (On-Vehicle Inspection)
Change of power steering liquid
1. Tear down the oil-returning hose from the oil cup to
drain the liquid into the container;
2. Run the engine in the idle status, and rotate the
steering wheel toward the max rotating angle for
several times in right or left direction while draining the
liquid, until the oil in steering liquid is drained up.
3. Turn off the engine.
4. Connect the oil-returning pipe and inject the new
power steering liquid in the liquid tank;
Hydraulic oil type: No.8 Liquid drive oil (Q/SH003.01.012-88)
5. Start the engine, and make it running in the idle status.
Rotate the steering wheel to the max rotating angle repeatedly
several times, meanwhile, supplement new power steering
liquid in the liquid tank until there is no foam or turbidities in
the liquid tank, and the oil indicating lamp reaches the marked
range when the engine is turned off.
6. Tighten the liquid tank cover
7. Exhaust the air in the power steering system;
Ai-r bleeding in power steering system
1. Check the liquid level height in the liquid tank
Check the liquid level and, if needed, supplement the liquid.
2. Start the engine in the idle status and rotate the
steering wheel repeatedly to the max rotating angle
several times.
3. Turn off the engine and connect the ethane pipe and
bleeding plug.
4. Start the engine and rotate the steering wheel
repeatedly to the max rotating angle several times.
5. Locate the steering wheel at the intermediate position.

AC-13Air-Conditioning System
Compressor
Disassemble of compressor
1. Run the engine in the idle status for ten minutes under
the air-conditioning situation;
2. Turn off the engine;
3. Disconnect the cathode lead from the storage cell;
4. Disconnect the electromagnetic clutch lead from the
matching wire;
5. Exhaust the refrigerant from the refrigeration system;
6. Disconnect the two hoses from the auxiliary valve of
compressor;
Cover the opening joint with cork right away to prevent the wet
gas entering in to the system.
7. Tear down the compressor:
(a) Tear down the fan cover;
(b) Loosen the driving belt;
(c) Tear down the fixing bolts of compressor bracket and the
compressor.
Mount of compressor
1. Mount the compressor with fixing bolts;
Tightening moment
(25-30)N
m
2. Mount the driving belt correctly;
Requirement for belt tension: the tension belt is allowed
to reduce (9-13)mm under 98N after the compressor
runs for five minutes;
3. Connect the two hoses to the auxiliary valve of
compressor;
Tightening moment
(see page AC-8)
4. Connect the clutch lead to the matching wire;
5. Connect the cathode lead of storage cell to the storage
cell, and
6. Vacuumize the system and inflate the refrigerant:
Vacuum time:
Dr SL SK SF SJ
Vacuumize for 20min and main-
tain the pressure for 30min;
SY
Vacuumize for 30min and maintain for 30min
Inflated refrigerant quantity:
Dr
(600-650)g
SL
700
0g
SK SJ
560
0g
SF
(700-720)g
SY
850
0gcorrect incorrect incorrect
98N

A-3
Fastening location N*m
Upper tooth(JK72TWD)
Fastening location N*m
Specification of Maintenance and Up-Keeping
Transfer Box
Maintenance and Up-keeping of Transfer Box
1. The oil level of transfer box should be checked when exchanging the engine lubricant or the vehicle
covers more than 8000 km
and add the lubricant where necessary.
2. Change with the appointed lubricant each year or after the vehicle covers more than 48000 km.
Notice: lubricant brand: 85W/90 GL-5.
Fastening torque of relative connecting elements
15
20
10
15
12
17
15
20
15
20
15
20
15
20
30
40
60
70
30
40
30
40
17
22
30
50
20
40
30
40
90
125 Toggle fork at first, second and fifth gears and the screw of
toggle fork
Bolt on odometer pressure plate
Screw on baffle of rear bearing of output shaft
Screw on baffle of reverse idler shaft
Locating screw of gearshift yoke block
Bolt of front cover
Bolt of gearshift cover
Pillar of clutch toggle fork
Bolt of clutch cover
Bolt of rear body (M10X1.25X130)
Bolt of rear body (M10X1.25X80)
Plug of locating spring
Oil filling/draining plug
Reverse gear switch assembly
Location mechanism cluster
Locking nut at rear end of countershaft
Fastening location N*m
Flange nut
Oil drain plug
Bolt of motor clip
Fixing bolt of motor
Clutch coil nut
Housing bolt
Oil pump bolt
Venting valve
Bolt of front connecting body203
244
19
30
8
11
8
11
8
11
27
46
4.0
8.5
8
19
27
46 Oil filling/draining plug
Location mechanism cluster
Pillar of clutch toggle fork
Bolt on odometer pressure plate
Reverse gear switch assembly30
50
30
50
30
50
10
15
30
50