2006 GREAT WALL SAILOR Gear box

MT-45
sealed material
Gearbox
Assembly of Gearbox
20. Mount the stop ring of the front bearing
(a) Mount the two stop rings in the input shaft bearing and
countershaft front bearing with the split-ring-type pliers.
(b) Mount the coated component elements of front cover.
(c) Coat the sealing agent on the bolt thread, and
(d) Mount and propel tightly the bolts.
Tightening moment
(15
20)N
m
21. Mount the rear body, gear-change bar and selection bar
and their housings
(a) Coat the sealing materials on the rear body as shown in
the drawing.
(b) Mount the gearshift shaft and gearshift yoke block in the
rear body.
(c) Mount the gearshift catching head in the groove of guide
block, and
(d) Mount the catching head with the rear body together.
(e) Mount and propel tightly the bolts.
Tightening moment

Shang chi
(30
40)N
m
Tang chi
(30
45)N
m

MT-46
4WD
Gearbox
Assembly of Gearbox
(f) Fasten the rear cover bolts of the four-gear driving
gearbox
Tightening moment:(30
45)N
m(Tang tooth)
(g) Mount and propel tightly the setting bolts of the gearshift
yoke block.
Tightening moment
(17
22)N
m
22. Mount the steel ball spring and plug
(a) Coat the sealing agent on the plug thread.
(b) Mount the steel ball, setting spring and setting spring
plug.
Tightening moment
(17
22)N
m
23. Check the following items after mounting the rear body
or gearbox
(a) Check the stability of the running input shaft and output
shaft.
(b) Check the gearshift stability of each speed
24. Mount the component elements of the locating mecha-
nism
(a) Mount the black component elements of the locating
mechanism on the side of the five-speed reverse gear.
(b) Mount another component element of locating mecha-
nism and propel it tightly.
Tightening moment
(30
40)N
m
25. Mount the gearshift cover of the gearbox.
(a) Mount the gearshift cover coated with sealing agent.
(b) Mount six bolts and then tighten them.
Tightening moment
(15
20)N
m

MT-47Gearbox
Assembly of Gearbox
26. Mount the clutch frame
(a) Mount the clutch frame.
(b) Coat the sealing agent on the bolt thread.
(c) Mount the nine bolts and then tighten them.
Tightening moment

Upper tooth
(60
70)N
m
Tang tooth
(30
45)N
m
27. Mount the back-up lamp switch.
Tightening moment
(20
40)N
m
28. Mount the driven gear of odometer
(a) Mount the driven gear of odometer.
(b) Mount the bolts and tighten them.
Tightening moment
(10
15)N
m

TF-1
page
Notice ........................................................................... TF-2
Troubleshooting ........................................................... TF-3
Product Description and Simple Maintenance ............. TF-5
Dismantle and Mount of Transfer Box .......................... TF-7
Disassembly of Transfer Box ....................................... TF-9
Assembly of Transfer Box ............................................ TF-14
Washing, Inspection, Maintenance and Change .......... TF-24
Washing ................................................................... TF-24
Inspection ................................................................ TF-25
Maintenance and Change of Gear and Chain gear .. TF-28
Attachment for Inspection, Maintenance and
Change of Parts ....................................................... TF-30
Transfer Box
TF

TF-3Transfer Box
Troubleshooting
Common troubles Causes Resolving approaches
Change the lubricant or supplement the
lubricant volume.
Guarantee the torque of all connecting
elements stand at the specified value.
Open the transfer case to check the
bearing and othe parts whether is weared
or daamaged,if this happened,change
the parts.
Difficulty in mechanic gearshift or
outplace gear engagement
Troubleshooting
Incorrect lubricant or insufficient
lubricant volume.
Looseness of connecting bolt or other
connecting element.
Noise from the transfer box bearing Noise, which is spreader by the transfer
box instead of clutch, engine, drive shaft
and other parts, occurs in each speed. No driving of front wheel in the four-
gear engagementDrive chain breakDisassemble and check the damage of
inner parts, and change the chain. Adjust or repair shift lever.Open the
transfer box to check the toggle fork and
guide shaft, and change the parts as
requirement.Open the transfer box to
check whether the parts is wearied or not,
and, if any, change the weary parts.Open
the transfer box to check whether the
parts is wearied or not, and, if any, change
the weary parts.Open the transfer box to
check whether the parts is wearied or not,
and, if any, change the weary parts. Overlarge loose fit clearance of the
shift toggle fork on the shift guide
shaft.
Wear of the shift toggle fork
assembly including pin and contact
roller.
Wear of the shift cam hub and the
liner.
Attainment of coupling gear Mechanic gearshift seizing at a certain
location Engagement failure of the mechanically
shift transfer boxDamage or unsuitable adjustment of
the shifting mechanism.
Damage or serious wear of the inner
shifting parts, or looseness or
attainment of the shift toggle fork
assembly on the guide shaft.
Unsuitable adjustment of shift lever.Adjust or repair the shift lever mechanism.
Change the seriously wearied parts.
Change the loose or weary parts. Refer to the vehicle manual for correct
operation.
Add the specified oil of given volume.
Open the rear cover of transfer box to check
and changer the damaged parts.
Open the rear cover of the transfer box to
check whether the sliding parts can slide
freely along the axle, if not, dismantle it and
change the damaged parts. Incorrect operation.
Lubricant of inferior quality or
insufficient volume.
Adhesive bonding of shift toggle fork.
Adhesive bonding of the sliding joint
cover, locking sleeve or gear. Mechanic gearshift failure under the
movement of shifting handleBreak or damage of the shift rocker
arm or shift lever.
Damage of the guide plate of shifting
cam;Change the damaged element.
Open the rear cover of the transfer box to
check the damaged element and change
it. Electric gearshift troubleDamage or failure of electrically
controlled element, electric module,
speed sensor, electric motor, electric
clutch, or built-in wire harness.
Damage or worn of shifting cam,
joint cover, locking sleeve, toggle
fork or shift guide axle.Adhesive
bonding shiftRefer to the vehicle usage manual to
diagnose the failure element and change
it as requirement.
Dismantle the weary or damaged parts
and change it as requirement.
Dismantle and check the free movement
of sliding element, and change it as
requirement

TF-4Transfer Box
Troubleshooting
Common troubles CausesResolving approaches
Unsuitable tire pressure.
Noise, which is spread by the transfer
box instead of the clutch, engine or other
parts, occurs at each speed.Gear noise.
Damage or wear of chain gear or
chain.Open to check whether there is weary
element or damaged element (including
the odometer gear) and, if any, change
them
Noise occurs in the high-speed or low-
speed four-gear driving.Open to check whether there is wear or
damage, and if any, adjust the tire pressure
to suitable value.
Oil leakage in transfer box. Frame Break of transfer box.
Oil leakage of other element.
Ventilation pipe block
Over-added lubricant or lubricant of
unsuitable brand
Looseness of the bolts on sealing
face.
Sealing glue of different brand or
unused sealing glue.
Oil seal wear or damage.Change the frame.
Check the leakage by wiping dry.
Open and clean it and, if necessary,
change it.
Use the specified lubricant and adjust the
lubricant to suitable volume.
Propel the bolts tightly as requirement.
Use the specified sealing glue and propel
the bolts tightly as required.

TF-5Transfer Box
Product Description and Simple Maintenance
Transfer Assembly NO. of Manufacturer
product assembly NO.
display
termnumber
displaythe last digit of the year
displaythe specific monthly
manufactuer data
displaythe month numnber
Example display:From January (A) to December (L)
Product instruction and simple maintenanceManufactuer data
Product instruction and simple mainte-
nance
1. Product Introduction
The transfer box adapted by our company is the transfer box
of 45-55 manufactured by Bogeguana, which is two-speed
and time driving, a set of planetary mechanism used is to
obtain the speed-reducing performance, while the driving
force is transmitted to the front driving gear by a highly precise
chain. The planetary gear train and rear output shaft element
of transfer box is lubricated initiatively through oil bath and oil
pump. This transfer box has four gears:

2H-stands for the two high gears
in which, only the two
rear wheel are driven, and the gear ratio of the transfer box
is 1:1


4H-stands for the four high gears, in which , all of the four
wheel are driven, and the gear ratio of the transfer box is
1:1


N- neutral location (this location only exists in the transfer
box of manual gearshift )
No driving force is transmitted
to the wheel when the input shaft and output shaft are
disconnected.

4L-stands for low gears, the four wheels are all driven, and
the gear ratio of transfer box is 2.48:1.
The gearshift of the mechanical gearshift transfer box is
obtained through the shifting-cam-type guide plate that is
operated by the shift rocker arm.
Sign board: which is fastened at the obvious external location
of transfer box, and on which the detailed data are marked.
borgwarner

TF-7Transfer Box
Disassembly and Mount of Transfer Box
Disassembly and Mount of Transfer Box
1. Transfer Box Disassembly
(a) Drive the vehicle on the lifting jack.
(b) Locate the gear of transfer box at the neutral
position, shift the transfer box to the 2H and
extinguish the engine.
(c) Disconnect the cell cathode.
(d) Lift the vehicle.
(e) Put down an oil disc under the transfer box, tear
down the oil drain plug and oil filling plug of the
transfer to drain all the lubricant up, then re-
mount the two plugs.
(f) Disconnect all wires and wire harnesses that
connected with the transfer box.
(g) Take apart the hose on the venting valve of
transfer shaft.
(h) Disconnect the linkage of the front drive shaft
with the front flange of the transfer box.
(i) Disconnect the linkage of the rear drive shaft
with the rear flange of the transfer box.
(j) Raise the transfer box up with the jack.Notice: The transfer box shall be guaranteed to
support by the lifting jack before tearing down
the sets of bolt and nut that connected with the
transfer box and gearbox. The transfer box is
not allowed to hang directly on the gearbox
through spline because such operation will
damage the transfer box parts.
(l) Tear down the connecting nuts between the
transfer box and gearbox and take down the
transfer box.
(m) Move the transfer box backward directly until
the linkage between the input shaft of transfer
box and the gearbox spline.
(n) Put down the lifting jack of the transfer box, and
(o) Tear down the gasket between the transfer box
and gearbox. Clean the gasket or glue on the
coupling face of front body of transfer box with
rear body of the gearbox. Take notice not to
damage the coupling face.
1234
5 6 7
8
9
1. input shaft
2. front frame of transfer box
3. rear cover of transfer box
4. flange
5. front output fork flange
6. venting valve
7. gasket
8. rear body of gearbox
9. bolt