2006 GREAT WALL SAILOR wheel

A-2
Clutch
Specification
Item Specification
Fastening torque for clutch tube on master cylinder
Fastening torque for clutch tube on wheel-brake cylinder
Fastening torque for clutch pressure plate160
190-200
5-15
0.3
0.8
0.2
0.6
5
Max misplacement
0.5 Pedal height (calculated from front wall
Pedal free stroke
Min depth of clutch-facing rivet
Max radial swing difference of clutch rib
Max radial swing difference of flywheel
Max width of wear of diaphragm spring
Max width of wear of diaphragm spring
Alignment degree of diaphragm spring endApplicable vehicle model
Dr SF
SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Torsion moment
Fastening location (N*m)
15-17
15-17
30 Applicable Vehicle model
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Dr SF SL SK SY SJ
Gearbox
Three-grade maintenance for gearbox
1. Grade I maintenance for gear box
Grade I maintenance: Check the lubricant level to see whether the lubricant level is in alignment with the lower edge of oil
filler; if the lubricant is lower than the oil filler lower edge, add the lubricant; or the insufficient lubricant will lead to the poor
lubrication or burn-out of bearing and teeth; while the over-high lubricant will cause the overheating and oil leakage.
2. Grade II maintenance for gear box
Grade II maintenance: The gear box of a new vehicle should be maintained by exchanging the lubricant during the
first grade II maintenance and should be washed with kerosene; and the lubricant quality should be checked in the
grade II maintenance in later time, if the lubricant is diluted, gumming or over-dirty, it should be changed.
3. Grade III maintenance
The gearbox should be disassembled for inspection, washing and oil change.
Notice: As the new vehicle is in the running-in status, the gearbox should be maintained by exchanging lubricant
after the vehicle covers 1500 km,
Lubricant Type
GL-5 SAE80W/90
Torsion moment of relative connecting elements
Tung Teeth: Tang tooth(5DYA4TWD
5DYA8FWD)
Unit
ãã Specification of Maintenance and Up-Keeping
Clutch and Gearbox
Locating screw of fork axle at first and second gear
Locating screw of yoke block
Screw on baffle of rear bearing of output shaft
Screw of reverse idler shaft
Bolt of gearshift cover
Bolt of front cover
Bolt of rear body
Bolt of clutch shell
Bolt of locating spring13
17
15
20
17
22
17
20
15
20
15
20
30
45
30
45
17
22 Fastening location N*m

A-4
Drive Shaft
Torsion moment
Fastening location Applicable vehicle model N*m
Connecting bolt
Fixing bolt of central supporter74
5
40
5 Dr SF SL SK SY SJ
Dr SL SK SY SJ
Inflation pressure of tire
Ground clearance of chassis
Steering angle of inner wheel
Kingpin inner inclination
Outer inclination of front wheel
Mechanical steering
Power steering
Kingpin rear inclination (inclination)
Mechanical steering
Power steering
Toe-in
Error in length between left and right
drag rod
Side slip valueFront:220
0kPa
Back:240
0kPa
Front:250
0kPa
Back:250
0kPa
295mm
255
mm
58.5mm(difference in height between
shaft center of lower arm and wheel
center)
310
mm
295
mm
36
40


32

32
34

9
30'
5'
14
52'
0
30'
0'
0
10'
0'
0
20'
0'
0
20'
5'
1
50'
-20'
2
5'
5'
2
0'
0'
0-2mm
=2mm
=5m/km

.5m/km
Suspension System and Automobile Axle
Specification
Item Applicable vehicle model Specification
Dr SL SK SY SJ
SF
Dr
SL SK
SF
SY
SJ
Dr SL SK SY
SF
SJ
Dr SL SK SY
SJ
Dr SL SK SY
Dr
SL SK SY
SJ
Dr SL SK SY
Dr SL SK SY
SJ
Dr SL SK SF SY SJ
Dr SL SK SF SY SJ
Dr SF
SL SK SY SJ
HPM

Specification of Maintenance and Up-Keeping
Drive shaft, Suspension System and Automobile Axle

A-6
Torsion moment
Fastening location Applicable vehicle model N*m
Fixing nut of steering wheel
Connecting nut of steering ger and swing arm
Fixing bolt of steering driven arm
Fixing bolt of steering gear
Connecting nut of steering drag rod and swing arm of
steering gear
Connecting nut of steering drag rod and steering driven
arm
Connecting nut of steering drag rod and front brake
Steering limit boltDr SF
SL SK SY SJ
Dr SF
Dr
SF
SL SK SY
SJ
Dr
SF
SL SK SY
SJ
Dr SF
Dr
SF
Dr SF
SJ50
5
30
2
245
25
80
10
142
10
83
10
78
10
96
10
145
10
96
10
78
10
91
10
91
10
59
5
91
10
90
10
Steering system
Specification
Item Applicable vehicle model Specification
Max play of steering wheel
Tension degree of driving belt:
When f=98N New belt
Old beltDr SF
Dr SL SK SF SY SJ
Dr SL SK SF SY SJ6

5-7mm
7-9mm
Specification of Maintenance and Up-Keeping
Steering System

B-2
Disassembling and as-
sembling tools for lock-
ing nut of steering
knuckle3916001



Press fitting tool for in-
ner bearing of front wheel
hub3916002
3916003
3916004
3916005
3916006
3916007
3916008
3916009
3916010 Press fitting tool for outer
bearing of front wheel
hub
Disassembling tool of
ball stud
Fixing tool of main teeth
flange of needle bearing
Press fitting tool for steer-
ing knuckle oil seal
Disassembling tool of
shorter liner of lower arm
Mounting tool of shorter
liner of lower arm
Mounting and disassem-
bling tool of long liner of
lower arm
Disassembling tool of
upper arm liner

























SST Special Service tool
Diagram Tool name tool number Remark
SST Special Tool
Special Service Tool
Application position
Front axle
Rear axle
2WD 4WD

B-3
Application position
Front axle
Rear axle
2WD 4WD
3916011

3916012
3916013
3916014
3916015
3916016
3916017
3916018
3916019
3916020 Press fitting tool of up-
per arm liner
Disassembling and as-
sembling tools of wheel
brake cylinder of front
brake caliper
Disassembling tool of
front drive shaft bearing
Pneumatic caliper of
outer sleeve of front drive
shaft
Press fitting casing of
front drive shaft bearing
Disassembling tool of
main teeth oil seal
Press fitting tool of main
teeth oil seal
Disassembling tool of
long semi-axis
Electric cutch tester
Disassembling tool of oil
seal and needle bearingOil seal of long semi-
axis of front axle
Inner oil seal of rear axle
shaft
Needle bearing of long
semi-axis
SST Special tool
Diagram Tool Name tool number Remark
SST Special Tool
Special Service Tool