2006 GREAT WALL SAILOR torque

BR-18
3. Measure the bouncing value of the brake disc face;
Remark: verify the bearing is aligned correctly before
measuring.
The bouncing value of max face: 0.11mm
4. Change the brake disc according to the requirements
(a) Tear down the calipers body from the steering knuckle.
(b) Tear down the hub and the brake disc (See Page SA-11).
(c) Mount the new brake disc and screw up the connecting
bolts according to the specified torque.
Fastening torque
(60
79)N.m
(d) Mount the hub and brake disc assembly (see page SA-12);
(e) Mount the caliper bracket on the steering knuckle and
screw up the bolts according to the specified torque.
Fastening torque
(85
105)N.m
Cylinder Assembly of Wheel-brake
1. Preparation
All parts shall be washed, dried and cleared away the alien
materials before the assembly. And coat moderate vacuum
silicon base grease on the work faces of sliding sleeve dust
cover, sliding sleeve and the sliding liner; and plaster the
moderate rubber lubricant on the work faces of piston, piston
dust cover and the rectangular sealing ring.
2. Encase the piston sealing ring and piston in the caliper body;
(a) Screw the vent screw in the vent hole of calipers.
Fastening torque
(8
13)N.m
(b) Coat moderate rubber lubricant on the work face rectan-
gular sealing ring and encase the caliper body in groove.
(c) Encase the piston in the caliper body.
3. Encase the piston dust cover and the dust cover
snapping ring in the wheel-brake cylinder.
Braking System
Front Brake (Dr)

BR-19
4. Mount the sliding liner, sliding sleeve dust cover and
sliding sleeve.
(a) Encase the sliding liner and sliding sleeve dust cover in
the wheel-brake cylinder.
(b) Ensure the sliding sleeve dust cover in the ring groove of
wheel-brake cylinder hard.
(c) Encase the sliding sleeve in the sliding sleeve dust cover.
(d) Ensure the sliding sleeve dust cover in the ring groove of
sliding sleeve.
Mount of Brake Calipers
1. Mount the brake pad;
2. Mount the wheel-brake cylinder:
(a) Mount the wheel-brake cylinder;
(b) Mount and tighten the two assembling bolts (the bolts
shall be coated with the thread locking sealing agent).
Fastening torque
(38
50)N.m
3. Connect the brake pipeline.
Connect the brake pipeline with the calipers.
Fastening torque
(21
2)N.m
4. Observe the height of brake liquid level and, if
necessary, add in the brake liquid and exhaust the air
in braking system.
Notice: prevent the brake liquid from spraying on the
brake disc when exhausting air.
5. Check to see whether there is leakage of brake liquid. Braking System
Front Brake (Dr)

BR-20
Front Brake
Element figure
spring gasket12
123
separation padssilent pad
brake padbrake caliper
brake pad snapping ring
guide pin lock spring
sealing ringguide pin
dust cover steel gripping hoop
piston dust cover piston brake disc
: fastening torqueN
M
Change of Brake pad
Remark: In case there is a continuous screaming from the front
wheel when braking the vehicle during driving, check the
alarm pad for friction limit for brake pad. If there is friction
trace on the alarm pad with the brake disc, change the brake pad
1. Disassemble the front wheel;
2. Check the thickness of friction material of brake pad.
Check the thickness of friction material of brake pad, if it fails
to be within the specified range, change the brake pad.
Min thickness
2.0mm SFBraking System
Front Brake(SF)

BR-24
2. Measure the thickness of brake disc;
Standard thickness
20.0mm
Min thickness
18.0mm
If the brake pad is scraped, repair it; where the abrasion is
serious and its thickness is smaller than the min thickness,
change the brake disc.
3. Measure the bounding value of the brake disc face;
Remark: the bearing is required to be verified in the suitable
adjustment before measuring.
Max face bouncing value: 0.11mm;
4. Change the brake disc according to the requirement:
(a) Tear down the hub and the brake disc. (see the paragraph
of front wheel hub)
(b) Mount the new brake disc and screw up the connecting
bolts as the specified torque.
(c) Mount the hub and brake disc assembly. (see the para-
graph of front wheel hub).
Fastening torque
(75
5)N
m
(d) Mount the caliper bracket on the steering knuckle and
screw up the bolts according to the specified torque.
Fastening torque
123N
m.
Assembly of Brake-wheel pump
1. Preparation
All parts shall be washed, dried and cleared away the alien
materials, and coat moderate rubber lubricant on the work
faces of piston, piston dust cover and rectangular sealing ring.
2. Encase the piston sealing ring in the caliper body Braking System
Front Brake(SF)

BR-25
3. Encase the piston in the caliper body.
4. Encase the piston dust cover, dust cover steel-
gripping hoop in the caliper body.
Mount of Brake Calipers
1. Mount the brake caliper and screw up the two
mounting bolts.
Fastening torque
123N
m
2. Mount the brake pads;
3. Connecting the brake pipeline;
Use the open spanner to connect the pipeline.
Fastening torque
(21
1)N
m
4. Observe the height of brake liquid level and, if
necessary, add in the brake liquid and exhaust the air
in braking system.
Notice: avoid the brake liquid of spraying on the brake disc
when exhausting the air.
5. Check to see whether there is leakage of brake liquid. Braking System
Front Brake(SF)

BR-26
Rear brake
Element figure
wheel-brake cylinder cluster
pressure spring drag rod
self clearance-
adjusting bracing
wireparking brake arm
flat washer
split pinbrake shoe gear
return spring
parking brake push plate
push-plate spring back brake
shoe
self clearance-
adjusting toggle
tension spring
brake drum
clearance adjuster
pressure spring seatpressure spring front brake shoe
Disassembly of Rear drum-type Brake
Remark: if the braking torque of manual brake cannot satisfies
the braking requirement, it is suggested to check the thickness
of brake shoe liner, where the thickness is less than the min
thickness, change the brake shoe.
Min thickness
1.0mm
1. Tear down the rear wheel;
2. Tear down the brake drum;
Remark: in case the brake drum is not easy to tear down, the
following steps shall be adapted:
(a) Tear down the clearance-adjusting hole; insert a screw-
driver in the brake bottom plate hole to prize up the
adjusting bolt inner tilt angle with the self-adjusting fork.
(b) Use another screwdriver to adjust the adjusting bolt inner
tilt angle to loosen the clearance adjuster of brake shoe. DrBraking System
Rear Brake (Dr)

Parts that cannot be reused after being used

BR-30
Assembly of Rear Brake
remark: assemble the parts according to the
direction in the drawing;
left wheel
right wheel forward
1. Assemble the wheel-brake cylinder:
(a) Coat moderate lithium soap base glycol grease on the
piston cup;
(b) Assemble the wheel-brake cylinder:

Mount the two piston cups on two piston;

Encase the spring and two pistons in the wheel cylinder
body and

Mount the two dust covers
Remark: Assembly shall be conducted correctly according to
the direction shown in the drawing.
2. Mount the wheel-brake cylinder:
(a) Use two bolts to fix the wheel-brake cylinder on the rear
bottom plate.
Coat moderate sealing glue (Glue 704) on the position where
the wheel-brake cylinder connects with the bottom plate.
Fastening torque
(16
20)N
m
(c) Connect the brake pipeline on the wheel-brake cylinder.
Fastening torque
18N
m
3. Coat the following parts with moderate lubricant that
resistant high temperature (do not pollute the friction
plates);
(a) The upper plain of the hex convex platform where the
bottom plate connects the brake shoe;
(b) Contact face of the brake shoe and the top lever of wheel
cylinder;
(c) Contact face of the brake shoe with the support pin. Braking System
Rear Brake (DR)
Assembly of Rear Brake
forward

BR-33
12. Check the clearance between the brake shoe and the
brake drum:
(a) Tear down the brake drum;
(b) Measure the inner diameter of the brake drum and the
outer diameter of brake shoe to check whether the differ-
ence of the two diameters falls within the standard
clearance range.
Shoe clearance: 0.6mm
If it is not correct, check the parking brake system.
13. Mount the brake drum and the rear wheel; screw up
the nuts of rear wheel hub.
Fastening torque
(145
10)N
m
14. Fill the liquid container with brake liquid and exhaust
the air in braking system.
15. Check to see whether there is leakage of brake liquid.
Braking System
Rear Brake (DR)