2006 GREAT WALL SAILOR Power steering system

Preface
With the increase of automobile demand in China, our automobile industry also experiences a rapid
development. The trucks including SUV, manufactured by Great Wall Motor Co., Ltd, which are sold all over
China, are in the leading place in terms of their sales volume, in order to satisfy the demands of various maintain-
ing staff, technicians and managing staff of Changcheng Co., Ltd, we compile this maintenance manual accord-
ing to the latest technological data. This manual covers six vehicle models including Deer, Safe, Sailor, Sing, So
Cool and Pegasus, its main content includes:
Part I is general introduction, which introduces the application index of this manual.
Part II introduces the chassis system, which mainly includes the technologies of dismantle, inspection,
adjustment, repairing, assembly and mount of the clutch, gear box, transfer box, drive shaft, suspension system
and automobile axle, braking system and steering system, etc. each operation approach is illustrated with figure,
which not only presents the maintenance procedure, but also clearly describes the technical requirements and
application limit.
Part III introduces the electric system and air-conditioning system of the automobile body, which mainly
covers such items as the location and content of protective box, power supply system, starting system, lighting
system, combination instrument, backup radar system, wiping and washing system, center control locking and
power window system, acoustical equipment system, full wire harness and air-conditioning system, etc. Electric-
ity diagrams for those electric systems are given in this manual so as to facilitate the maintaining technicians to
find out the problem easily and quickly.
Part IV introduces the external and internal body decoration, which mainly covers the dismantling, inspect-
ing and assembling requirements of the engine cover, front and rear doors, adhesive strip of body collision
avoidance, wheel shield, wrapping angle of wheel-shield and exterior trim panel, front and rear windshields,
side-window glass, rear-door glass, rear platform of cargo compartment, rear door, instrument panel, safety belt,
seat, tail-fin, luggage rack, and reserve tire bracket etc. The dimensions of vehicle body and frame are also given
to maintaining staff for reference during their repairing.
During the narrations of each part, items such as troubleshooting, maintenance notice, maintenance data
and application limit, fastening torques of bolts and nuts for special purpose, SST, SSM and lubricant materials
and so on are also introduced. Various maintenance data are briefed in attachment for reference.
Altogether, this manual is comprehensive in content, visual in illustration, clarifying in requirement and
plain in language. It can be referred by the maintaining staff, technicians and professional managing staff.
Even though we try our best to compile this manual in a strict earnest manner, we cannot guarantee that all
contents in this manual are correct. Therefore, users shall not put forward any claim with Great Wall Company
according to this manual; we are not in the position to hold the responsibility for the loss caused by usage of this
manual. Due to our limited knowledge, it is unavoidable to find error in this manual, any criticism and correction
from you is welcomed.
The final explanation power for this manual is subject to Great Wall Motor Co., Ltd
Compiler
May 2006

SA-4Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ)
5. Adjustment for inner tilt angle of kingpin, outer tilt angle
of front wheel and back tilt angle of kingpin
Item
Inner tilt
angle of
kingpin
Outer tilt
angle of
front
wheelApplicable vehicle type
Dr SL SK SY
SJ
Mechanic
steeringDr SL SK SY
Power
steeringDr
SL SK SY
SJ
Back tilt
angle of
kingpinMechanic
steeringDr SL SK SY
Power steer-
ingDr SL SK SY
SJ9
30
45

14
52

0
30
20

0
10
10

0
20
10

0
30
15

2
45
15

3
15
Location parameter
4. Adjust the wheel angle
Take apart the limit bolts of the steering knuckle to check the
steering angle A of inner wheel.
Inner wheel steering angle
Dr SL SK SY
( 36
40
)
SJ
( 32
34
)
Remark: The wheel should not contact the body or brake hose
when the steering wheel reaches the limit position.
In case the steering angle of inner wheel doesnít conform to the
standard value, adjust the wheel angle through adjusting the
limit bolts of the steering knuckle.
Fastening torque
(90
0)N
m(SJ)
If the wheel angle fails to be adjusted within the standard value,
change the weary or damaged parts of steering system.
If the tilt angle fails to fall within the specified values, make an
adjustment through adding or reducing the gaskets on the
location of upper arm.
Gasket thickness: 3.0, 2.0 and 1.0mm
Once the gasket thickness increases by 1mm, the outer tilt
angle of wheel will change by 7', while the back tilt angle of
kingpin will change 20'.
After the wheel outer tilt angle and the back tilt angle of kingpin
are adjusted, if the inner tilt angle of kingpin still fails to the
specified value, check the steering knuckle or front wheel to
see whether they are bending or loose.
1
50
-20

adjusting bolt
outer tilt
angle of
front wheel inner tilt angle of kingpin
back tilt angle of
kingpin
front AB AB
HPM

SR-1
Notice .......................................................................... SR-2
Troubleshooting .......................................................... SR-2
Inspection on Vehicle .................................................. SR-3
Steering Column ......................................................... SR-4
Manual Steering Gear ................................................. SR-9
Power Steering ............................................................ SR-11
General Introduction ................................................ SR-11
Inspection on vehicle ............................................... SR-13
Power Steering Oil Pump ........................................ SR-16
Power Steering Gear ............................................... SR-18
Steering linkage .......................................................... SR-20
SR
Steering System
Page

SR-2
Notice
The parts change should be conducted correctly because
any error will affect the properties of steering system, or lead
to accidental or damage when driving.
Troubleshooting
Trouble Causes Inspection items
Unsuitable tire inflation
Insufficient lubricant
Over-large inclination
Steering gear joint wear
Lower swing arm ball head wear
Steering column seize-up
Steering gear unsuitable adjustment or damage
Power steering conveyer looseness
Over-low liquid level in oil cup of steering pump
Failure in power steering mechanismInflate the tire to specified pressure
Lubricating the hanging devices
Check the Alignment of Front Wheel
Change the Steering gear joint
Change the lower swing arm ball
head;
Check the steering column
Adjust or repair the gear.
Adjust the conveyor.
Check the steering pump oil cup
Check the power steering devices
Poor returning
Unsuitable tire inflation
Insufficient lubricant
Incorrect wheel alignment
Steering column seize-up
Steering gear unsuitable adjustment or damageInflate the tire to specified pressure
Lubricating the hanging devices.
Check the Alignment of Front
Wheel
Check the steering column
Change the steering gear.
Over-large playFront wheel bearing wear
Steering drive shaft yoke wear
Lower swing arm ball head wear
Steering gear joint wear
Steering gear unsuitable adjustment or damageChange the front bearing
Change the steering drive shaft
Change the swing arm ball head
Change the steering gear joint
Change the steering joint
Abnormal noise
Steering drive lever looseness
Steering gear joint wear
Steering gear unsuitable adjustment or damage
Oil lack or poor sealing of steering machine.Tighten the steering drive lever
Change the steering gear joint
Change the steering gear
Add the oil or change the sealing
washer Steering system inspection
on vehicle.
Steering System
Notice and Troubleshooting
Difficulty in steering

SR-11Steering System
Power Steering (General Introduction)
power steering oil pump
power steering gear steering drive shaft
oil cup
Power steering
Introduction
Principal of Power Steering
The power steering is a kind of hydraulic device that use
the engine power to steer. The engine drive the power
steering oil pump to generate the hydraulic pressure, which
actuates the piston in steering gear, so that the worm shaft
can provide to the piston with a supplementary force, which
has relation with the pressure actuated on the piston.
Therefore, pressure increase is required if larger steering
force is needed, and the pressure variation is accomplished
through the control valve.
Intermediate position (forward straightly)
The liquid from the power steering oil pump is sent to
the control valve, which, if locates at the intermediate, will
allow the liquid to pass and enter into the drain outlet, finally
return the pump. At this time, it is difficult to increase the
pressure; meanwhile, due to the equal pressures at the both
sides of the power piston, it cannot move toward either side.
Steering time
When the steering drive shaft move toward either side,
the control valve will move together with it, in case one oil
passage is shut off, meanwhile open the other larger, the
liquid flow variation will increase the pressure, as result, the
unequal pressure at both sides of piston will make the piston
move toward the side of smaller pressure, therefore, the
liquid is pressed in the pump through the control valve.
pump control valve
drain outlet
power cylinde
power piston
segmental gear shaft worm shaftsteering gear
Pump

SR-12Steering System
Power Steering (Introduction)
Suggestion on maintenance
The failure of power steering system usually relates to the
steering difficulty due to lack of supplementary force. In such
case, it is the first to verify the problem is produced by the pump
or steering gear when repairing. In doing so, the problem can be
checked on vehicle with the pressure meter.
On-vehicle Inspection
As the power steering is a hydraulic pressure device, its
trouble usually caused by the lack of specified hydraulic
pressure or the abnormal work of control valve. As a result, it
cannot acquire the moderate hydraulic pressure.
In case the problem is caused by the pump, the steering
wheel will deflect toward right or left. On the other side, if the
problem is caused by control valve, when the steering wheel
rotates to left or right, the steering will become more difficult
due to the unequal supplementary force. However, when there
is wear on the piston sealing ring of power cylinder, it also cause
the hydraulic pressure loss that may lead into steering difficulty
toward right or left.
Before making inspection on vehicle, verify the power
steering system firstly to see whether there is air. If any, the air
volume will increase with the variation of hydraulic pressure,
which will cause the hydraulic pressure fluctuation that makes
the power steering work abnormally. In order to verify whether
there is any air in the system, check whether the liquid level
varies or not when the steering wheel rotates completely toward
the right or left. For instance, if there is air in the system, the air
will be compressed, which will reduce the liquid level
remarkably, when the steering wheel rotating. If there is no air
in system, the liquid level variation is very small even though
the hydraulic pressure increases. This is because the liquid
volume will not varies when being compressed. And the small
liquid level variation is caused by the expansion of hose
between the pump and steering gear when the hydraulic pres-
sure increasing.
Meanwhile, the air in system sometimes will cause the
pump or steering gear produce noise when the steering wheel
rotating completely toward a certain direction. After checking
or exchanging the pump or steering gear, the on-vehicle inspec-
tion should be often conducted to guarantee the normal work of
power steering system.

SR-13Steering System
Power Steering (On-Vehicle Inspection)
tensioning wheelpower steering oil
pump
crankshaftOn-vehicle inspection
Inspection on tension of driver conveyor
Measure the tension of drive conveyor.
Drive conveyor tension: under the condition of 98 N.
New conveyor: (5-7)mm
Old conveyor:
(7-9)mm
Remark:
ìnew conveyorî means the conveyor that is used on the
machine less than five minutes;
ìold conveyorî means the conveyor that is used on machine
more than five minutes
Check for height of liquid level
1. Keep the body in horizontal status
2. Increase the liquid temperature
When the engine runs idly by 1000 r/m or less, rotate the
steering wheel several times from the locking position to the
reverse locking position to increase the liquid temperature.
3. Check to see whether there is foam or emulsification;
Remark: the foam or emulsification shows there is air in the
system or the liquid level is over-low.
4. Check the liquid level height in oil cup;
Check the liquid level height and, if needed, add the oil.

SR-14Steering System
Power Steering (On-Vehicle Inspection)
Change of power steering liquid
1. Tear down the oil-returning hose from the oil cup to
drain the liquid into the container;
2. Run the engine in the idle status, and rotate the
steering wheel toward the max rotating angle for
several times in right or left direction while draining the
liquid, until the oil in steering liquid is drained up.
3. Turn off the engine.
4. Connect the oil-returning pipe and inject the new
power steering liquid in the liquid tank;
Hydraulic oil type: No.8 Liquid drive oil (Q/SH003.01.012-88)
5. Start the engine, and make it running in the idle status.
Rotate the steering wheel to the max rotating angle repeatedly
several times, meanwhile, supplement new power steering
liquid in the liquid tank until there is no foam or turbidities in
the liquid tank, and the oil indicating lamp reaches the marked
range when the engine is turned off.
6. Tighten the liquid tank cover
7. Exhaust the air in the power steering system;
Ai-r bleeding in power steering system
1. Check the liquid level height in the liquid tank
Check the liquid level and, if needed, supplement the liquid.
2. Start the engine in the idle status and rotate the
steering wheel repeatedly to the max rotating angle
several times.
3. Turn off the engine and connect the ethane pipe and
bleeding plug.
4. Start the engine and rotate the steering wheel
repeatedly to the max rotating angle several times.
5. Locate the steering wheel at the intermediate position.