2006 FORD F650 tire size

Check to make sure that the axle mounting U-bolt nuts, attaching or
mounting bolts and nuts are securely tightened. Regularly check front
axle for damage, binding, worn parts and adequate lubrication.
At regular intervals, or during other scheduled maintenance, (tire
rotation/service, wheel bearing service, alignment, etc.) the kingpins
should be checked for excessive wear. Refer to the service manual for
proper procedures.
Toe-in setting - general inspection
Inspecting steer axle tires in the first 3,000–10,000 service miles
(4,800–16,000 service km) will generally show if tires are wearing
normally.
Rapid outside shoulder wear on both tires indicates too much toe-in.
Rapid inside shoulder wear on both tires indicates too much toe-out. In
P&D-type service, left-to-right steer tire tread life differentials up to 40%
can be observed depending on routes and other variables.
Follow the tire manufacturer’s recommended cold inflation pressure for
the tire size, load range (ply rating) and steer axle loading typical for
their operation (each steer axle tire will equal
12steer axle loading).
Special applications may warrant a setting based on past experience with
the type of tire operating loads and conditions. Radial tires are more
sensitive to toe-in setting than bias ply tires. While not insensitive to
vehicle alignment, fine tuning school bus alignment to line-haul truck
standards will not drastically improve tire tread life.
It is essential that correct toe-in and tire pressure be maintained for
optimum tire wear.
Rear axle - general inspection
Check to make sure that the axle mounting U-bolts, attaching or
mounting bolts and nuts are securely tightened. Refer toU-bolt nut
torquein this chapter. Regularly check the rear axle for damaged,
binding or worn parts.
NoSpin Detroit Locker positive locking differential
Vehicles equipped with this type differential have the operator’s manual
supplied with the vehicle. Refer to this manual for maintenance checks.
Brake system - general inspection
Your vehicle is equipped with non-asbestos brake linings. However,
exposure to excessive amounts of brake material (whether asbestos or
2006 F-650/750(f67)
Supplement
USA(fus)
Maintenance and Specifications
170

•Always loosen rim clamps before complete removal of nut from stud
(cast spoke wheels). With loosened nuts on stud, strike clamps with a
heavy hammer and be sure each clamp is loose.
•Always deflate tires completely before removing locks or side rings.
•Always inflate tires in a safety cage.
•Never mix rim side rings or lock rings of different types,
manufacturers or sizes.
•Never use cracked, bent or badly rusted parts.
•Never re-inflate flat tires on-vehicle; use the spare tire.
•Never add air until each side ring or lock ring is fully seated.
•Never hammer side ring or lock ring on a partially- or fully-inflated
tire.
Proper torque
It is important to tighten and maintain wheel and rim mounting nuts to
the proper torque. Loose nuts or over-tightened nuts can lead to
premature wear and possible failure of the wheel and/or mounting
hardware.
Changing wheel types
Consult your dealer or wheel/rim distributor before attempting any wheel
or fastener changes.
Use only the same type and style wheels and mounting hardware
to replace original parts. Failure to do so may result in an
assembly that looks fine, but does not fit together properly. This could
possibly cause wheel or fastener failures which could result in property
damage, personal injury or death.
Note:Do not attempt to mix stud-piloted wheels or fasteners with
hub-piloted wheels or fasteners.
Note:Do not change from aluminum wheels to steel wheels or
vice-versa without changing the mounting hardware required or, with
flange-nut mounting systems, changing the hub and stud assembly.
2006 F-650/750(f67)
Supplement
USA(fus)
Maintenance and Specifications
213

WHEEL NUT TORQUE
Size Nut mountingTorque
Ft. lb. N•m
22 mm Flange 450–500 610–678
Note:Do not use lubrication on dry threads. Where excessive corrosion
exists, a light coat of lubricant on the first three threads of the stud bolt
is permitted. Keep lubricant away from:
•Hex nut and rim clamp contact surfaces.
•Cap nut ball face and ball seat on the disc wheel.
•Flange nut washer surface and flat on the disc wheel.
TIRE/WHEEL RIM SELECTION AND INFLATION PRESSURES
Tire sizeLoad
rangeApproved
rim widthsAxle capacity
Front - lb.
(kg)/psi
(kPa)Rear - lb.
(kg)/psi
(kPa)
225/70R19.5 F 6.00, 6.757280 (3302) /
95 (655)13660 (6196) /
95 (655)
245/70R19.5 F 6.75, 7.508160 (3701) /
85 (586)15440 (7003) /
85 (586)
245/70R19.5 G 6.75, 7.509090 (4123) /
100 (690)17640 (8001) /
100 (690)
265/70R19.5 G6.7510000 (4536) /
115 (793)19440 (8817) /
115 (793)
7.50, 8.2510710 (4858) /
120 (827)20280 (9199) /
120 (827)
9R22.5 F 6.75, 7.509080 (4118) /
105 (724)17200 (7801) /
105 (724)
10R22.5 F6.7510000 (4536) /
100 (690)19760 (8963) /
100 (690)
7.5010410 (4722) /
100 (690)19760 (8963) /
100 (690)
2006 F-650/750(f67)
Supplement
USA(fus)
Maintenance and Specifications
214

Tire sizeLoad
rangeApproved
rim widthsAxle capacity
Front - lb.
(kg)/psi
(kPa)Rear - lb.
(kg)/psi
(kPa)
10R22.5 G6.7510000 (4536) /
115 (793)20000 (9072) /
115 (793)
7.5011350 (5148) /
115 (793)21420 (9716) /
115 (793)
11R22.5 G 7.50, 8.2512350 (5602) /
105 (724)23000 (10432)
/ 105 (724)
11R22.5 H 7.50, 8.2513220 (5996) /
120 (827)23800 (10795)
/ 110 (758)
12R22.5 H8.2514400 (6531) /
120 (827)27120 (12301)
/ 120 (827)
9.0014780 (6704) /
120 (827)27120 (12301)
/ 120 (827)
245/75R22.5 G 6.75, 7.509350 (4241) /
110 (758)17640 (8001) /
110 (758)
255/70R22.5 H6.7510000 (4536) /
115 (793)19660 (8917) /
115 (793)
7.50, 8.2511020 (4998) /
120 (827)20280 (9199) /
120 (827)
265/75R22.5 G 7.50, 8.2510410 (4722) /
110 (758)19220 (8718) /
100 (690)
275/70R22.5 H7.5013220 (5996) /
120 (827)24800 (11249)
/ 120 (827)
8.2513460 (6105) /
120 (827)24800 (11249)
/ 120 (827)
275/80R22.5 G 7.50, 8.2512350 (5602) /
110 (758)22700 (10296)
/ 110 (758)
295/75R22.5 G 8.25, 9.0012350 (5602) /
110 (758)23900 (10841)
/ 100 (690)
2006 F-650/750(f67)
Supplement
USA(fus)
Maintenance and Specifications
215

Tire sizeLoad
rangeApproved
rim widthsAxle capacity
Front - lb.
(kg)/psi
(kPa)Rear - lb.
(kg)/psi
(kPa)
295/80R22.5 H8.2514400 (6531) /
120 (827)27760 (12591)
/ 120 (827)
9.0014780 (6704) /
120 (827)27760 (12591)
/ 120 (827)
Tire inflation information
All tires with Steel Carcass Plies (if equipped):
This type of tire utilizes steel cords in the sidewalls. As such, they
cannot be treated like normal light truck tires. Tire service, including
adjusting the air pressure, must be performed by personnel trained,
supervised and equipped according to Federal Occupational Safety and
Health Administration (OSHA) regulations. For example, during any
procedure involving tire inflation, the technician or individual must
utilize a remote inflation device, and ensure that all persons are clear of
the trajectory area.
WARNINGAn inflated tire and rim can be very dangerous if
improperly used, serviced or maintained. To avoid serious injury,
never attempt to re-inflate a tire which has been run flat or seriously
under-inflated without first removing the tire from the wheel assembly
for inspection. Do not attempt to add air to tires or replace tires or
wheels without first taking precautions to protect persons and
property.
2006 F-650/750(f67)
Supplement
USA(fus)
Maintenance and Specifications
216