2006 FORD F150 garage door opener

When programming your HomeLinkWireless Control System to
a garage door or gate, be sure that people and objects are out of
the way to prevent potential harm or damage.
Do not use the HomeLinkWireless Control System with any garage
door opener that lacks safety stop and reverse features as required by
U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLinkat:www.homelink.comor1–800–355–3515.
Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLinkequipped vehicle
purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelinkbuttons be erased for security purposes, refer to
Programmingin this section.
Programming
Do not program HomeLinkwith the vehicle parked in the garage.
Note:Your vehicle may require the ignition switch to be turned to the
ACC position for programming and/or operation of the HomeLink.Itis
also recommended that a new battery be placed in the hand-held
transmitter of the device being programmed to HomeLinkfor quicker
training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outside
buttons releasing only when the
indicator light begins to flash after
20 seconds.Do notrepeat Step 1
to program additional hand-held
transmitters to the remaining two
HomeLinkbuttons. This will erase
previously programmed hand-held
transmitter signals into HomeLink.
2. Position the end of your
hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink
button you wish to program (located on your visor) while keeping the
indicator light in view.
2006 F-150(f12)
Owners Guide (post-2002-fmt)
USA(fus)
Driver Controls
79

3. Simultaneously press and hold
both the HomeLinkand hand-held
transmitter button.Do not release
the buttons until Step 4 has
been completed.
Some entry gates and garage door
openers may require you to replace
Step 3 with procedures noted in the
“Gate Operator and Canadian Programming” in this section for Canadian
residents.
4. The indicator light will flash slowly and then rapidly. Release both
buttons when the indicator light flashes rapidly. (The rapid flashing light
indicates acceptance of the hand-held transmitters’ radio frequency
signals.)
5. Press and hold the just-trained HomeLinkbutton and observe the
indicator light. If the light is constant, programming is complete and your
device should activate when the HomeLinkbutton is pressed and
released.Note:To program the remaining two HomeLinkbuttons,
begin with Step 2 in the “Programming” section —do notrepeat Step 1.
Note:If the indicator light blinks rapidly for two seconds and then turns
to a continuous red, proceed with Steps 6 through 8 to complete
programming of a rolling code equipped device.
6. At the garage door opener receiver (motor-head unit) in the garage,
locate the “learn” or “smart” button (usually near where the hanging
antenna wire is attached to the unit).
7. Press and release the “learn” or “smart” button. (The name and color
of the button may vary by manufacturer.)
Note:There are 30 seconds in which to initiate Step 8.
8. Return to the vehicle and firmly press, hold for two seconds and
release the HomeLinkbutton. Repeat the press/hold/release sequence
again, and, depending on the brand of the garage door opener (or other
rolling code equipped device), repeat this sequence a third time to
complete the programming.
HomeLinkshould now activate your rolling code equipped device. To
program additional HomeLinkbuttons begin with Step 2 in the
“Programming” section. For questions or comments, please contact
HomeLink atwww.homelink.comor1–800–355–3515.
2006 F-150(f12)
Owners Guide (post-2002-fmt)
USA(fus)
Driver Controls
80

Gate Operator & Canadian Programming
During programming, your
hand-held transmitter may
automatically stop transmitting —
not allowing enough time for
HomeLinkto accept the signal
from the hand-held transmitter.
After completing Steps 1 and 2
outlined in the“Programming”
section, replace Step 3 with the following:
Note:If programming a garage door opener or gate operator, it is
advised to unplug the device during the “cycling” process to prevent
overheating.
•Continue to press and hold the HomeLinkbutton (note Step 3 in the
“Programming” section) while you press and release —every two
seconds(“cycle”) your hand-held transmitter until the frequency
signal has been accepted by the HomeLink. The indicator light will
flash slowly and then rapidly after HomeLinkaccepts the radio
frequency signal.
•Proceed with Step 4 in the “Programming” section.
Operating the HomeLinkWireless Control System
To operate, simply press and release
the appropriate HomeLinkbutton.
Activation will now occur for the
trained product (garage door, gate
operator, security system, entry
door lock, or home or office lighting
etc.). For convenience, the
hand-held transmitter of the device
may also be used at any time. In the event that there are still
programming difficulties, contact HomeLinkatwww.homelink.comor
1–800–355–3515.
2006 F-150(f12)
Owners Guide (post-2002-fmt)
USA(fus)
Driver Controls
81

checking and adding ..............280
dipstick ....................................280
filter, specifications ........283, 312
recommendations ...................283
refill capacities ........................313
specifications ..................316, 319
Exhaust fumes ..........................204
F
Fail safe cooling ........................290
Floor mats ...................................93
Fluid capacities .........................313
Foglamps .....................................55
Four-Wheel Drive vehicles .......219
driving off road .......................223
electronic shift ................221–222
indicator light .........................219
lever operated shift ................220
preparing to drive your
vehicle .....................................209
Fuel ............................................292
calculating fuel
economy ............................87, 297
cap ...........................................294
capacity ...................................313
choosing the right fuel ...........295
comparisons with EPA fuel
economy estimates .................300
detergent in fuel .....................296
filling your vehicle
with fuel ..................292, 294, 297
filter, specifications ........292, 312
fuel pump shut-off switch .....237
improving fuel economy ........297
octane rating ...................296, 319
quality ......................................296
running out of fuel .................297
safety information relating
to automotive fuels ................292Fuel pump shut-off switch .......237
Fuses ..................................237–238
G
Garage Door Opener
(see Homelink wireless
control system) ...........................78
Gas cap (see Fuel cap) ............294
Gas mileage
(see Fuel economy) .................297
Gauges .........................................19
H
Hazard flashers .........................236
Head restraints .................111, 115
Headlamps ...................................53
aiming ..................................55–56
autolamp system .......................53
bulb specifications ....................59
daytime running lights .............54
flash to pass ..............................54
high beam .................................54
replacing bulbs .........................60
turning on and off ....................53
Heating
heater only system ...................43
heating and air
conditioning system .....44, 46, 49
Homelink wireless control
system ..........................................78
Hood ..........................................275
I
Ignition ...............................201, 319
Infant seats
(see Safety seats) .....................150
2006 F-150(f12)
Owners Guide (post-2002-fmt)
USA(fus)
Index
331