2006 DODGE VIPER turn signal bulb

Turn Signals
Move the Multi-Function Control Lever up or down and
the arrows on each side of the instrument cluster flash to
show proper operation of the front and rear turn signal
lights. You can signal a lane change by moving the lever
partially up or down without moving beyond the detent.If either light remains on and does not flash, or there is a
very fast flash rate, check for a defective outside light
bulb. If an indicator fails to light when the lever is
moved, it would suggest that the fuse or indicator bulb is
defective.
Highbeam/Lowbeam Select Switch
Pull the Multi-Function Control Lever towards you to
switch the headlights to HIGH beam. Pull the control
lever a second time to switch the headlights to LOW
beam.
Flash to Pass
You can signal another vehicle with your headlights by
lightly pulling the multi-function lever toward the steer-
ing wheel. This will cause the headlights to turn on at
high beam and remain on until the lever is released.
Turn Signal Lever
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Turn Signal Indicators
The arrows will flash in unison with the corresponding
exterior turn signal when using the signal lever. (See page
80 for more information.)
Hazard Indicator
Both turn signal arrows will flash in unison with all front
and rear turn signals when the hazard warning switch is
used.
NOTE:Leaving the hazard flashers on for extended
periods of time will wear down the battery.
Message Center
Message Center Components
Anti-Lock Warning Light
The amber ABS Warning Light will come on
when the ignition is first turned on, and stay on
briefly as a bulb check. If the bulb does not
come on during starting, have the bulb re-
paired promptly. This light also illuminates to indicate
that the Antilock Brake System self-check is in process at
vehicle start-up. If the light remains on after start-up, or
comes on and stays on at road speeds, it may indicate
that the ABS has detected a malfunction or has become
inoperative. In this case, the system reverts to standard
non-antilock brakes. Turn the engine off and on again to
reset the Antilock Brake System. If the light remains on,
see your authorized dealer. If both the red BRAKE and
amber ABS warning lights are on and the parking brake
is fully released, see your authorized dealer immediately.
UNDERSTANDING YOUR INSTRUMENT PANEL 91
4

▫Headlight, Parking, Front Park, Turn Signal, Front
Sidemarker And Front Fog Light Removal....212
▫High Intensity Discharge Headlights (HID) . . . 214
▫Tail, Tail/Stop, And Marker Lamp Bulb
Replacement.........................214
▫Backup And Rear Turn Signal Lamp Bulb
Replacement.........................215
▫License Plate Light....................218
Headlight Aiming......................219
▫Aiming Check.......................219

Fluids And Capacities...................220

Fluids, Lubricants And Genuine Parts........221
▫Engine.............................221
▫Chassis............................222
▫Body..............................223
MAINTAINING YOUR VEHICLE 167
7

Exterior Light Bulbs — Coupe Models
Headlight-Low/High Beam.... Servicedatdealer only
Aux. Headlight-High Beam.........(HB3A) 9005XS
Front Park/Turn......................3157AK
Fog Light.......................(H10 U) 9145
Front Sidemarker.......................2886X
Center Stop Light.......... 16LED(not serviceable)
Rear Tail/Stop/Turn.....................3157
Rear Marker Light........................ 194
Back up Light..........................3157
License................................ 168
Rear Compartment Light................... 168
NOTE:You will note that upon turning the (HID) High
Intensity Discharge Headlamp Bulbs on, there is a blue
hue to the lamps. This diminishes and becomes more
white after approximately 10 seconds as the system
charges.
EXTERIOR LIGHT BULB SERVICE
Headlight, Parking, Front Park, Turn Signal, Front
Sidemarker and Front Fog Light Removal
1. Remove the splash shield.
212 MAINTAINING YOUR VEHICLE

2. Twist sockets counter-clockwise to pull out bulbs.
Replace tail, tail/stop, or marker lamp bulb.
3. Reinstall the appropriate bulb and socket assembly.
Replace the access panel. Close the trunk.Backup and Rear Turn Signal Lamp Bulb
Replacement
1. Open the trunk. Remove two access panel fasteners.
Remove the access panel.
MAINTAINING YOUR VEHICLE 215
7

3. Twist sockets of the three bulbs shown counter-
clockwise. Disconnect bulb and socket assemblies from
the upper lamp assembly. Pull the upper lamp assembly
clear in order to access backup and rear turn signal lamp
bulbs.4. Replace the backup or rear turn signal lamp bulb.
Reinstall the appropriate bulb and socket assembly. Re-
install the three bulb and socket assemblies in the upper
lamp assembly. Reinstall the upper lamp assembly. Re-
place the access panel. Close the trunk.
MAINTAINING YOUR VEHICLE 217
7