2006 DODGE VIPER horn

To Lock the Doors:
NOTE:To enable/disable the Lamp Flash, see proce-
dure described above.
Press and release the LOCK button on the transmitter.
The horn will chirp once and the park and tail lights will
blink to acknowledge that the door is locked and that the
alarm system is armed. The horn chirp can be disabled at
the dealership if so desired.
NOTE:The horn chirp feature can be enabled or dis-
abled by performing the following procedure:
1. Press and hold the Lock button on the transmitter.
2. Continue to hold the Lock button, wait at least 4 but
no longer than 10 seconds, then press the Unlock button.
3. Release both buttons.
To Unlock the Trunk/Liftgate:
Press and hold the trunk/liftgate button on the transmit-
ter to unlatch the trunk/liftgate. The front and rear
park/turn signal lights will blink 3 times.
Panic Alarm
The panic alarm unlocks the driver’s door, turns on the
interior lights, flashes the park and fog lights and sounds
the horn for 3 minutes or until the alarm is turned off.
Panic mode does not work when the vehicle is driven.
To Use the Panic Alarm:
Press and hold the Panic button to activate the alarm.
Press and hold the Panic button or turn the key in the
ignition to the RUN position to deactivate the alarm. The
alarm will also shut itself off after 3 minutes.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Transmitter Battery Service
The replacement battery number is 2016. This is a generic
battery, readily available at local retail stores.
1. Pry the transmitter halves apart with a coin or similar
object.2. Remove and replace the batteries.
3. Reassemble the transmitter case and test operation.
NOTE:If the transmitter is operated more than 255
times out of range of the vehicle (23 feet or 7 meters) or
when the vehicle battery is dead, it may become “out of
synch”. The result is that the transmitter will not func-
tion.
To correct this condition, remove the key from the
ignition and close the hood and all doors. Press both
buttons on the transmitter for about 10 seconds. The horn
will chirp once to acknowledge the signal. Normal trans-
mitter operation should resume.
Separating Transmitter Halves
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

VEHICLE THEFT ALARM
The system monitors the doors, trunk/liftgate, hood, and
ignition for unauthorized operation.
Once the system has been armed, opening any door,
trunk/liftgate (with the ignition key), hood or turning the
ignition key to any position will trigger an alarm.
If something triggers the alarm, the system will signal for
about 18 minutes. For the first 3 minutes the horn will
sound and the park, tail and fog lights will flash. If the
condition which triggered the alarm is still present, the
park, tail and fog lights will continue to flash for 15
minutes, unless the trigger condition is cleared sooner.
NOTE:The engine will not start until the system is
disarmed.
To Arm the Vehicle Theft Alarm System
There are two methods to arm the Vehicle Theft Alarm
system:
1. Press the Lock button on the Remote Keyless Entry.
The optical and audible horn chirp will sound if it is
enabled. (See Remote Keyless Entry section of this
manual)
2. Remove the keys from the ignition and, with the door
open, press the Lock button on the door trim panel and
close the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
2

2. Or, press the UNLOCK button on the Remote Keyless
Entry transmitter. The front and rear park and turn signal
lights will flash to acknowledge the signal. (See the
Remote Keyless Entry Section of this manual for opera-
tion)
NOTE:The vehicle will not start unless the Vehicle
Theft Alarm System is disarmed by either of the two
methods above. Inserting the key in the ignition WILL
NOT disarm the system (it will start the alarming pro-
cess!)Tamper Alert
If the horn sounds 3 times when you unlock the vehicle
using the Remote Keyless Entry transmitter or key, the
alarm has been activated. Check the vehicle for tamper-
ing.
NOTE:If the Security lamp flashes twice every 6
seconds, then the vehicle was tampered with.
Keyless Entry Transmitter
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Cycle the ignition from OFF to ACC four times with-
out going into ON. Leave the switch in the OFF position
after the fourth cycle.
3. Depress the driver’s side Power Door Lock switch in
the UP direction. A single chime and a horn chirp indicate
that the process has begun.4. Remove the key from the ignition and exit the vehicle.
5. The feature is cancelled when the ignition is cycled to
ON/RUN.
6. The vehicle will enter Battery Save Mode 45 seconds
after all doors are closed.
NOTE:The remote keyless entry and passenger exterior
door handle will not work when the Battery Save feature
is enabled. Enter the vehicle either by using the key to
open the door manually or by using the outside door
handle.
NOTE:The Vehicle Theft Alarm is disabled when the
vehicle is in Battery Save mode. Therefore, the vehicle is
not protected when the Battery Save feature is enabled.
NOTE:The exterior and interior lighting functions will
not work when the vehicle is in Battery Save Mode.
Exit Battery Save Mode by doing the following:
Ignition Key Positions
MAINTAINING YOUR VEHICLE 183
7

Cavity Fuse Circuits
23, 24 Mini
Fuse 10
Amp RedAirbag, Ignition Run
25-29 ISO RE-
LAYBatt-Relay Contact, High Blower
Motor
30-34 MICRO
RELAYBatt-Relay-Starter Contact to So-
lenoid
35-39 MICRO
RELAYFeed-Auto Shutdown Relay Coil
40-44 MICRO
RELAYFeed-Horn (From Relay)
45-49 MICRO
RELAYBatt-Relay-Headlamps
50-54 MICRO
RELAYRelay-A/C Clutch Output from
Relay Contact (B+)
55-59 MICRO
RELAYLeft/Right Downstream Oxygen
Sensor Output Feed FRCavity Fuse Circuits
60, 61 Mini
Fuse 15
Amp
BlueIgnition Start/Run Relay Coil
62, 63 Mini
Fuse 15
Amp
BlueIgnition Start/Run Gauges
64, 65 Mini
Fuse 10
Amp RedIgnition Start/Run Airbag
66, 67 Mini
Fuse 20
Amp
YellowFeed-Ign Run/Acc Wiper Switch
MAINTAINING YOUR VEHICLE 207
7