2006 DODGE VIPER trunk

5. Fold the convertible top cover again. Place the cover
into the bag. Store the cover in the trunk or a dry secure
area.CONSOLE FEATURES
The front console has a removable ashtray, power outlet/
cigarette lighter and power window switches.
The center console compartment is equipped with a
cigarette lighter/power outlet and a passenger airbag
on/off switch.
Folding Boot Cover
Console
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Trunk/Liftgate Ajar Light
This light indicates that the trunk/liftgate is not
latched.
Engine Coolant Temperature Light
A red LED light on the Coolant Temperature
gauge will illuminate to warn of an overheated
engine coolant condition.
Low Oil Pressure Light
A red LED light on the Oil Pressure gauge will
illuminate to indicate low engine oil pressure. The
light should come on briefly as a bulb check when the
engine is first started. If the light stays on or comes on
while driving, stop the vehicle and shut off the engine.
DO NOT operate the vehicle until the cause is corrected.
NOTE:This light does not indicate how much oil is in
the engine. The engine oil level must be checked using
the procedure shown in section 7. (See page 172 for more
information.)
Charge System Light
A red LED light on the Voltage gauge will illumi-
nate when there is a charging system malfunction
or a possible accessory drive belt failure.
CAUTION!
The accessory belt also drives the water pump.
Operating the vehicle with a failed belt can cause
engine overheating and possible severe engine dam-
age.
Fog Light ON Indicators
This light indicates that the front fog lights are on.
(See page 79 for more information.)
This light indicates that the rear fog lights are on.
94 UNDERSTANDING YOUR INSTRUMENT PANEL

•Guard against carbon monoxide with proper mainte-
nance. Have the exhaust system inspected every time
the vehicle is raised. Have any abnormal conditions
repaired promptly. Until repaired, drive with all side
windows fully open.
•Keep the trunk/liftgate closed when driving your
vehicle to prevent carbon monoxide and other poison-
ous exhaust gases from entering the vehicle.
ADDING FUEL
The fuel tank filler tube has a restricting door about 2
inches (50mm) inside the opening. If using a portable
container, it should have a flexible nozzle long enough to
force open the restricting door.
WARNING!
Remove the fuel tank filler tube cap (gas cap) slowly
to prevent fuel spray from the filler neck that may
cause injury. The volatility of some gasolines may
cause a buildup of pressure in the fuel tank that may
increase while you drive the vehicle. This pressure
can result in a spray of gasoline and/or vapors when
you remove the cap from a hot vehicle. Removing the
cap slowly allows the pressure to vent and prevents
fuel spray. Never have any smoking materials lit in
or near the vehicle when the fuel tank filler tube cap
(gas cap) is removed or when filling the tank. Never
fill the gas tank while the engine is running.
152 STARTING AND OPERATING

Hood Latch
When performing other underhood services, the hood
latch release mechanism and safety catch should be
inspected, cleaned, and lubricated.
It is important to maintain proper lubrication to insure
that the hood mechanisms work properly and safely.
Multi-Purpose Lubricant, NLGI Grade 2, should be ap-
plied sparingly to all pivot and sliding contact areas.
Other Body Mechanisms
The following body mechanisms should be inspected
and, if necessary, all pivot and sliding contact areas of
these components should be lubricated with the lubricant
specified as follows:
Smooth White Body Lubricant - Such as Mopar Spray
White Lube or equivalent:
•Hood hinge
•D/ lid hinge
•Fuel door hinge
•Lock cylinders
•Parking brake mechanism
•Trunk/liftgate latches
•Ash tray
Points That Should Not Be Lubricated
There are many points that should not be lubricated;
some because they are permanently lubricated, some
because lubricants will be detrimental to the operating
characteristics, and some because lubricants will cause
component failures.
In particular, do not lubricate rubber bushings, since this
not only will cause them to fail, but will destroy their
necessary frictional characteristics.
188 MAINTAINING YOUR VEHICLE

Check the battery every 4 to 6 weeks to ensure that the
voltage is above 12.40. Voltage will drop more rapidly
in hot temperatures. If battery voltage drops below
12.40, follow the battery recharge procedure in the
Service Manual.
•Check that the radiator coolant level of protection is to
at least -20°F (-29°C).
•Block the wheels. Do not apply the Parking Brake.
•Make sure that all tires are inflated to the optimum
pressure, (29 PSI).
•Cut blocks of plywood about the same size of the tires.
Cover each block with indoor/outdoor carpeting and
place them between the tires and concrete. This will
prevent tire flat spotting.
•For long term storage, remove the tires and put the
vehicle up on blocks. Stack the tires on plywood and
cover with a tarp to prevent flat spotting.
•Move the wiper blades away from the windshield.
NOTE:To help prevent the battery from discharging
during shorter periods of inactivity, perform the follow-
ing:
1. Make sure that the trunk/liftgate, hood, doors, win-
dows and convertible top are completely closed.
2. Make sure that remote transmitter is operating and
that the battery is good.
3. Make sure that the hood, trunk/liftgate and door
switches are in adjustment. Perform the quick system
check which follows.
Use the remote transmitter to set the alarm. If the alarm
SET light comes on and flashes, the system is operating
properly. If not, there is a problem with a switch or the
system. See your dealer for service.
210 MAINTAINING YOUR VEHICLE

High Intensity Discharge Headlights (HID)
The headlights are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlight switch off and the key removed.Because of
this, you should not attempt to service a headlight bulb
yourself. If a headlight bulb fails, take your vehicle to
an authorized dealer for service.
WARNING!
A transient high tension occurs at the bulb sockets of
High Intensity Discharge (HID) headlights when the
headlight switch is turned ON. It may cause serious
electrical shock or electrocution if not serviced prop-
erly. See your authorized dealer for service.
NOTE:If High Intensity Discharge (HID) lights are not
working, recycle the headlight switch 4 times to see if it
will restrike.
Tail, Tail/Stop, and Marker Lamp Bulb
Replacement
1. Open the trunk. Remove two access panel fasteners.
Remove the access panel.
214 MAINTAINING YOUR VEHICLE

2. Twist sockets counter-clockwise to pull out bulbs.
Replace tail, tail/stop, or marker lamp bulb.
3. Reinstall the appropriate bulb and socket assembly.
Replace the access panel. Close the trunk.Backup and Rear Turn Signal Lamp Bulb
Replacement
1. Open the trunk. Remove two access panel fasteners.
Remove the access panel.
MAINTAINING YOUR VEHICLE 215
7

3. Twist sockets of the three bulbs shown counter-
clockwise. Disconnect bulb and socket assemblies from
the upper lamp assembly. Pull the upper lamp assembly
clear in order to access backup and rear turn signal lamp
bulbs.4. Replace the backup or rear turn signal lamp bulb.
Reinstall the appropriate bulb and socket assembly. Re-
install the three bulb and socket assemblies in the upper
lamp assembly. Reinstall the upper lamp assembly. Re-
place the access panel. Close the trunk.
MAINTAINING YOUR VEHICLE 217
7