2006 CHRYSLER PT CRUISER lock

Adding Washer Fluid
The fluid reservoir for the windshield washers and the
rear window washer (If Equipped) is shared. It is located
in the front of the engine compartment on the passenger
side and should be checked for fluid level at regular
intervals. Fill the reservoir with windshield washer sol-
vent (not radiator antifreeze) and operate the system for
a few seconds to flush out the residual water.
TILT STEERING COLUMN
To tilt the column, push down on the lever below the
multi-function control lever and move the steering wheel
up or down, as desired. Pull the lever back up to lock the
column firmly in place.
Tilt Steering Column Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187
3

WARNING!
Tilting the steering column while the vehicle is
moving is dangerous. Without a stable steering col-
umn, you could lose control of the vehicle and have
an accident. Adjust the column only while the ve-
hicle is stopped. Be sure it is locked before driving.
TRACTION CONTROL SWITCH — IF EQUIPPED
The traction control indicator, located in the
instrument cluster, will flash when the Traction
Control System (TCS ) is in use.
The TCS switch is located on the instrument panel below
the radio.
To turn the system OFF, press the TCS switch until the
traction control indicator in the instrument cluster lights
up.To turn the system back ON, press the switch a second
time until the traction control indicator turns OFF.
NOTE:The traction control indicator will illuminate
momentarily as a bulb check, each time the ignition
switch is turned ON. This will occur even if you used the
TCS switch to turn the system OFF.
Traction Control Switch
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
•To avoid tipping, lock the shelf securely in all
positions.
•Do not drive this vehicle with the liftgate open, or
use the shelf as a seat.
•Failure to follow these warnings could result in
serious or fatal injury.
Position 1 (Top)
Insert the front outboard corners of the shelf panel into
the top guides and slide forward. Press down on the back
of the shelf panel to lock it into place.
WARNING!
Do not load objects on the shelf in position 1 (top).
In an accident objects could strike occupants causing
serious or fatal injury.
Rear Shelf Panel Position 1
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Position 2 (Middle)
Insert the front outboard corners of the shelf panel into
the middle guides and slide forward. Press down on the
back of the shelf panel to lock it into place.WARNING!
Do not load objects over 100 lbs (45 kg) in position 2
(middle). Failure to follow this warning could cause
the shelf to collapse resulting in personal injury.
Position 3 (Floor)
Insert the front outboard corners of the shelf panel into
the bottom guides and slide forward.
NOTE:To carry items that may soil the carpeting, the
rear shelf panel may be inverted in position 2 or position
3.
Rear Shelf Panel Position 2
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209
3

Position 4 (Vertical)
Insert the front outboard corners of the shelf panel into
the vertical guides behind the rear seatbacks near the
floor and slide downward. Push the shelf panel forward
to lock it into place.WARNING!
When in the vertical position, the rear shelf panel
should not be used as a barrier for large objects in
the cargo area when the seatbacks folded down. In
an accident objects could strike the seatbacks or
occupants causing serious or fatal injury.
Position 5 (table)
With the liftgate open the rear shelf panel can be moved
rearward to act as a serving counter.
1. Install the front corners of the shelf panel into the top
rear guides. Press down on the shelf panel to lock it into
place.
Rear Shelf Panel Position 4
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

ROOF LUGGAGE RACK — IF EQUIPPED
The crossbars and siderails are designed to carry the
weight on vehicles equipped with a luggage rack. The
load must not exceed 150 lbs (68 kg), and should be
uniformly distributed over the luggage rack crossbars.
Use both adjustable crossbars assemblies to support the
load and distribute the load as evenly as possible.
To adjust the crossbars with latch style releases, release
the latches on the inboard side of the crossbar supports
on each side of the vehicle, then move the crossbars to the
desired position. Once the crossbar is in the desired
position, return both latches to the locked position.
To adjust the crossbars with botton style releases, depress
the button and slide the crossbar to the next locking
position. Alternate sides until the crossbars are posi-
tioned correctly for your cargo and the stanchions are
locked square to the slide rails.External racks do not increase the total load carrying
capacity of the vehicle. Be sure that the total occupant
and luggage load inside the vehicle, plus the load on the
luggage rack, do not exceed the rated vehicle capacity.
NOTE:When the luggage rack is not in use, place the
crossbars together at the rear of the vehicle. In this
position they are designed to improve the vehicle aero-
dynamics and reduce wind noise.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS

Instrument Panel Features.................218

Instrument Cluster—Base.................219

Instrument Cluster—Premium..............220

Instrument Cluster—Turbo................221

Instrument Cluster Descriptions............222

Electronic Vehicle Information Center (EVIC)–If
Equipped............................229
▫EVIC Functions.......................231
▫Compass/Temperature/Audio............231▫Average Fuel Economy.................232
▫Distance To Empty (DTE)...............232
▫Elapsed Time........................232
▫Personal Settings (Customer Programmable
Features)...........................232

Setting The Analog Clock.................238

Radio General Information................239
▫Radio Broadcast Signals.................239
▫Two Types Of Signals..................2394

12. Brake System Warning Light
This light monitors various brake functions,
including brake fluid level and parking brake
application. If the brake light turns on, it may
indicate that the parking brake is applied, there
is a low brake fluid level or there is a problem with the
anti-lock brake system.
The dual brake system provides a reserve braking capac-
ity in the event of a failure to a portion of the hydraulic
system. Failure of either half of the dual brake system is
indicated by the Brake Warning Light which will turn on
when the brake fluid level in the master cylinder has
dropped below a specified level.
The light will remain on until the cause is corrected.
NOTE:The light may flash momentarily during sharp
cornering maneuvers which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.If brake failure is indicated, immediate repair is neces-
sary.
WARNING!
Driving a vehicle with the brake light on is danger-
ous. Part of the brake system may have failed. It will
take longer to stop the vehicle. You could have an
accident. Have the vehicle checked immediately.
Vehicles equipped with Anti-Lock brakes (ABS), are also
equipped with Electronic Brake Force Distribution (EBD).
In the event of an EBD failure, the Brake Warning Light
will turn on along with the ABS Light. Immediate repair
to the ABS system is required.
The operation of the Brake Warning Light can be checked
by turning the ignition switch from the OFF position to
UNDERSTANDING YOUR INSTRUMENT PANEL 225
4