2006 CHRYSLER 300 LX light

EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states which have an I/M (Inspection and
Maintenance) requirement, this check verifies the
following: the MIL (Malfunction Indicator Light)
is functioning and is not on when the engine is running,
and that the OBD (On Board Diagnostic) system is ready
for testing.
Normally, the OBD system will be ready. The OBD
system maynotbe ready if your vehicle was recently
serviced, if you recently had a dead battery, or a battery
replacement. If the OBD system should be determined
not ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key actuated test
which you can use prior to going to the test station. To
check if your vehicle’s OBD system is ready, you must do
the following:
1. Insert your ignition key into the ignition switch.2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
4. As soon as you turn your key to the ON position, you
will see your MIL symbol come on as part of a normal
bulb check.
5. Approximately 15 seconds later, one of two things will
happen:
a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn off
the ignition key or start the engine. This means that
your vehicle’s OBD system isnot readyand you
shouldnotproceed to the I/M station.
b. The MIL will not flash at all and will remain fully
illuminated until you turn off the ignition key or
start the engine. This means that your vehicle’s OBD
system isreadyand you can proceed to the I/M
station.
296 MAINTAINING YOUR VEHICLE
ProCarManuals.com

underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MoparLock
Cylinder Lubricant or equivalent directly into the lock
cylinder.
Windshield Wiper Blades
The rubber edges of the wiper blades and the windshield
should be cleaned periodically with a sponge or soft cloth
and a mild nonabrasive cleaner. This will remove accu-
mulations of salt or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.
Avoid using the wiper blades to remove frost or ice from
the windshield. Keep the blade rubber out of contact with
petroleum products such as engine oil, gasoline, etc.
Windshield Washers/Headlight Washers—If
Equipped
The windshield washer and the headlight washer (if
equipped) share the same fluid reservoir. The reservoir is
located in the front of the engine compartment on the
passenger side of the vehicle. Be sure to check the fluid
level in the reservoir at regular intervals. Fill the reservoir
with windshield washer solvent (not radiator antifreeze)
and operate the system for a few seconds to flush out the
residual water.
Washer Fluid Reservoir
310 MAINTAINING YOUR VEHICLE
ProCarManuals.com

NOTE:Often, fluid such as oil, power steering fluid,
and brake fluid are used during assembly plant opera-
tions to facilitate the assembly of hoses to couplings.
Therefore, oil wetness at the hose-coupling area is not
necessarily an indication of leakage. Actual dripping of
hot fluid when systems are under pressure (during
vehicle operation), should be noted before a hose is
replaced based on leakage.
NOTE:Inspection of brake hoses should be performed
whenever the brake system is serviced and at every
engine oil change. Inspect hydraulic brake hoses for
surface cracking, scuffing, or worn spots. If there is any
evidence of cracking, scuffing, or worn spots, the hose
should be replaced immediately! Eventual deterioration
of the hose can take place resulting in a possibility of a
burst failure.
WARNING!
Worn brake hoses can burst and cause brake failure.
You could have an accident. If you see any signs of
cracking, scuffing, or worn spots, have the brake
hoses replaced immediately.
Brake Fluid Level Check
The fluid level in the master cylinder should be checked
when performing underhood services, or immediately if
the brake system warning light indicates system failure.
Clean the top of the master cylinder area before removing
the cap. Add fluid to bring the level up to the top of the
“FULL”mark on the side of the master cylinder reservoir.
Overfilling of fluid is not recommended because it may
cause leaking in the system.
Add enough fluid to bring the level up to the require-
ments described on the brake fluid reservoir. With disc
brakes, fluid level can be expected to fall as the brake
pads wear. However, low fluid level may be caused by a
leak and a checkup may be needed.
318 MAINTAINING YOUR VEHICLE
ProCarManuals.com

All Wheel Drive (AWD)—If Equipped
The all wheel drive system consists of a Transfer Case,
and Front Differential. The exterior surface of these
components should be inspected for evidence of fluid
leaks. Confirmed leaks should be repaired as soon as
possible.
The transfer case fill plug is located on the rear housing
near the output shaft. The level can be verified by the
service plug in the middle of the rear housing, even with
the bottom of the hole. The front differential fill plug is on
the outer cover near the halfshaft attachment. The level
can be verified by removing the plug and inspecting the
level. The level should be even with or slightly below the
bottom of the hole.
Fluid Changes
The fluid should be changed as follows:
Normal UsageNo Service Required
Severe Usage
Front Differential No Service Required
Transfer Case Refer to Maintenance
Schedule“B”Severe Usage is defined as:
1. More than 50% of vehicle operation in stop and go
traffic where vehicle is driven regularly for more than 45
minutes of continuous operation, such as in heavy city or
in construction zone traffic.
2. Police, taxi, limousine, commercial type operation, or
trailer towing where the vehicle driven regularly for
more than 45 minutes of continuous operation.
Front And Rear Wheel Bearings
Front and rear wheel bearings are permanently sealed.
No regular maintenance is required for these compo-
nents.
Appearance Care and Protection from Corrosion
Protection of Body and Paint from Corrosion
Vehicle body care requirements vary according to geo-
graphic locations and usage. Chemicals that make roads
passable in snow and ice, and those that are sprayed on
trees and road surfaces during other seasons, are highly
corrosive to the metal in your vehicle. Outside parking,
which exposes your vehicle to airborne contaminants,
road surfaces on which the vehicle is operated, extreme
MAINTAINING YOUR VEHICLE 321
7
ProCarManuals.com

Front Power Distribution Center Fuses
Cavity Fuse Circuits
1 20 Amp
YellowLeft High Intensity Discharge
Headlight - if equipped
2 20 Amp
YellowRight High Intensity Discharge
Headlight - if equipped
3 15 Amp
BlueAdjustable Pedals - if
equipped
4 20 Amp
YellowAC Clutch/Horn
5 20 Amp
YellowHeadlight Washer - If
Equipped
6 15 Amp
BlueFront Control Module (FCM)
7 20 Amp
YellowFog Lights
8 15 Amp
BlueLights–License, Park, Side
Marker, Stop, Turn
9 15 Amp
BlueFront Control Module (FCM)
10 5 Amp
OrangePowertrain Control Module
(PCM)/Starter
Cavity Fuse Circuits
11 20 Amp
YellowAuto Shutdown/Powertrain
Control Module (PCM)
12——
13——
14 25 Amp
ClearPowertrain Control Module
(PCM)
15 25 Amp
ClearInjectors, Ignition Coils
16——
17 30 Amp
PinkAntilock Brakes System (ABS)
Valves/Powertrain Control
Module (PCM)
18 30 Amp
PinkWindshield Wiper/Washer
19 50 Amp
RedRadiator Fan
20 20 Amp
BlueStarter
21 50 Amp
RedAntilock Brakes System (ABS)
Pump Motor
MAINTAINING YOUR VEHICLE 327
7
ProCarManuals.com

Cavity Fuse Circuits
22 40 Amp
GreenAC Clutch/Radiator Fan High
—Low
23 50 Amp
RedHigh Intensity Lighting - if
equipped
24 60 Amp
YellowRadiator Fan - AWD
25 30 Amp
PinkFront Control Module (FCM)
26 20 Amp
BlueTransmission - RLE
27 30 Amp
PinkFront Control Module (FCM)Rear Power Distribution Center
There is also a power distribution center located in the
trunk under the spare tire access panel. This center
contains fuses and relays.
Opening The Access Panel
328 MAINTAINING YOUR VEHICLE
ProCarManuals.com

Cavity Fuse Circuits
18 20 Amp
YellowSelectable Power Outlet
19 10 Amp
RedStop Lights
20——
21——
22——
23——
24——
25——
26——
27 10 Amp
RedAirbag/Occupant Classifica-
tion Module
28 10 Amp
RedCurtain Airbag - if equipped
29 5 Amp
OrangeAntilock Brakes Module/
Cluster/Front Control Module
(FCM)/Powertrain Control
Module (PCM)/Sentry Key
Remote Keyless Entry/Stop
LightsCavity Fuse Circuits
30 10 Amp
RedDoor Modules/Power Mirrors
- if equipped/Steering Control
Module
31——
32——
33——
34——
35 5 Amp
OrangeAmplifier - if equipped/
Antenna/Ignition Delay/
Overhead Console - if
equipped/Passenger Door
Lock & Express Power Win-
dow Switch - if equipped/
Power Mirrors - if equipped/
Rain Sensor - if equipped/
Rear Defrost
36 20 Amp
YellowHands Free Phone - if
equipped/Media System
Monitor DVD - if equipped/
Radio/Satellite Receiver - if
equipped
MAINTAINING YOUR VEHICLE 331
7
ProCarManuals.com

Cavity Fuse Circuits
37 15 Amp
BlueTransmission - NAG1
38 5 Amp
OrangeAnalog Clock/Cargo Light/
Overhead Console - if
equipped
39 10 Amp
RedHeated Mirrors - if equipped
40 5 Amp
OrangeHeated Seats - if equipped/
Inside Rearview Mirror/
Manual Temperature Control
(early build) - if equipped
41 10 Amp
RedAC Heater Control (except
early build MTC)/Park Assist
- if equipped/Tire Pressure
Monitoring - if equipped
42 30 Amp
PinkFront Blower Motor
43 30 Amp
PinkAmplifier - if equipped/
Antenna/Rear Defrost
44 20 Amp
BlueAmplifier - if equipped/Front
Control Module (FCM)/
Sunroof - if equippedVEHICLE STORAGE
If you are leaving your vehicle dormant for more than 21
days you may want to take steps to protect your battery.
You may:
•Disconnect the negative cable from the battery.
•Anytime you store your vehicle, or keep it out of
service (i.e. vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
insure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
332 MAINTAINING YOUR VEHICLE
ProCarManuals.com