2006 CHEVROLET SSR remove seats

Windscreen
A. Windscreen
B. Bevelled Notch in Carpeted Seatback Bumper
C. Protective Cap on Carpeted Seatback Bumper
The vehicle may have a windscreen (A) installed to the
rear of each seat to lessen wind noise while the
convertible roof is retracted. The convertible roof can be
opened or closed with the windscreen installed. The
vehicle must have the correct seatback bumpers
to install the windscreen.The correct seatback bumpers have a bevelled
notch (B) above the seat’s inboard protective cap (C).
The notch allows the bumper to fit over the windscreen
bracket which mounts to the inboard mounting studs.
Install the windscreen by following these steps:
1. Before installing the windscreen, the convertible top
must be fully retracted and the seats moved forward.
2. Remove the windscreen from its protective bag.
3. Locate the carpeted seatback bumper behind
each seat.
4. Remove protective caps from the bumpers.
5. Loosen the four seatback bumper nuts from
each seat. It is not necessary to remove the
bumpers completely.
6. With the seatback bumpers loosened, slide the
windscreen mounting brackets behind the
seatback bumpers. The angled portion of the
mounting brackets should rest tightly into the bevels
of the seatback bumpers.
7. Tighten the bumper nuts and reinstall the protective
molding caps.
When not using the windscreen, store it in its protective
bag. To remove the windscreen, reverse the steps
listed previously. Rear View of Seatback
2-46

If the cargo area is closed and the roof tonneau does
not raise or lower, check to see if a fuse is blown.
SeeFuses and Circuit Breakers on page 5-86for
more information.
Contact your GM dealer if the roof tonneau still does not
raise or lower after replacing the fuse.
The roof tonneau can manually be raised or lowered in
the event of a power loss. SeeRaising the Convertible
Top on page 2-48for instructions.
Raising the Convertible Top
Notice:If you operate the convertible top switch
continuously while the ignition is in ACCESSORY,
the battery will drain and you might not be able
to start your vehicle. Do not use the convertible top
switch for extended periods of time when the
ignition is in ACCESSORY.
The ignition must be in RUN or ACCESSORY, your foot
must be on the brake, and the vehicle must be
stopped in order to raise the convertible top.
b(Top Closed):Press and hold this symbol on
the convertible top switch located on the center console
switchbank to close the convertible top. Two chimes
will sound when the top is fully closed.A “Roof Cycle Timeout” message will display on the
Driver Information Center (DIC) and the convertible top
will stop moving when the programmed time limit is
exceeded for the raised position. See “Roof Cycle
Timeout” underDIC Warnings and Messages on
page 3-45.
If the convertible top cannot be raised by using the
convertible top switch, the fuse may need to be
replaced. SeeFuses and Circuit Breakers on page 5-86
for more information.
If the convertible top still cannot be lowered or raised,
contact your GM dealer.
The roof tonneau and convertible top can be raised in
the event of a power loss. Two people are needed to lift
the roof tonneau and convertible top when using the
following procedure.
1. Turn the ignition to OFF.
2. Open both doors.
3. In the area behind the seats, locate the two sets of
cables behind the carpet flaps. The cables on the
driver’s side are located behind the tire inflator
kit. The tire inflator kit must be removed to access
the cables. SeeTire Inator Kit on page 5-68
for instructions on how to remove the tire inflator kit.
2-48

0(Defrost):This mode directs most of the air to the
windshield. When you select this mode, the system
runs the air-conditioning compressor unless the outside
temperature is at or below freezing. Recirculation is
not available in this mode.
1(Maximum Defrost):This mode directs most of
the air to the windshield. The rear window defogger and
heated outside mirrors will turn on, and the fan speed
will be at the highest setting (5). The temperature will be
at the hottest setting also. Recirculation is not available
in this mode.
If this mode was selected when you turn your vehicle
off, the warmest temperature and highest fan speed will
be restored when the vehicle is started, regardless of
the temperature and fan setting.
Do not drive the vehicle until all the windows are clear.
Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog from the rear window.
The rear window defogger will only work when the
ignition is on.
=(Rear):Press this button on the mode knob to turn
the rear window defogger on or off. An indicator light
on the button will come on to let you know that the rear
window defogger is activated.
When the rear defogger button is pressed, the outside
heated mirrors will warm to help clear any fog or
frost from the surface of the mirrors.
Notice:Do not use a razor blade or sharp object to
clear the inside rear window. Do not adhere
anything to the defogger grid lines in the rear glass.
These actions may damage the rear defogger.
Repairs would not be covered by your warranty.
Outlet Adjustment
Use the levers located in the center of each outlet to
change the direction of the airflow.
Operation Tips
•
Clear away any ice, snow or leaves from the air
inlets at the base of the windshield that may
block the flow of air into your vehicle.
•Use of non-GM approved hood deflectors may
adversely affect the performance of the system.
•Keep the path under the front seats clear of
objects to help circulate the air inside of your
vehicle more effectively.
3-23

Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure you
replace a bad fuse with a new one of the identical
size and rating.
If you ever have a problem on the road and don’t have
a spare fuse, you can borrow one that has the same
amperage. Just pick some feature of your vehicle
that you can get along without — like the radio or
cigarette lighter — and use its fuse, if it is the correct
amperage. Replace it as soon as you can.
Floor Console Fuse Block
The floor console fuse
block is located on the
console between the
two seats, on the
passenger’s side.To remove the fuse block cover and access the fuses,
do the following:
1. Move the passenger’s seat all the way forward and
tilt the seatback forward. SeePower Seats on
page 1-2andSeatback Latches on page 1-6for
more information.
2. Pull the handle on the fuse block cover toward you
and then slide it to the side. You will then be able
to remove the cover completely.
3. To reinstall the cover, slide it to the side until it is
lined up with the access hole. Then, push on the
fuse panel cover until it latches into place.
5-87