2006 CHEVROLET OPTRA 5 light

Fog Lamp Light............................................3-41
Cruise Control Light......................................3-41
Highbeam On Light.......................................3-41
Daytime Running Lamps (DRL) Indicator Light.....3-41
Door Ajar Light.............................................3-42
Trunk Ajar Light............................................3-42
Fuel Gage...................................................3-42
Low Fuel Warning Light.................................3-43Audio System(s).............................................3-44
Radio with CD (Single Display, Base Level)......3-45
Radio with CD (Single Display, MP3)...............3-49
Radio with CD (Double Display, MP3/WMA).....3-57
Radio with Six-Disc CD (Double Display,
MP3/WMA) ...............................................3-65
Audio Steering Wheel Controls.......................3-73
Radio Reception...........................................3-74
Care of Your CDs.........................................3-75
Care of the CD Player...................................3-75
Integrated Windshield Antenna........................3-75
Section 3 Instrument Panel
3-2

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on page 3-25.
B. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 3-27.
C. Hazard Warning Flashers Button. SeeHazard
Warning Flashers on page 3-8.
D. Digital Clock. SeeClock on page 3-21.
E. Audio System. SeeAudio System(s) on page 3-44.
F. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 3-18.
G. Hood Release. SeeHood Release on page 5-10.
H. Exterior Lamps Control. SeeExterior Lamps
on page 3-16.I. Horn. SeeHorn on page 3-8.
J. Cruise Control. SeeCruise Control on page 3-13.
K. Windshield Wiper Control. SeeWindshield Wipers on
page 3-11.
L. Climate Control System. SeeClimate Control
System on page 3-22.
M. Ashtray. SeeAshtray(s) and Cigarette Lighter on
page 3-20.
N. Cigarette Lighter. SeeAshtray(s) and Cigarette
Lighter on page 3-20.
O. Glove Box. SeeGlove Box on page 2-34.
3-5

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on page 3-25.
B. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 3-27.
C. Hazard Warning Flashers Button. SeeHazard
Warning Flashers on page 3-8.
D. Digital Clock. SeeClock on page 3-21.
E. Audio System. SeeAudio System(s) on page 3-44.
F. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 3-18.
G. Hood Release. SeeHood Release on page 5-10.
H. Exterior Lamps Control. SeeExterior Lamps
on page 3-16.
I. Audio Steering Wheel Controls (If Equipped). See
Audio Steering Wheel Controls on page 3-73.J. Horn. SeeHorn on page 3-8.
K. Cruise Control Buttons. SeeCruise Control on
page 3-13.
L. Windshield Wiper Control. SeeWindshield Wipers
on page 3-11.
M. Climate Control System. SeeClimate Control
System on page 3-22.
N. Ashtray. SeeAshtray(s) and Cigarette Lighter on
page 3-20.
O. Cigarette Lighter. SeeAshtray(s) and Cigarette
Lighter on page 3-20.
P. Glove Box. SeeGlove Box on page 2-34.
3-7

Tilt Wheel
Your vehicle has a tilt wheel which allows you to adjust
the steering wheel before you drive. You can raise it
to the highest level to give your legs more room when
you exit and enter the vehicle.
The lever that allows you to tilt the steering wheel is
located under the steering column.
To tilt the steering wheel, hold the wheel and push the
lever away from you. Then, move the wheel to a
comfortable position and pull the lever toward you to
lock the wheel in place.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
•Turn and Lane-Change Signals. SeeTurn and
Lane-Change Signals on page 3-10.
•Headlamp High/Low-Beam Changer. SeeHeadlamp
High/Low-Beam Changer on page 3-10.
•Flash-to-Pass. SeeFlash-to-Pass on page 3-10.
•Exterior Light Control. SeeExterior Lamps on
page 3-16.
•Fog Lamps, if equipped. SeeFog Lamps on
page 3-17.
Uplevel shown, Base similar
3-9

Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.
To signal a lane change, just raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
your lane change. The lever will return by itself when you
release it.
As you signal a turn or a lane change, if the arrows flash
rapidly, a signal bulb may be burned out and other drivers
will not see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you signal
a turn, check for burned-out bulbs. If the arrow still does
not work, check the fuse. SeeFuses and Circuit Breakers
on page 5-82.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high
beam, push the turn signal/multifunction lever away
from you.
When the high beams are
on, a light on the
instrument panel cluster
also will be on if the
ignition is turned to ON.
To change the headlamps from high beam to low beam,
pull the turn signal lever toward you.
Flash-to-Pass
This feature lets you use your high-beam headlamps to
signal a driver in front of you that you want to pass.
To use it, pull the turn signal/multifunction lever toward
you until the high-beam headlamps come on, then
release the lever to turn them off.
3-10

Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you
are not using cruise, you might hit a button
and go into cruise when you do not want to.
You could be startled and even lose control.
Keep the cruise control switch off until you
want to use cruise control.The cruise control pad is located on the right side of the
steering wheel.
1. Press the ON/OFF button to turn cruise control on.
2. Accelerate to the speed you want.
3. Press the SET button and release it. An indicator
light on the instrument panel cluster will come on
to show you that the cruise control is on. SeeCruise
Control Light on page 3-41.
4. Take your foot off the accelerator pedal.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake pedal, or the clutch
pedal if you have a manual transaxle. This, of course,
shuts off the cruise control. But you do not need to reset
it. Once you are going about 24 mph (39 km/h) or
more, you can briefly press the RESUME button.
You will go right back up to your chosen speed and
stay there.
If you hold in the RESUME button longer, the vehicle
will keep going faster until you release the button
or apply the brake pedal. So unless you want to go
faster, do not hold in the RESUME button.
3-14

Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed.
•Use the accelerator pedal to get to a higher speed.
Press the SET button, then release the button and
the accelerator pedal. You will now cruise at the
higher speed.
•Press the RESUME button. Hold it there until you
get up to the speed you want, and then release
the button. To increase your speed in very
small amounts, briefly press the RESUME button
and then release it. Each time you do this, your
vehicle will go about 1 mph (1.6 km/h) faster.
The accelerate feature will only work after you turn on
the cruise control by pressing the SET button.
Reducing Speed While Using Cruise
Control
There are two ways to reduce your speed while using
cruise control:
•Press the SET button until you reach the lower
speed you want, then release it.
•To slow down in very small amounts, briefly press
the SET button. Each time you do this, you will go
about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, your vehicle will
slow down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the
hills. When going up steep hills, you may have to step
on the accelerator pedal to maintain your speed.
When going downhill, you may have to brake or shift to
a lower gear to keep your speed down. Of course,
applying the brake pedal takes you out of cruise control.
Many drivers find this to be too much trouble and do
not use cruise control on steep hills.
Ending Cruise Control
There are two ways to turn off the cruise control:
•Step lightly on the brake pedal, or press the clutch
pedal, if you have a manual transaxle.
•Press the ON OFF button on the cruise control pad.
Erasing Speed Memory
When you turn off the cruise control or the ignition, your
cruise control set speed memory is erased.
3-15

Exterior Lamps
The lever on the left side of the steering column
operates the exterior lamps.
The exterior lamp band has three positions:
2(Headlamps):Turn the band to this position to turn
on the headlamps, together with the following:
•Taillamps
•License Plate Lamp
•Instrument Panel Lights
The headlamps will turn off automatically when the
ignition switch is turned to LOCK or ACC.
;(Parking Lamps):Turn the band to this position to
turn on the parking lamps, together instrument panel
lights, taillamps, and license plate lamp.
OFF:Turn the band to this position to turn all lamps off
except the Daytime Running Lamps (DRL).
Headlamps on Reminder
If you open the driver’s door with the ignition turned to
LOCK or ACC while leaving the lamps on, you will
hear a warning chime.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the
day. DRL can be helpful in many different driving
conditions, but they can be especially helpful in the short
periods after dawn and before sunset. Uplevel shown, Base similar
3-16