2006 CADILLAC ESCALADE ESV remove

I(Seatback Only):This can only be used for the
heat feature. Press this button to heat the seatback and
cycle through the heat settings of high, medium, low
and off. Red indicator lights will glow for each heat
setting chosen: three lights for high, two for medium and
one for low. A light in the button will also glow to
indicate the seatback heat is on.
J(Entire Seat):Press this button to heat or cool the
entire seat and cycle through the settings of high,
medium, low and off. Red (for heat) or blue (for cool)
indicator lights will glow for each setting chosen:
three lights for high, two for medium and one for low.
60/40 Split Bench Seat
(Second Row)
If your vehicle has a 60/40 split bench, the seats can be
ipped and folded for additional cargo space.
Flip and Fold Feature
To ip and fold the seat, do the following:
1. Make sure that there is nothing under or in front of
the seat.
2. Make sure that the headrests are completely
lowered or removed.On regular models, the rear seatbacks may be
equipped with rearward folding headrests. When the
seatback is being folded forward, the head rest
will automatically fold rearward.
On extended models, the headrests need to be
removed and stored. To do this, push the button at
the base of the head rest, and pull the head rest
out from the seatback. Slide the head rest pins into
the holes on the top of the seat cushion.
3. Pull up on the strap
loop located at the rear
of the seat cushion
and ip the seat
cushion forward.
1-12

50/50 Split Bench Seat (Third Row)
If your vehicle has a 50/50 split bench seat, the
seatback(s) can be folded and the entire seat(s) can be
tilted, or removed from the vehicle.
Folding the Seatback(s)
To fold the seatback, do the following:
Pull up on the release
lever labeled 1, located on
the rear of the seatback,
and push the seatback
forward.
Unfolding the Seatback(s)
To return the seatback to the upright position, do the
following:
1. Pull up on the release
lever labeled 1, located
on the rear of the
seatback. Then pull up
on either the seatback
or the assist strap,
located on the outboard
side of the seat, until
the seatback locks into
the upright position.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatback to be sure it is
locked.
2. Push and pull on the seatback to make sure it is
locked.
1-15

Removing the 50/50 Split Bench
Seat(s)
To remove the seat, do the following:
1. Open the liftgate to access the controls for the
50/50 seat(s) and enter the rear of the vehicle.
2. Fold the seatback forward using the instructions
listed under “Folding the Seatbacks” previously.
The seat cannot be removed unless the seatback is
folded.
3. Unlatch the rear of the
seat from the oor by
pulling up on the
release lever labeled 2,
located next to the
carrying handle at the
rear of the seat.
4. Lift the rear of the seat up from the oor.5. Squeeze the release lever to release the seat from
the oor, while pulling the seat out.
6. While holding the rear of the seat up, roll the seat
out of the vehicle.
1-18

{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatback to be sure it is
locked.
6. Push and pull on the seatback to make sure it is
locked.
Bench Seat (Third Row)
If your vehicle has a full bench seat, the seatback can
be folded, and the entire seat can be tilted, or removed
from the vehicle.
Folding the Seatback
To fold the seatback, do the following:
Pull up on the release
lever labeled 1, located on
the rear of the seatback,
and push the seatback
forward.
1-20

6. Pull up on the release lever labeled 1, located on
the rear of the seatback, and then pull up on the
seatback until it locks into the upright position.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatback to be sure it is
locked.
7. Push and pull on the seatback to make sure it is
locked.
Removing the Bench Seat
To remove the seat, do the following:
1. Open the liftgate to access the controls for the
bench seat and enter the rear of the vehicle.
2. Fold the seatback forward using the instructions
listed under “Folding the Seatback” previously.
The seat cannot be removed unless the seatback
is folded.3. Pull up on the release
lever labeled 2, located
at the rear of the
seat, to unlatch the
rear of the seat
from the oor.
4. Lift the rear of the seat up from the oor.
5. Pull on the release
strap, located in the
lower center of
the seat, to release the
seat from the oor
and pull the seat out.
Use one hand to
pull the release strap
and the other on
the handle to pull the
seat out.
6. While holding the rear of the seat up, roll the seat
out of the vehicle.
1-23

{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatback to be sure it is
locked.
Pull up on the lever without applying pressure to the
seatback and the seatback will return to the upright
position. Push and pull on the seatback to make sure it
is locked in place.
Flip and Fold Feature
The seat cushions on the bucket seats can be ipped
forward and the seatbacks can be folded forward to give
you more cargo space.
To ip and fold the bucket seats, do the following:
1. Pull up on the strap
loop located at the rear
of the seat cushion
and pull the seat
cushion up and fold it
forward.
2. On the extended models, remove the headrest and
store it on the top of the seat cushion.
1-26

Rear Safety Belt Comfort Guides
Rear shoulder belt comfort guides may provide added
safety belt comfort for older children who have outgrown
booster seats and for some adults. When installed on
a shoulder belt, the comfort guide positions the belt
away from the neck and head.
There is one guide for each passenger position with a
lap-shoulder belt in the rear seats. Here is how to install
a comfort guide and use the safety belt:
1. For the second row, remove the guide from its
storage clip on the trim panel near the side of
the seatback or from the side of the center seat.Second Row Seat
1-46

For the third row, remove the guide from its storage
clip on the side of the seatback.2. Place the guide over the belt and insert the
two edges of the belt into the slots of the guide.
3. Be sure that the belt is not twisted and it lies at.
The guide must be on top of the belt. Third Row Seat
1-47