2006 CADILLAC DTS tires
[x] Cancel search: tiresPage 358 of 450
In ation - Tire Pressure
Tires need the correct amount of air pressure to
operate effectively.
Notice:Do not let anyone tell you that
under-in ation or over-in ation is all right. It is not.
If your tires do not have enough air (under-in ation),
you can get the following:
Too much exing
Too much heat
Tire overloading
Premature or irregular wear
Poor handling
Reduced fuel economy
If your tires have too much air (over-in ation), you
can get the following:
Unusual wear
Poor handling
Rough ride
Needless damage from road hazardsA Tire and Loading Information label is attached to the
vehicle’s center pillar, below the driver’s door latch.
This label lists your vehicle’s original equipment
tires and shows the correct in ation pressures for your
tires when they are cold. The recommended cold
tire in ation pressure, shown on the label, is the
minimum amount of air pressure needed to support your
vehicle’s maximum load carrying capacity.
For additional information regarding how much weight
your vehicle can carry, and an example of the tire
and loading information label, seeLoading Your Vehicle
on page 4-31. How you load your vehicle affects the
vehicle handling and ride comfort, never load your
vehicle with more weight than it was designed to carry.
When to Check
Check your tires once a month or more. Do not forget to
check the spare tire. If your vehicle has a compact
spare tire, it should be at 60 psi (420 kPa). For additional
information seeSpare Tire on page 5-82.
5-56
Page 359 of 450
How to Check
Use a good quality pocket-type gage to check tire
pressure. You cannot tell if your tires are properly in ated
simply by looking at them. Radial tires may look properly
in ated even when they are under-in ated. Check the
tire’s in ation pressure when the tires are cold. Cold
means your vehicle has been sitting for at least three
hours or driven no more than 1 mile (1.6 km).
Remove the valve cap from the tire valve stem.
Press the tire gage rmly onto the valve to get a
pressure measurement. If the cold tire in ation
pressure matches the recommended pressure on the
Tire and Loading Information label, no further
adjustment is necessary. If the in ation pressure is
low, add air until you reach the recommended amount.If you over ll the tire, release air by pushing on the
metal stem in the center of the tire valve. Re-check the
tire pressure with the tire gage.
Be sure to put the valve caps back on the valve
stems. They help prevent leaks by keeping out dirt
and moisture.
Your vehicle has a Tire Pressure Monitor (TPM) that
sends tire pressure information to the Driver Information
Center (DIC). Using the DIC control buttons, the
driver is able to check tire pressure levels in all
four road tires. SeeTire Pressure Monitor System on
page 5-59andDIC Controls and Displays on page 3-72
for additional information.
5-57
Page 360 of 450
High Speed Operation
{CAUTION:
Driving at high speeds, 100 mph (160 km/h) or
higher, puts an additional strain on tires.
Sustained high-speed driving causes
excessive heat build up and can cause sudden
tire failure. You could have a crash and you or
others could be killed. Some high-speed rated
tires require in ation pressure adjustment for
high speed operation. When speed limits and
road conditions are such that a vehicle can be
driven at high speeds, make sure the tires are
rated for high speed operation, in excellent
condition, and set to the correct cold tire
in ation pressure for the vehicle load.If your vehicle has P235/55R17 or P245/50R18 size
tires, and you will be driving at speeds of 100 mph
(160 km/h) or higher, where it is legal, set the cold
in ation pressure to the maximum in ation pressure
shown on the tire sidewall, or 38 psi (265 kPa),
whichever is lower. See the example following.
Example:
You will nd the maximum load and in ation pressure
molded on the tire’s sidewall, in small letters, near
the rim ange. It will read something like this: Maximum
load 690 kg (1521 lbs) 300 kPa (44 psi) Max. Press.
For this example, you would set the in ation pressure for
high-speed driving at 38 psi (265 kPa).
When you end this high-speed driving, return the tires to
the cold in ation pressure shown on the Tire and
Loading Information label. SeeLoading Your Vehicle on
page 4-31.
5-58
Page 361 of 450
Professional Vehicle
The proper in ation of the tires on your professional
vehicle depends on the type of tires on it.
If your vehicle has P235/60R17 size tires, the cold
in ation pressure is 41 psi (284 kPa).
If your vehicle has LT235/60R17E size tires, the cold
in ation pressure depends on the vehicle mass and
should be determined by the vehicle coach-builder.
A tire and loading information label provided by the
nal stage manufacturer should be attached to the
B-pillar on the driver’s side of the vehicle. If the nal
stage manufacturer’s label is not present, the
coach-builder should be consulted. Do not use the
tire pressures indicated on the General Motors label.
These tire pressures are for the incomplete vehicle
and are not the correct tire pressures for the
completed professional vehicle.
Operation at in ation pressures below this
recommendation may cause your tires to become
overloaded.
Tire Pressure Monitor System
The Tire Pressure Monitor System (TPMS) is designed
to monitor the amount of pressure in your vehicle’s
tires using radio and sensor technology. A TPMS
sensor, mounted onto the vehicle’s full-size tire and
wheel assembly, transmits tire pressure readings to a
receiver located in the vehicle. The compact spare
tire and wheel does not have a TPMS sensor.
Tire pressure status and tire pressure warnings are
shown on the Driver Information Center (DIC) display.
For additional information and details about the DIC
operation and displays seeDIC Controls and Displays
on page 3-72andDIC Warnings and Messages on
page 3-76.
If a low tire pressure condition is detected, the TPMS
will display the CHECK TIRE PRESSURE warning
message on the DIC and, at the same time, illuminate
the low tire pressure warning symbol, on the instrument
panel cluster.
You may notice, during cooler weather conditions, that
the low tire pressure warning symbol and the CHECK
TIRE PRESSURE message will display when the vehicle
is rst started and then turn off as you start to drive
the vehicle. This could be an early indicator that the tire
pressures are getting low and need to be checked
and in ated to the proper pressure.
5-59
Page 362 of 450
Each tire, including the spare (if provided), should be
checked monthly when cold and in ated to the in ation
pressure recommended by the vehicle manufacturer
on the vehicle placard or tire in ation pressure label.
(If your vehicle has tires of a different size than the size
indicated on the vehicle placard or tire in ation
pressure label, you should determine the proper
tire in ation pressure for those tires.)
As an added safety
feature, your vehicle has
been equipped with a
tire pressure monitoring
system (TPMS) that
illuminates a low tire
pressure telltale when one
or more of your tires is
signi cantly under-in ated.
Accordingly, when the low tire pressure telltale
illuminates, you should stop and check your tires as
soon as possible, and in ate them to the proper
pressure. Driving on a signi cantly under-in ated tire
causes the tire to overheat and can lead to tire failure.
Under-in ation also reduces fuel efficiency and tire
tread life, and may affect the vehicle’s handling
and stopping ability.Please note that the TPMS is not a substitute for proper
tire maintenance, and it is the driver’s responsibility to
maintain correct tire pressure, even if under-in ation has
not reached the level to trigger illumination of the
TPMS low tire pressure telltale.
The CHECK TIRE PRESSURE warning message and
low tire pressure light (telltale) will appear at each
ignition cycle until the tires are in ated to the correct
in ation pressure.
The Tire and Loading Information Label shows the size
of your vehicle’s original tires and their recommended
cold in ation pressures. SeeLoading Your Vehicle
on page 4-31, for the location of the tire and loading
information label. Also seeIn ation - Tire Pressure
on page 5-56.
Your vehicle’s TPMS can alert you about a low tire
pressure condition but it does not replace normal tire
maintenance. SeeTire Inspection and Rotation on
page 5-63andTires on page 5-49.
Notice:Do not use a tire sealant if your vehicle has
Tire Pressure Monitors. The liquid sealant can
damage the tire pressure monitor sensors.
5-60
Page 363 of 450
Resetting the TPMS Sensor
Identi cation Codes
Each TPMS sensor has a unique identi cation code.
Any time you replace one or more of the TPMS sensors,
rotate the vehicle’s tires, or install a full-size spare
that has a TPMS sensor, the sensor’s identi cation
codes will need to be matched to the new tire/wheel
position. Each tire/wheel position is matched to
the TPMS sensor using a TPMS diagnostic tool. See
your GM dealer for service.
The TPMS sensors may also be matched to each
tire/wheel position by increasing or decreasing the tire’s
air pressure. When increasing the tire’s air pressure,
do not exceed the maximum tire pressure indicated on
the tire’s sidewall.
You will have two minutes to match the rst tire/wheel
position, and ve minutes overall, to match all
four tire/wheel positions. If it takes longer than
two minutes, to match the rst tire and wheel, or
more than ve minutes to match all four tire and wheel
positions the matching process stops and you will
need to start over.The TPMS matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to RUN with the engine off.
3. Press the Driver Information Center (DIC) vehicle
information button until the RELEARN TIRE
POSITIONS displays.
4. Press the set/reset button to allow the system to
learn the tire positions. The horn will sound twice
to indicate that the TPMS is ready, and then
the message TIRE LEARNING ACTIVE will display.
The sensor matching process can begin.
5. Start with the driver’s side front tire.
6. Remove the valve cap from the valve stem.
Activate the TPMS sensor by increasing or
decreasing the tire’s air pressure for ve seconds,
or until a horn chirp sounds. The horn chirp,
which may take up to 30 seconds, con rms that the
sensor identi cation code has been matched to
this tire position. To decrease the tire’s air-pressure
use the pointed end of the valve cap, a pencil-style
air pressure gage or a key.
5-61
Page 364 of 450
7. Proceed to the passenger’s side front tire, and
repeat the procedure in Step 6.
8. Proceed to the passenger’s side rear tire, and
repeat the procedure in Step 6.
9. Proceed to the driver’s side rear tire, and repeat the
procedure in Step 6.
10. When the re-learning is complete, the horn will
sound and the TIRE LEARNING ACTIVE message
will clear from the DIC display. Exit the matching
process by turning the ignition switch to OFF.
11. Set all four tires to the recommended air pressure
level as indicated on the tire and loading information
label.
12. Put the valve caps back on the valve stems.
The compact spare tire does not have a TPMS sensor.
If you replace one of the road tires with the compact
spare, the SERVICE TIRE MONITOR SYSTEM
message will be displayed on the DIC screen. This
message should go off once you re-install the road tire
containing the TPMS sensor. The SERVICE TIRE
MONITOR SYSTEM message is also displayed when
a part of the TPMS is not working properly.One or more missing or inoperable TPMS sensors will
cause the service tire monitor message to be displayed.
See your GM dealer for service if all the TPMS
sensors are installed and the error message comes on
and stays on.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modi cations to this system by other than
an authorized service facility could void authorization to
use this equipment.
5-62
Page 365 of 450
Tire Inspection and Rotation
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km).
Any time you notice unusual wear, rotate your tires as
soon as possible and check wheel alignment. Also
check for damaged tires or wheels. SeeWhen It Is Time
for New Tires on page 5-64andWheel Replacement
on page 5-69for more information.
The purpose of regular rotation is to achieve more
uniform wear for all tires on the vehicle. The rst rotation
is the most important. SeeScheduled Maintenance
on page 6-4.
If your vehicle has a compact spare tire, it should not be
included in the tire rotation process. Use the four-tire
rotation pattern shown.A ve-tire rotation pattern may be used for your
professional vehicle, if it has a full-size spare tire and
wheel assembly that matches the original equipment
tires and wheels in size, type and brand. The correct
ve-tire rotation pattern is shown.
After the tires have been rotated, adjust the front and
rear in ation pressures as shown on the Tire and
Loading Information label. SeeLoading Your Vehicle on
page 4-31.
Vehicles that have the Tire Pressure Monitor System
(TPMS) will need to have the sensors reset after a tire
rotation is performed. SeeTire Pressure Monitor
System on page 5-59. Four-Tire Rotation Pattern
Five-Tire Rotation Pattern
5-63