2006 BMW MOTORRAD K 1200 S service

Motorcycle data/dealership detailsMotorcycle dataModel
Vehicle identification number
Colour code
Date of first registration
Registration number
Dealership detailsPerson to contact in Service depart-
ment
Ms/Mr
Phone number
Dealership address/phone number
(company stamp)

Parking your
motorcycle . . . ........... 69
Refuelling . . . . . .......... 71
Tyre pressure control
RDC
OE
.................. 72
Brake system, general . . . 73
Brake system with BMW
Motorrad Integral ABS . . . 74
6 Accessories .......... 79
General instructions . . . . . 80
Power socket . .......... 80
Luggage . . . . . . .......... 81
CaseOA
................. 81
Breakdown assistance
kit
OA
.................... 85
7 Maintenance . . . . . . . . . 87
General instructions . . . . . 88
Toolkit . ................. 88
Engine oil . . . . . .......... 89
Brake system, general . . . 91
Brake pads . . . . .......... 92
Brake fluid . . . . .......... 94
Clutch . ................. 96
Tyres . . ................. 97
Rims . . . ................. 97 Wheels .
................. 97
Front-wheel stand . ..... 105
Rear-wheel stand . . ..... 107
Bulbs . . ................ 108
Jump start . . . . ......... 118
Battery . ................ 119
8 Care . ................ 125
Care products . ......... 126
Washing motorcycle . . . . 126
Cleaning easily damaged
components . . . ......... 127
Paint care . . . . . ......... 128
Protective wax
coating ................ 128
Laying up the
motorcycle . . . . ......... 128
Restoring motorcycle to
use .................... 129
9 Technical data . . ..... 131
Troubleshooting
chart . . . ................ 132
Threaded fasteners ..... 133
Engine . ................ 134
Riding specifications . . . . 137
Clutch . ................ 137 Transmission . .
......... 137
Final drive . . . . . ......... 139
Running gear . . ......... 139
Brakes . ................ 140
Wheels and tyres . . ..... 140
Electrics . . . . . . ......... 141
Frame . . ................ 143
Dimensions . . . ......... 143
Weights ................ 144
10 Service . . . . ......... 145
BMW Motorrad
service . ................ 146
BMW Motorrad service
quality . ................ 146
BMW Motorrad Service
Card - On-the-spot
breakdown
assistance . . . . ......... 147
BMW Motorrad service
network ................ 147
Maintenance work . ..... 147
Maintenance
schedules . . . . . ......... 148
Confirmation of
maintenance work . ..... 149

Confirmation of
service . . . .............. 154

Tyre pressure close to limit
of permitted toleranceGeneral warning light
lights up yellow.
The critical tyre pressure
flashes.
Measured tyre pressure is
close to the limit of permitted
tolerance. Correct the tyre pressure as
stated on the inside cover of
the Rider's Manual.
The tyre-pressures listed
on the inside cover are
temperature-compensated;
the reference tyre temperat-
ure for these readings is al-
ways 20 °C. The procedure
for correctly tyre pressures
when the tyres are not at this
reference temperature is as
follows:
Calculate the difference
between the specified value
stated in the Rider's Manual and the reading shown by the
RDC system. Use the public
air line at a petrol station or
motorway service area to
adjust the tyre pressure by
this amount.
Tyre pressure outside
permitted tolerance
General warning light
flashes red.
The critical tyre pressure
flashes.
Measured tyre pressure is
outside permitted tolerance. Check the tyre for damage
and to ascertain wheth-
er the motorcycle can be
ridden with the tyre in its
present condition.
If the motorcycle can be rid-
den with the tyre in its present
condition: Incorrect tyre pressures
impair the motorcycle's
handling characteristics.
If tyre pressure is incorrect it
is essential to adapt your style
of riding accordingly.
Correct the tyre pressure at
the earliest possible oppor-
tunity.
Have the tyre checked for
damage by a specialist
workshop, preferably an
authorised BMW Motorrad
dealer.
If you are unsure whether the
motorcycle can be ridden with
the tyre in its present condi-
tion: Do not continue your jour-
ney.
Notify the breakdown ser-
vice.
Have the tyre checked for
damage by a specialist
workshop, preferably an
331zStatus indicators

Recommended fuel
grade
95 ROZ/RON (Premium
unleaded (fuel grade,
usable with power- and
consumption-related
restrictions)) Usable fuel capacity
19 l Reserve fuel
4l
Press the filler cap down
firmly to close.
Remove the key and close
the protective cap.
Tyre pressure control
RDC
OE
FunctionA sensor integrated into each
tyre measures the air tem-
perature and the air pressure
inside the tyre and transmits
this information to the control
unit.
Each sensor has a
centrifugal-force tripswitch
that does not enable
transmission of the measured
values until the motorcycle
has accelerated to about
30 km/h. The display shows--
for each tyre until the
tyre-pressure signal is
received for the first time. The
sensors continue to transmit
the measured-value signals
for approximately 15 minutes
after the motorcycle comes to
a stop. The control unit can
administrate four sensors, so
two different sets of wheels
with RDC sensors can be
alternated on the motorcycle.
An error message is issued
if wheels without sensors
are fitted to a motorcycle
equipped with an RDC control
unit.
Temperature
compensationThe tyre-pressure readings
shown by the multifunction
display are temperature-
compensated; the reference
tyre temperature for these
readings is always 20 °C.
The air lines available to
the public in petrol stations
and motorway service areas
almost invariably show
temperature-dependent
tyre pressures, so in most
instances these gauge
572zRiding

General instructionsThe 'Maintenance' chapter
describes work involving the
replacement of wear parts
that can be performed with
minimum effort.
Special tightening torques are
listed as applicable.
If you are interested in inform-
ation on more extensive work,
we recommend the repair
manual on CD-ROM which
applies to your particular mo-
torcycle. You can obtain a
copy from your authorised
BMW Motorrad dealer.
Some of the work calls for
special tools and a thorough
knowledge of motorcycles.
If you are in doubt consult a
specialist workshop, prefer-
ably your authorised BMW
Motorrad dealer.
ToolkitStandard on-board
toolkit1 Screwdriver with
reversible bladeRemoving and installing turn
indicator glass
Disconnecting leads from
battery terminals
2Torx wrench, T25 Removing and installing
body panels
Removing and installing bat-
tery retainer 3 Screwdriver, small
Removing and installing turn
indicator glass
On-board toolkit service
kitYour authorised BMW Mo-
torrad dealer can provide the
on-board toolkit service kit
that you will need if you are
considering undertaking more
extensive work.
You will find information
on undertaking work of
this nature in the Repair
Manual on the CD-ROM
also obtainable from your
authorised BMW Motorrad
dealer.
788zMaintenance

Paint careWashing the motorcycle
regularly will help counteract
the long-term effects of
substances that damage
the paint, especially if your
motorcycle is ridden in areas
with high air pollution or
natural sources of dirt, for
example tree resin or pollen.
Remove particularly
aggressive substances
immediately, however, as
otherwise the paint can
be affected or become
discoloured. Substances
of this nature include spilt
fuel, oil, grease, brake fluid
and bird droppings. We
recommend BMW vehicle
polish or BMW paint cleaner
for this purpose.
Marks on the paintwork are
particularly easy to see after
the motorcycle has been
washed. Remove stains ofthis kind immediately, using
cleaning-grade benzene or
petroleum spirit on a clean
cloth or ball of cotton wool.
We recommend that specks
of tar be removed with BMW
tar remover. Remember to
wax the parts treated in this
way.
Protective wax
coatingFor the protective wax coating
of paint, we recommend that
you use only BMW vehicle
wax or agents that contain
carnauba wax or synthetic
waxes.
It is time to rewax the paint-
work when water "puddles"
on the surface, instead of
forming beads.
Laying up the
motorcycleClean the motorcycle.
Remove the battery.
Spray the brake and clutch
lever pivots and the main
and side stand pivots with a
suitable lubricant.
Coat bright metal and
chrome-plated parts with
an acid-free grease (e.g.
Vaseline).
Stand the motorcycle in a
dry room in such a way that
there is no load on either
wheel.
Before laying the vehicle
up out of use, have the
engine oil and the oil filter ele-
ment changed by a special-
ist workshop, preferably an
authorised BMW Motorrad
dealer. Combine work for lay-
ing up/restoring to use with a
BMW service or inspection.
8128zCare

Service
BMW Motorrad service . . . . . . . 146
BMW Motorrad service
quality . . . . . . . . . . . . . . . . . . . . . . . 146
BMW Motorrad Service Card -
On-the-spot breakdown
assistance . . . . . . . . . . . . . . . . . . . 147
BMW Motorrad service
network . . . . . . . . . . . . . . . . . . . . . . 147
Maintenance work . . . . . . . . . . . . 147
Maintenance schedules . . . . . . . 148
Confirmation of maintenance
work . . . . . . . . . . . . . . . . . . . . . . . . . 149
Confirmation of service . . . . . . . 154
10145zService