2006 BMW MOTORRAD K 1200 S headlight bulb

Rear light bulb defectiveGeneral warning light
lights up yellow.
The
LAMPR!
warning ap-
pears on the display.
A defective bulb places
your safety at risk be-
cause it is easier for other
users to oversee you and
your motorcycle.
Replace defective bulbs as
soon as possible; always
carry a complete set of spare
bulbs if possible.
Rear light or brake light bulb
defective.
Replacing brake light and
rear light bulb ( 113)
Front light bulb defective
The
LAMPF!
warning ap-
pears on the display. A defective bulb places
your safety at risk be-
cause it is easier for other
users to oversee you and
your motorcycle.
Replace defective bulbs as
soon as possible; always
carry a complete set of spare
bulbs if possible.
Low-beam headlight, high-
beam headlight, side-light or
turn-indicator bulb defective.
Replacing low-beam head-
light bulb ( 109)
Replacing high-beam head-
light bulb ( 111)
Replacing parking-light bulb
( 113)
Replacing front turn indicat-
or bulbs ( 115)
Replacing rear turn indicator
bulbs ( 117) Bulbs defective
General warning light
lights up yellow.
The
LAMPS!
warning ap-
pears on the display.
A defective bulb places
your safety at risk be-
cause it is easier for other
users to oversee you and
your motorcycle.
Replace defective bulbs as
soon as possible; always
carry a complete set of spare
bulbs if possible.
A combination of the bulb de-
fects described above has
occurred.
See the fault descriptions
above.
Ice warning Ice warning symbol ap-
pears on the display.
327zStatus indicators

this substitute rear light, the
indicators in the display tell
you that a bulb defect has oc-
curred.A defective bulb places
your safety at risk be-
cause it is easier for other
users to oversee you and
your motorcycle.
Replace defective bulbs as
soon as possible; always
carry a complete set of spare
bulbs if possible.
The bulb is pressurised
and can cause injury if
damaged.
Wear protective goggles
and gloves when changing
bulbs.
The types of bulb fitted
to your motorcycle are
listed in the section entitled
"Technical data". Do not touch the glass
of new bulbs with your
fingers. Use a clean, dry cloth
to hold the bulbs when hand-
ling them. Dirt deposits, in
particular oil and grease, in-
terfere with heat radiation
from the bulb. This leads to
overheating and shortens the
bulb's operating life.
Replacing low-beam
headlight bulb
If it is not standing firmly,
the motorcycle could
topple in the course of the
operations described below.
Always make sure that the
motorcycle is stable and
firmly supported.
Turn the handlebars
to the left to facilitate
access. Make sure the ground is
level and firm and place the
motorcycle on its stand.
Switch off the ignition.
Turn cover
1counter-
clockwise and remove
it.
7109zMaintenance

Disconnect plug2.
Release spring clip 3at left
and right and swing it up. Remove bulb
4.
Replace the defective bulb.
Low-beam headlight
bulb
H7/12V/55W Install bulb
4; make sure
that tab 5is pointing up.
Engage spring retainer 3on
left and right.
7110zMaintenance

Connect plug2.
Turn cover 1clockwise to
install.
Replacing high-beam
headlight bulb
If it is not standing firmly,
the motorcycle could
topple in the course of the
operations described below.
Always make sure that the
motorcycle is stable and
firmly supported.
Turn the handlebars
to the left to facilitate
access.
Make sure the ground is
level and firm and place the
motorcycle on its stand.
Switch off the ignition. Turn cover
1counter-
clockwise and remove
it.
Disconnect plug 2.
7111zMaintenance

Release spring clip3at left
and right and swing it up.
Remove bulb 4.
Replace the defective bulb. High-beam headlight
bulb
H7/12V/55W
Install bulb 4; make sure
that tab 5is pointing up. Engage spring retainer
3on
left and right.
Connect plug 2.
7112zMaintenance

Turn cover1clockwise to
install.Replacing parking-light
bulb
If it is not standing firmly,
the motorcycle could
topple in the course of the
operations described below.
Always make sure that the
motorcycle is stable and
firmly supported.
Make sure the ground is
level and firm and place the
motorcycle on its stand. Switch off the ignition.
Pull off the connector
1be-
neath the headlight.
Remove bulb holder 2from
the headlight housing by
turning it counter-clockwise.
Remove bulb 3from the
bulb holder.
Replace the defective bulb.
Parking-light bulb
W5W / 12 V / 5 W Install bulb
3in bulb sock-
et 2.
Turn the bulb socket clock-
wise to install it in the head-
light housing.
Connect plug 1beneath the
headlight.
Replacing brake light
and rear light bulb
If it is not standing firmly,
the motorcycle could
topple in the course of the
operations described below.
Always make sure that the
7113zMaintenance

Technical data
Spark plug manufacturer and designation NGK KR9CI
Spark plug electrode gap0.8 mm, When new
Spark plug electrode gap (Wear limit) No wear limit; spark-plug replacement as per
maintenance schedule
Lighting
High-beam headlight bulb H7 / 12 V / 55 W
Low-beam headlight bulb H7 / 12 V / 55 W
Parking-light bulb W5W / 12 V / 5 W
Bulb of tail light/brake light P21W / 12 V / 21 W
Front flashing turn indicator bulbs W16W / 12 V / 16 W
Rear flashing turn indicator bulbs R10W / 12 V / 10 W
9142zTechnical data

A
Abbreviations and symbols, 6
Anti-theft alarm, 17
B
BatteryCharging battery when
connected, 120
Charging battery when
disconnected, 121
Installation, 121, 122
Removal, 121, 122
Technical data, 141
Warning, battery charge
current, 26
Brake fluid Checking level, front, 94
Checking level, rear, 95
Brake pads Checking front, 92
Checking rear, 93
Brakes Technical data, 140
Breakdown assistance kit, 85 Bulbs
General instructions, 108
Replacing brake-light
bulbs, 113
Replacing front turn
indicator bulbs, 115
Replacing high-beam
headlight bulb, 111
Replacing low-beam
headlight bulb, 109
Replacing parking-light
bulb, 113
Replacing rear light
bulbs, 113
Replacing rear turn indicator
bulbs, 117
Technical data, 142
Warning, bulb failure, 27
C
Case Adapting, 84
Adjusting, 82
Closing, 82
Installing, 84 Opening, 82
Removing, 83
Checklist, 66
Clock, 20 Adjusting, 42
Clutch Fluid reservoir, 11, 13
Technical data, 137
Confirmation of maintenance work, 149
E
Electrics Technical data, 141
Emergency off switch (kill switch), 16, 48
Engine Technical data, 134
Temperature gauge, 20, 21
Warning, engine electron-
ics, 25
Engine oil Checking level, 89
Draining, 91
Technical data, 136
11156zIndex