2006 BMW M3 CONVERTIBLE maintenance

37
Indicator lamp displays>The indicator lamp below the interior
rearview mirror flashes continuously:
the system is armed
>The indicator lamp flashes immedi-
ately after the vehicle is locked: doors
or luggage compartment lid are not
completely closed. Even if you do not
close the alerted area(s), the remain-
ing areas are secured, and the indi-
cator lamp will flash continuously
after 10 seconds. However, the inte-
rior motion sensor is not activated
>The indicator lamp goes out immedi-
ately after the vehicle is unlocked: no
manipulation or attempted intrusions
have been detected in the period
since the system was armed
>The indicator lamp flashes for
10 seconds immediately after the
vehicle is unlocked: an attempted
entry has been detected in the period
since the system was armed.
Following triggering of an alarm, the
indicator lamp will flash continuously.Tilt alarm sensor and interior
motion sensorTilt alarm sensor:
The tilt of the vehicle is monitored. The
alarm system reacts, for example, to
attempts to steal the wheels or tow the
vehicle.
Interior motion sensor:
The vehicle interior is monitored up to
the height of the seat cushions. Even
when the convertible top is open, the
alarm system including the interior
motion sensor is armed. Objects falling
into the vehicle, e.g. leaves, can trigger
unintentional alarms, refer to Avoiding
unintentional alarms.Avoiding unintentional alarmsThe tilt alarm sensor and interior motion
sensor may be switched off at the same
time. You can do this to prevent a false
alarm, e.g. in the following situations:
>In garages with elevator ramps>When the vehicle is being trans-
ported by train
>When animals are to remain in the
vehicle.
Deactivating the tilt alarm and
interior motion sensors>Press the button on the remote con-
trol twice.
The indicator lamp lights up briefly and
then flashes continuously. The tilt alarm
sensor and the interior motion sensor
are deactivated until the vehicle is
unlocked and locked again.
You can have the tilt alarm sensor
and the interior motion sensor
permanently deactivated.<
The system deactivates the tilt
alarm sensor and the interior
motion sensor if the convenience clos-
ing of windows and glass sunroof is
interrupted within the first 10 seconds
and then restarted. The vehicle must
then be unlocked and relocked before
the sensors will resume operation.<
Alarm system*
OverviewControlsMaintenanceRepairsDataIndex

39
Despite trap protection, always
make sure that the windows can
close without obstruction, otherwise in
some cases, e.g. with thin objects, it is
not guaranteed that the closing opera-
tion will be interrupted.
Trap protection is restricted when the
switch is pulled and held beyond the
pressure point.<
After a power lossAfter the battery has been discon-
nected, the trap protection must be
reinitialized. Perform the following pro-
cedure twice for each window:
>Open and close the window com-
pletely
>With the window closed, keep pulling
the switch upward for approx.
1 second.
Convertible topThe completely automatically operated
convertible top combines assured pro-
tection against the elements with sim-
ple and easy handling.
To gain maximum satisfaction from your
convertible, please observe the follow-
ing:
>It is advisable to close the convertible
top when the vehicle is being parked.
The closed convertible top not only
protects the passenger compartment
from unforeseeable damage from the
weather, it also provides a certain
degree of theft protection. In addi-
tion, keep valuables only in the
locked luggage compartment, even
when the convertible top is closed
>Never mount a roof-mounted luggage
rack system on the convertible top.
At temperatures below 147/
–106 do not operate the convert-
ible top to prevent damage. Never store
the convertible top in its compartment
for more than one day while it is wet to
avoid permanent damage from mois-
ture.<
Do not lay objects on the convert-
ible top, as they could fall off
when it moves, causing vehicle damage
or personal injury.<
Electric power windows
OverviewControlsMaintenanceRepairsDataIndex

41
2. Ensure that the convertible top com-
partment panel in the luggage com-
partment is folded down, refer to
page 35; otherwise, it will not be
possible to open the convertible top
3. Make sure that the luggage compart-
ment lid is closed
4. Press and hold the corresponding
button for convertible top operation.
It can take a few seconds until the
opening or closing procedure starts.
The luggage compartment lid can-
not be opened while the convert-
ible top is in motion.<
During convertible top operation
the rear window moves toward the
passenger compartment. To prevent
injuries, make sure that the closing path
of the convertible top is unobstructed.<
After having been stored for an
extended period of time in the
convertible top compartment, e.g. dur-
ing the winter months because the
hardtop was being used, you may have
to support the convertible top by hand
when closing it for the first time.
If the convertible top should halt right
before the closing phase is completed,
press against the front part of the con-
vertible top frame from the outside to
help the closing process along. Keep
pressing the button while doing so until
the top starts up again on its own.<
Indicator lamps>The red indicator lamp is lit whenever
the convertible top is in motion. It
goes out as soon as the opening or
closing operation has been com-
pleted
>If the red indicator lamp flashes after
the button is released, the convertible
top has not yet been opened or
closed completely. You can resume
operation in the desired direction by
pressing the button again
>If the yellow indicator lamp lights up
continuously with the button pressed,
the convertible top compartment
panel has been raised and the top
cannot be moved.
The side windows move down slightly
whenever the button for operating the
convertible top is pressed.
They will go back up if you keep holding
the button down for more than
2 seconds after the opening or closing
process has been completed and the
indicator lamp has gone out.InterruptionThe convertible top stops moving
immediately when the button is
released. You can resume operation in
the desired direction by pressing the
button again.
Do not close the side windows
using the power window switches
if the convertible top has not been
closed completely. Otherwise, the side
windows may not seal properly with the
rubber seals of the convertible top.<
If the opening or closing operation is
interrupted by releasing the buttons,
the convertible top remains in the
respective position for 15 minutes
before it slowly moves into a stable
position. The operation can be contin-
ued by pressing the buttons.
Convertible top
OverviewControlsMaintenanceRepairsDataIndex

43
4. Grasp the convertible top by the lat-
eral guide section – see arrow 1 –
and the front convertible top frame –
see arrow 2. Lift out the top and
swing forward until you encounter a
perceptible resistance at a stop.
Position the rear convertible top
frame vertically and close the con-
vertible top compartment lid. Fold
down the rear convertible top frame
To avoid damaging the side trim,
always fold the convertible top
forward before folding the rear frame
brace up into its vertical position.<
5. Use a screwdriver to lift out the cover
panel that is in the center of the front
convertible top frame
6. Insert the Allen wrench 2 – refer to
page 42 – into the recess – see arrow
7. Pull down on the front convertible
top frame as far as possible. Close
the convertible top further by turning
the wrench in a clockwise direction;
continue turning until the front con-
vertible top frame is locked to the
windshield frame. The rear convert-
ible top frame will automatically be
pressed down onto the convertible
top compartment lid and, because of
the tension, will close completely.
The closing operation must be
completed, as otherwise damage
and/or injuries may result.<
Please consult your BMW center
to have the defect corrected.<
Convertible top
OverviewControlsMaintenanceRepairsDataIndex

45
3. Hold the wind deflector so that the
smaller half points toward the front
and guide the mounting pin for the
side piece into the proper opening
4. Pull back on the mounting pin for the
other side piece by using a slide, so
that the mounting pin can be guided
into the opening provided
5. Unlock the convertible top compart-
ment lid via the convertible top con-
trol button, refer to page 40, and
open the convertible top compart-
ment lid
6. Flip the back half of the wind deflec-
tor backward, so that the mounts are
lying on the vehicle
7. Close the convertible top compart-
ment lid via the convertible top con-
trol button. The wind deflector is now
attached so that it is theft-proof.
Operate the convertible top com-
partment lid from above only in
order to avoid any pinching.
With the wind deflector in place: to
avoid damaging the wind deflector
never push the front seats all the way
back. installing, just reverse the steps.
Wind deflector*
OverviewControlsMaintenanceRepairsDataIndex

47
SeatsWhen adjusting your seat, always
observe the following precautions
Never try to adjust your seat while
operating the vehicle. The seat
could respond with an unexpected
movement, and the ensuing loss of
vehicle control could lead to an acci-
dent. Never ride with the backrest
reclined to an extreme horizontal angle
– important for front passengers to
remember. If you do, there is a risk that
you will slide under the safety belt in an
accident, thus reducing the protection
provided by the safety belt.
With the wind deflector in place:
Do not push the front seats all the way
back, otherwise the wind deflector will
be damaged.<
Adjusting the seats>Power seat adjustment, refer to
page 47
>Head restraint, refer to page 48
>Entering the rear, refer to page 49
Power seat adjustmentSeat adjustment1Tilt angle
2Forward/backward adjustment
3Height
4Backrest angle
You can manually adjust the thigh sup-
port.
Thigh supportPull the lever and adjust the position of
the cushion for thigh support as
desired.
OverviewControlsMaintenanceRepairsDataIndex

49
Rear head restraints
The rear head restraints may only
be lowered if there are no passen-
gers in the rear seats. If you do so, you
are in violation of the law. Raise the rear
head restraints before taking on any
passengers in the back.<
To completely lower the rear head
restraints:
1. Press the button and hold it down
2. Push the head restraint down from
above.
Raising the rear head restraintsRaise the head restraints until you hear
them click into place.
Do not remove the rear head
restraints as this would damage
them.<
For further information, please consult
your BMW center.
Do not use the rear head
restraints as storage shelves.
Always keep the travel path for the roll-
over protection system free and clear.
Under no circumstances should you put
any kind of cover such as an antima-
cassar on the head restraints, refer also
to the labeling on the head restraints.<
Entering the rearThe seat-integrated safety belt system
allows for easy access to the rear.
1. Lift lever 1 up and tilt the backrest
forward until it engages
2. Press and hold button 2 in driving
direction until the seat moves to the
desired position
3. After entering the rear, fold back and
lock the backrest
4. Press button 2 opposite the direction
of travel and hold. The seat moves
back into its previous position. If the
button 2 is released beforehand, the
seat stops in the respective position.
Head restraints
OverviewControlsMaintenanceRepairsDataIndex

51
Seat and mirror memoryYou can store and recall three different
driver's seat and outside mirror posi-
tions.
Memory will not retain the adjust-
ment made to the lumbar sup-
port. 2. Adjust your seat and outside mirrors
to the desired position
3. Press the M
EMORY
button: the indica-
tor lamp in the button lights up
4. Press memory button 1, 2 or 3, as
desired. The indicator lamp goes out.
To select a stored setting
Do not select a memory position
while the vehicle is moving. If you
do so, there is a risk of accident from
unexpected seat movement.<
Driver's door open after unlocking or
ignition key in position 1:
>Briefly press memory button 1, 2 or 3,
as desired.
Movement stops immediately when
one of the seat-adjustment or mem-
ory buttons is operated during the
adjustment process.
With the driver's door closed and the
ignition key either removed or in posi-
tion 0 or 2:
>Press and hold the desired memory
button – 1, 2 or 3 – until the adjust-
ment process is completed.
If you press the M
EMORY
button acci-
dentally: press the button again; the
indicator lamp goes out.
You can have this feature pro-
grammed so that when you use
the remote control from your personal-
ized key to unlock your door, your seat
and the exterior mirrors will move into
your own preferred positions.<
Before activating the programmed
adjustment feature, ensure that
the footwell behind the driver's seat is
empty and unobstructed. If you fail to
do so, persons, animals or objects
could be injured or damaged if the seat
should move backward.<
OverviewControlsMaintenanceRepairsDataIndex